search for: wanrouter

...s goes into sleep and that's when all the 4 Dahdi channels are lost. So, I have been getting Monday morning calls (Tuesday today but yesterday was a day off anyhow) for the past 3 weeks complaining no inbound/outbound calls can be made through PSTN. When I log in to the server if I do a "wanrouter hwprove" I only see one of the units. If I ask them to disconnect and reconnect the U100 that is flashing (which is the one that failed) and do "wanrouter hwprobe" now it shows again. So, I can do a wancfg_dahdi and it brings it up. Sometimes, I have to recompile the whole wanpipe. B...

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting tips. "*wanpipe1 | AFT TE1 | N/A | Disconnected |" <<<<<* This is what shows. root at pbx...

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name | Protocol | Station | Status | wanpipe1 | AFT TE1 | N/A | Connected | wanpipe2 |...

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk# /etc/init.d/dahdi stop Unloading DAHDI hardware modules: ERROR: Module wanpipe is in use ERRO...

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference: 99.996683 [root a...

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

...erisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-A101u : SLOT=1 : BUS=1 : IRQ=209 : CPU=A : PORT=PRI Card Cnt: S508=0 S514X=0 S518=0 A101-2=1 A104=0 A300=0 So I know the card is there OK. My /etc/zaptel.conf looks like: span=...

...We are about to try the card and four *seperate* UK BT lines in a 32bit system. The current system is a 4gb, dual core cpu with pbx in a flash 1.4, Zaptel and Asterisk 1.4.21-2 Currently we have put in a temp OpenVOX tdm400 card and it works perfectly. As soon as we swap that and use Sangoma via wanrouter we get crosstalk. For example, if an existing call is happening and a new internal to external call or vise versa happens, they can hear each other, even just to IVR. Any ideas? All wiring has been checked and this *does not*, I repeat, *does not* happen with the Sangoma card. So what ever explain...

...8 - Bearer capability not available) == Everyone is busy/congested at this time (1:0/0/1) -- Executing [691918892 at pbx1:2] Hangup("SIP/xtravoip200-009d24b0", "") in new stack == Spawn extension (pbx1, 691918892, 2) exited non-zero on 'SIP/xtravoip200-009d24b0' wanrouter status: wanrouter status Devices currently active: wanpipe1 wanpipe2 wanpipe3 wanpipe4 wanpipe5 wanpipe6 wanpipe7 wanpipe8 Wanpipe Config: Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate | wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 17 | 4...

In my Asterisk CLI I get Ring/Off-hook in strange state 6 when i make a call into the system, the system claims to answer the call, and do the things in the dial plan, but I just hear ringing on the phone I'm calling in from. I am using a Sangoma A200 4 Port Analog card. my wanrouter version: WANPIPE Release: 3.3.6 asterisk -V: PBXtra Core fon_o_1.2.17 Any ideas? Daniel Lockard

...out that the Sangoma card had suddently decided to stop answering on channels 2,3 and 4, so if someone was using channel 1, then no other calls would be picked up. We could, however, make outgoing calls. I tried restarting Asterisk and it didn't make a difference. I then tried restarting the Wanrouter and it started working again. Has anyone else run into this problem? I really don't like the fact that I had to restart the wanrouter for the channels to start behaving normally again. Our phone system is basically useless if it randomly downgrades to a single line. I'm going to speak t...

...E1) I can see the call answered/placed on the CLI and then silence follows. I've been provisioned 25 out of the 31 channels only at the moment and I'm using a "dummy" number given by BT for testing. The is no alarms on the line, nor errors on the CLI or in the /va/log/messages or wanrouter. Any ideas? Thank you much. Veselin -- Regards, Veselin Kantsev veselin at campbell-lange.net Campbell-Lange Workshop

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

...2fxs+2fxo"). Any reference > >? > can > >? > >? help? > >? > > > >? > >? For example, what does it mean > to use > >? > "/sbin/modprobe > >? > >? qozap" and why u used next to > it > >? > "/usr/sbin/wanrouter > >? > >? start" and what that wanrouter. > >? > > > >? > >? Any help? > >? > >? Please look for my current > rc.local file. > >? > > > >? > > > >? > > >? > Bilal, > >? > > >? > qozap...

...2fxs+2fxo"). Any reference > >? > can > >? > >? help? > >? > > > >? > >? For example, what does it mean > to use > >? > "/sbin/modprobe > >? > >? qozap" and why u used next to > it > >? > "/usr/sbin/wanrouter > >? > >? start" and what that wanrouter. > >? > > > >? > >? Any help? > >? > >? Please look for my current > rc.local file. > >? > > > >? > > > >? > > >? > Bilal, > >? > > >? > qozap...

...oading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid argument Wanpipe driver did not load properly Please check /var/log/wanrouter and /var/log/messages for errors Configuring interfaces: w1g1 w1g1: ERROR while getting interface flags: No such device done. /etc/wanpipe/scripts/start: 7: Syntax error: Bad for loop variable DAHDI_SPANCONFIG failed on span 1: No such device or address (6) Dont know why I still keep get...

...ranch of asterisk 1.8 and i didn't found dahdi command in CLI everything seem fine. am i missing something ? campbx2*CLI> dahdi <tab tab> No such command 'dahdi' (type 'core show help dahdi' for other possible commands) campbx2*CLI> root at campbx1:/etc/wanpipe# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-A102-SH : SLOT=2 : BUS=7 : IRQ=3 : CPU=A : PORT=1 : HWEC=64 : V=37 2 . AFT-A102-SH : SLOT=2 : BUS=7 : IRQ=3 : CPU=A : PORT=2 : HWEC=64 : V=37 Card Cnt: A101-2=1 root at campbx2:/etc/...

...driver I type: WANPIPE_FOLDER# ./Setup install Everything seems to be ok. There are no broken dependencies and the hardware is well detected, even zaptel is recompiled with no errors, but at the time to compile wanpipe I'm getting this error message: ------------------ include/linux/wanrouter.h:344: error: expected specifier-qualifier-list before ?get_info_t? ------------------ Could anyone help me on this. Thanks in advance. -- ._._._._._._._._._._._._._._._._._._._._ D.G.S.C.A U.N.A.M Direcci?n de Telecomunicaciones Proyectos Especiales...

...Linux Asterisk 1.4.24.1, Copyright (C) 1999 - 2008 Digium, Inc. and others. WANPIPE Release: 3.4.1 Wanpipe Config: Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate | wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 169 | 4 | 1 | N/A | 0 | Wanrouter Status: Device name | Protocol | Station | Status | wanpipe1 | AFT TE1 | N/A | Connected | Local sets are all Aastra 9143's. - dbc. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/atta...