asterisk users - Dec 2009 - dahdi_tool shows no alarms, but no line connected

Hi,

I'm using Sangoma's wanpipe together with dahdi, all
software downloaded today at most recent version.
Hardware is Sangoma A104, a 4xE1 card.
Installation went well.

Anyway, wanrouter status shows a different result than
dahdi_tool or dahdi_scan.

I've just put a hardware loop on port 1. All the other
ports are open.

wanrouter status shows the expected result:
Device name | Protocol | Station | Status        |
wanpipe1    | AFT TE1  | N/A     | Connected     |
wanpipe2    | AFT TE1  | N/A     | Disconnected  |
wanpipe3    | AFT TE1  | N/A     | Disconnected  |
wanpipe4    | AFT TE1  | N/A     | Disconnected  |

However:
# dahdi_scan 2
[2]
active=yes
alarms=OK
description=wanpipe2 card 1
name=WPE1/1
manufacturerdevicetypelocationbasechan=1
totchans=31
irq=0
type=digital-
syncsrc=0
lbo=0 db (CSU)/0-133 feet (DSX-1)
coding_opts=HDB3
framing_opts=CCS,CRC4
coding=HDB3
framing=CCS


Why are the dahdi tools not reflecting the values
by wanrouter?

Roger.

On Thu, Dec 03, 2009 at 01:13:13AM +0100, Roger Schreiter
wrote:
> Hi,
> 
> I'm using Sangoma's wanpipe together with dahdi, all
> software downloaded today at most recent version.
> Hardware is Sangoma A104, a 4xE1 card.
> Installation went well.
> 
> Anyway, wanrouter status shows a different result than
> dahdi_tool or dahdi_scan.
> 
> I've just put a hardware loop on port 1. All the other
> ports are open.
> 
> wanrouter status shows the expected result:
> Device name | Protocol | Station | Status        |
> wanpipe1    | AFT TE1  | N/A     | Connected     |
> wanpipe2    | AFT TE1  | N/A     | Disconnected  |
> wanpipe3    | AFT TE1  | N/A     | Disconnected  |
> wanpipe4    | AFT TE1  | N/A     | Disconnected  |
> 
> However:
> # dahdi_scan 2
> [2]
> active=yes
> alarms=OK
> description=wanpipe2 card 1
> name=WPE1/1
> manufacturer> devicetype> location> basechan=1
> totchans=31
> irq=0
> type=digital-
> syncsrc=0
> lbo=0 db (CSU)/0-133 feet (DSX-1)
> coding_opts=HDB3
> framing_opts=CCS,CRC4
> coding=HDB3
> framing=CCS
> 
> 
> Why are the dahdi tools not reflecting the values
> by wanrouter?
What does the driver report?

head -n1 /proc/dahdi/*

If there are no alarms there, the wanpipe driver probably did not report
them to DAHDI.

-- 
               Tzafrir Cohen
icq#16849755              jabber:tzafrir.cohen at xorcom.com
+972-50-7952406           mailto:tzafrir.cohen at xorcom.com
http://www.xorcom.com  iax:guest at local.xorcom.com/tzafrir

Tzafrir Cohen schrieb:
> ...
> head -n1 /proc/dahdi/*
# head -n1 /proc/dahdi/*
==> /proc/dahdi/1 <=Span 1: WPE1/0 "wanpipe1 card 0" (MASTER)
HDB3/CCS/CRC4

==> /proc/dahdi/2 <=Span 2: WPE1/1 "wanpipe2 card 1"
HDB3/CCS/CRC4

==> /proc/dahdi/3 <=Span 3: WPE1/2 "wanpipe3 card 2"
HDB3/CCS/CRC4

==> /proc/dahdi/4 <=Span 4: WPE1/3 "wanpipe4 card 3"
HDB3/CCS/CRC4

> If there are no alarms there, the wanpipe driver probably did not report
> them to DAHDI.
Probably. But why? (When I turn of wanpipes, I can
see them disapear with dahdi_tool.)

How can I investigate the reason?

Roger.


-- 
Roger Schreiter
Spindelberg 11
D-74354 Besigheim
Tel.: +49 7143 36476