search for: dahdi_tool

Hi All, I have installed newt and newt_devel but dahdi_tool will not compile/install. I'm trying this with dahdi-linux-complete-2.5.0.2+2.5.0.2. does anyone have any suggestions as to what I am doing wrong? Regards David. -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-use...

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name | Protocol | Station | Status | wanpipe1 | AFT TE1 | N/A | Connected | wanpipe2 | AFT TE1 | N/A | Disconnected | wanpipe3...

Usually I used real Digium cards in asterisk systems, so I'm running into this for the first time. dahdi_tool reports that dahdi_dummy is in state UNCONFIGURED. This isn't super surprising, as it seems like the configuration files for DAHDI are really intended only for configuring real physical cards. But that begs the question: Is there any legal DAHDI configuration for dahdi_dummy such that dahdi_to...

...05] Wrote 0x0 to register 0x1ab but got back 0x4 [ 377.618423] Wrote 0x0 to register 0x1ab but got back 0x4 [ 378.130266] Wrote 0x0 to register 0x1ab but got back 0x4 [ 378.642088] Wrote 0x0 to register 0x1ab but got back 0x4 [ 1202.812870] show_signal_msg: 21 callbacks suppressed [ 1202.812876] dahdi_tool[1277]: segfault at 3fc378fa0 ip 00000000004021ac sp 00007fff131dd930 error 4 in dahdi_tool[400000+3000] And a lot of "Wrote 0x0 to register 0x1ab but got back 0x4" statements. If i run dahdi_tools it fails with a segmentation fault. Any suggestions are appreciated! Kind regards, Marc...

...like the gain is too high somewhere, and the audio is overdriven. Is this a problem at the carrier? I'm trying to call them now, but it's Sunday morning in the sticks, and my chances of getting someone with a clue are slim to none. I restarted dahdi but that had no effect. I watched dahdi_tool as calls came in and out but there isn't really a lot of information there. Sangoma has a cool tool "wanpipemon" that shows error stats and such on the span. Is there such a tool for Digium cards? Any suggestions? Thanks, -- Jeff LaCoursiere SunFone jeff at sunfone.com

...unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware pci:0000:03:08.0 wct4xxp+ d161:0220 Wildcard TE220 (4th Gen) astpbx ~ # But dahdi_tool does not show the card and dahdi_cfg gives DAHDI_SPANCONFIG failed on span 1: Invalid argument (22) System info is provided here - http://asteriskpbx.ru/pastebin/12 Please advise. -- Maxim Litnitskiy http://asteriskpbx.ru http://asterisk-support.ru -------------- next part -------------- An HTML...

..../usr/sbin/dahdi_cfg -./usr/sbin/dahdi_diag ./usr/sbin/dahdi_genconf ./usr/sbin/dahdi_hardware ./usr/sbin/dahdi_maint ./usr/sbin/dahdi_monitor ./usr/sbin/dahdi_registration ./usr/sbin/dahdi_scan +./usr/sbin/dahdi_span_assignments +./usr/sbin/dahdi_span_types ./usr/sbin/dahdi_test ./usr/sbin/dahdi_tool -./usr/sbin/fpga_load +./usr/sbin/dahdi_waitfor_span_assignments ./usr/sbin/fxotune -./usr/sbin/fxstest ./usr/sbin/lsdahdi ./usr/sbin/sethdlc ./usr/sbin/twinstar @@ -29,6 +32,15 @@ ./usr/share/ ./usr/share/dahdi/ ./usr/share/dahdi/astribank_hook +./usr/share/dahdi/dahdi_auto_assign_compat +....

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Hi List. I'm running the patlooptest program I've found in dahdi_tools 2.1.0.2. The target is a TE121P board with a loopback cable inserted on the socket. I suppose that the loopback is working fine because I'm able to see the green led on and dahdi_tool reports no errors. When I run the patlooptest I've a lot of errors (the received values are completely di...

Hi sir, I was installed Goautodial server and I have b410p BRI card. BRI card showing OK with dahdi_tool, this NT mode. whenever I am dialing from server i am not able to connect the call . in Cli below mention warning is comming . please what is the mistake with me . help me Executing [0559566768 at default:1] AGI("Console/dsp", "agi:// 127.0.0.1:4577/call_log") in new stack...

...han=1-5 dchan=24 chan_dahdi.conf: [channels] switchtype=national signalling=pri_cpe echocancel=yes echocancelwhenbridged=yes echotraining=400 callerid=asreceived context=smvoice-incoming group=1 channel => 1-5 Any ideas? Also - how do you get a card out of loop mode after you have used the dahdi_tool to select loop mode. there is no UNLOOP or anything. I have reset the machine and it still seems to be in loop mode. Jerry

...rce it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P Board 1 > dahdi_tool (After select select) > Current Alarms: No alarms ( Should I see OK here instead ? Is it normal > ?) > Sync Source: Internally clocked > IRQ Misses: 0 > Bipolar Viol: 0 > Tx/Rx Leve...

...dial it from asterisk , no call can be made. and also, when i try to call from ericsson side, i get line busy message as soon as i dial the number. Is there any guide that can help me in installing that card? PS: Whatever i made in SPAN config, everytime the only thing i see was Internal clock on dahdi_tool . How can i make my e1 card master (or slave whatever) instead of internal clock?? and other thing i wonder, if i create a span like "span=1,0,0,ccs,hdb3" is it zap/g1 in zaptel(dahdi) conf menu in asteriskgui???(or freepbx)

Hello, I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : $ sudo dpkg -l|grep -Ei 'dahdi|asterisk|libpri' ii asterisk 1:11.13.1~dfsg-2+b1 amd64 Open Source Private Branch Exchange (PBX) ii asterisk-config 1:11.13.1~dfsg-2 all Configuration

...Bridge Bridge Interaction Channel no no no ---------- 11 channel drivers registered. But right now, I am planing to connect a PRI trunk to this Asterisk. so I put in a PRI card install dahdi-linux-complete-2.6.2 and libpri-1.4.14. Afterward, dahdi_tool is able to find PRI board, and all channels. But my question is when I try to send call to DAHDI channel in the dial plan, CLI print out a warning saying [Jun 13 07:48:21] WARNING[2393]: channel.c:5606 ast_request: No channel type registered for 'DAHDI' According to my description above, i...

....3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page) and OK (with dahdi_tool) from both sides but I can't dial a single call ("Unable to create DAHDI for unknown reason...") from asterisk to patton. In my setup, my main settings are : Smartnode side: dss1,Net,pp,q931,q921 B410P side: euroisdn,bri_cpe,span=1,1,0,ccs,ami,bchan=1-2,hardhdlc=3 Both devices l...

...I system.conf to "span=1,1,0,ESF,B8ZS" (from "span=1,0,0,ESF,B8ZS") and I am still having the same problem. (Although, the FreePBX DAHDI page only allows me to select "0" in the "Sync/Clock Source" field. "0" is the only option in the drop down.) dahdi_tool is showing some "IRQ Misses" and is listing "Sync Source" at the"Wildcard TE121 Card 0." But, dahdi_scan is returning "syncsrc=1" ********************************************************************************************************************* == Prim...

Hi everybody, I' ve been following this list for a while now. Is there a way to detect the individual and cumulative s/n ratio values for the incoming calls in Asterisk or any other Call Center solution?... -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20111130/d0d53c1f/attachment.htm>

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

I'm using a Te201p card, with unichan, I want to know if my channels are "ready" or in alarm... but uc show channel o uc show channels, doesn't show me anything... Any Ideas? thanks.