Heh guys, I just received a T400 card, I've been using a T100 for a little while, and it works fine when using a raw channelized T1. I'm relocating my asterisk machine, and PRI's will only be available, haven't found any good config info for PRI's, can someone point me to PRI config info, or let me know what changes I need to make in order to bring them up, I imagine, zapata.conf and zaptel.conf will require some changes to bring the PRI up. The PRI is currently hooked up to my cisco controller T1 1/0 framing esf linecode b8zs cablelength short 110 pri-group timeslots 1-24 interface Serial1/0:23 no ip address no logging event link-status isdn switch-type primary-5ess isdn incoming-voice voice no cdp enable Regards MIKE
You mention this is on your cisco, is it a data line, or a voice line? On Wed, 2003-04-30 at 17:20, Michael Baird wrote:> Heh guys, I just received a T400 card, I've been using a T100 for a > little while, and it works fine when using a raw channelized T1. I'm > relocating my asterisk machine, and PRI's will only be available, > haven't found any good config info for PRI's, can someone point me to > PRI config info, or let me know what changes I need to make in order to > bring them up, I imagine, zapata.conf and zaptel.conf will require some > changes to bring the PRI up. The PRI is currently hooked up to my cisco > > controller T1 1/0 > framing esf > linecode b8zs > cablelength short 110 > pri-group timeslots 1-24 > > interface Serial1/0:23 > no ip address > no logging event link-status > isdn switch-type primary-5ess > isdn incoming-voice voice > no cdp enable > > Regards > MIKE > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users-- Steven Critchfield <critch@basesys.com>
asterisk@billheckel.com
2003-May-30 08:26 UTC
[Asterisk-Users] Second T1 ISDN PRI in a group, Dual T400P questions
We are installing our second long distance ISDN T1 and I've been given the option of using the same D channel to control both long distance T1s. Does asterisk support signalling 2 T1s on a single D channel? If it does, how do I go about configuring this so that the work together? On a similar note, since I will have 2 T400Ps in this system, do I need both T1s in a bound group such as the above to be inbound on the same card or can they be split? Also, on the T400P front, when a call is bridged from one channel to another it does have to go through the processor so is there any benefit to terminating both ends of the call on the same T400P? Thanks, Bill Heckel CTO Lots of companies ;)
I can't find documentation for setting up PRI. A push in the right direction would be most appreciated. Thanks -- Mike
Hi, Need help from you guys. I had my Asterisk Set-up using PRI card TE110p, and everything working ok. However, I had bad experience with Asterisk answering call.... The problem was, when outsider calling into Asterisk... Asterisk answered call... CLI---- Accepting Overlap call from (CALLERIDNUM) to (unspecified) channel 0/31 CLI---- Starting Simple Switch on Zap31/1 """""Asterisk wait for 3sec""""""""""" Then jump to the context, and my phone rings. Can some one advice that, reducing the number of sec before passes it to the next context or task???????
Without your configs it ill be hard to see what is going on.> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > chan (Alpha Trilogies Networks) > Sent: Thursday, March 16, 2006 8:15 AM > To: asterisk-users@lists.digium.com > Subject: [Asterisk-Users] PRI Setup > > Hi, > Need help from you guys. I had my Asterisk Set-up using PRI > card TE110p, and everything working ok. However, I had bad > experience with Asterisk answering call.... > The problem was, when outsider calling into Asterisk... > Asterisk answered call... > CLI---- Accepting Overlap call from (CALLERIDNUM) to > (unspecified) channel > 0/31 > CLI---- Starting Simple Switch on Zap31/1 """""Asterisk wait > for 3sec""""""""""" > Then jump to the context, and my phone rings. > > Can some one advice that, reducing the number of sec before > passes it to the next context or task??????? > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >