similar to: PRI Setup

Hi, I am experiencing one-way audio from: SIP Device ----> Asterisk -----> Cisco 7200 The Cisco 7200 has a VXE+ card that will allow you to do SIP. I can pass audio from SIP Device to Asterisk through the Cisco 7200 to the other end, but the Cisco 7200 does not return any audio back to the SIP Device or Asterisk, it seems. I have tried upgrading to 12.3T IOS version, but no

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Has anyone got a Premisys Slimline channel bank working with a Cisco AS5400 or similar? I'm not sure if my unit is bad, or what. I'm using FXS Loop Start. Calling the port connects immediately without ringing the attached phone. If I pick up the phone, it's connected and I can talk to the caller. Hanging up has no effect. I can see the bit transitions (0101 to 1111 when I go

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

List users, It's been a while since I've posted here, but I've been hard at work pushing toward our large scale Asterisk goal and keeping up with this list can be a full time job by itself (I have19,543 unread list messages!!). This Friday, September 16th 2005, my team will be at the MCI Development Lab in Richardson, Texas testing our setup. We have a three server system

I could swear that I remember seeing some announcement somewhere that Zaptel now supported drop-and-insert across spans on a TE410P, but now I can't find it. Am I imagining this? We just got our TE410 up and running, and if we could cross-connect digital channels with it, I think we'd buy another one for the remote end (instead of using the T100P we have). Searching Google ("zaptel

Obviously, there are no DS3 TDM cards that are currently compatible with Zap channels. (or are there?) Does anyone know of an inexpensive DS3 card that could perhaps be used with Asterisk if one were to try to port the Zap drivers to such a card? PCI, of course, would be the bus of choice. I think there are quite a few discouraging comments to be made on that question. Firstly, most

Are you looking for local or Long distance? What will these T1s primarily be used for(inbound/outbound, domestic, local, long distance, international) How important are per minute rates to you? how many minutes do you expect to use per month? We are in Tampa Florida and have 15 T1s from several different providers so I may be able to refer you to one if it's a match to what you're

I have a couple of questions about Digium's T1 cards, such as the TE410P. Any answers would be greatly appreciated. 1) Do they support standard T1s or are they ISDN-only? 2) Do you know of anyone offering support for configuring T1s for Digium cards, and if so at what cost? Thanks, Matthew Roth http://www.voip-info.org/tiki-index.php?page=Running%20Asterisk%20on%20Debian

Has anyone here used T1s with RBS with asterisk? Cary Fitch

Hello, We just had some new T1s turned up today to replace others that our contract has run out on and we are now getting more echo on the new T1 lines than we had on the old ones. The T1 type is 24-channel, D4/AMI SF Robbed-bit(the same as the T1s they replaced) The problem is that we are getting echo on about 10% of the calls in and out placed on these new T1s compared to less than 1% with

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Hi all, I am handed a project to setup *. The requirement is that it can handle 8 T1s. Half of the calls coming into the system will be routed to SIP extensions (with transcoding). The machine we have in our disposal is a new dual Xeon 3.2gHz server with 2g of ram and an dual 1000mb nic. Voice will be coming in from the PSTN (through 2 quad digium cards) in g711ulaw, and most of the time will

Hello, I've seen various suggestions thrown around for hardware when people ask, but can we all agree on some basic hardware recommendations for a few basic setups(and post them on a website) to make it easier for new people to avoid some of the hardware/software pitfalls when they are setting up their first systems. Something like this: (THIS IS JUST A PROPOSED LAYOUT SO PLEASE BE GENTLE)

I just installed a TE410P on a Debian Sarge system running kernel 2.6.11-1-686-smp. Zaptel and Asterisk seem to be working fine. However, I have a couple of problems with the TE410P and Zaptel. First, the TE410P is showing me red alarms on 2 of the 4 T1s. This board (the TE410P) was just moved from another machine running REL3 and all 4 T1s were working there. I don't know why only

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Hello, We use all SCSI PCI card hardware RAIDs on all 4 of our production Asterisk servers. They all have Digium quad T1 cards and they all have from 2 to 4 T1s hooked up to them. We have had no noticable problems with dropped calls/poor quality. What are you looking to do with this system? what kind of traffic will be going through these 4 T1s? MATT--- -----Original Message----- From: Deon