search for: linecod

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5

...e password 7 XXXXXXXXXXXXXXXXX ! clock timezone GMT 0 dspint DSPfarm1/0 ! ip subnet-zero no ip routing ! ! ip name-server XXX.XXX.XXX.XXX ! no ip cef isdn switch-type primary-ni call rsvp-sync voice call send-alert voice rtp send-recv ! voice service voip ! ! ! ! ! ! controller T1 1/0 framing esf linecode b8zs cablelength long 0db pri-group timeslots 1-24 ! controller T1 1/1 framing esf linecode b8zs cablelength long 0db pri-group timeslots 1-24 ! controller T1 2/0 framing esf service-type ccs-voice linecode b8zs cablelength long 0db pri-group timeslots 1-24 ! controller T1 2/1 framing...

...192.168.5.104 boot-end-marker network-clock base-rate 56k no aaa new-model ip subnet-zero ! voice class codec 10 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 4 g729r8 codec preference 6 g729ar8 ! ! no voice confirmation-tone ! controller T1 0 mode cas framing esf linecode b8zs ds0-group 1 timeslots 1-4 type e&m-wink-start fdl both ! controller T1 1 mode cas framing esf linecode b8zs ds0-group 1 timeslots 1-4 type e&m-wink-start ! ! ! interface Tunnel1 no ip address ! interface Ethernet0 ip address xx.xx.xx.xx 255.255.255.248 ! interface Serial0 no...

If you have a PRI terminated in a Cisco router talking SIP to * and would be willing to share your Cisco config, please respond. Also, I would be interested in knowing what version of IOS you are using. We are using an NM-HDV in a 3640. TIA Bruce Komito High Sierra Networks, Inc. www.servers-r-us.com (775) 236-5815

...stem Group objects. set snmp getcom "public" set snmp setcom "public" set snmp trapcom "public" set snmp trapauth enable set snmp trapevent all -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "toasterisk" set a:1 linecode b8zs set a:1 loopdetect csu set a:1:1-24 side drop set a:1:1-24 type voice set a:1:1-24 signal ls set a:2 down set a:2 fdl none set a:2 lbo 1 set a:2 framing esf set a:2 id "CAC DS1# A:2" set a:2 linecode b8zs set a:2 loopdetect csu set a:2:1-24 side drop set a:2:1-24 type voice set a:2:...

...config info for PRI's, can someone point me to PRI config info, or let me know what changes I need to make in order to bring them up, I imagine, zapata.conf and zaptel.conf will require some changes to bring the PRI up. The PRI is currently hooked up to my cisco controller T1 1/0 framing esf linecode b8zs cablelength short 110 pri-group timeslots 1-24 interface Serial1/0:23 no ip address no logging event link-status isdn switch-type primary-5ess isdn incoming-voice voice no cdp enable Regards MIKE

...0 -Setting the SNMP MIB-II System Group objects. set snmp getcom "public" set snmp setcom "public" set snmp trapcom "public" -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "CAC DS1# 01" set a:1 linecode b8zs set a:1 loopdetect on set a:1 threshold min15 uas default set a:1 threshold min15 ses default set a:1 threshold min15 es default set a:1 threshold min15 sefs default set a:1 threshold min15 les default set a:1 threshold min15 css default set a:1 threshold min15 bes default set a:1 th...

...set snmp getcom "public" set snmp setcom "public" set snmp trapcom "public" set snmp trapauth enable set snmp trapevent all set snmp trapvers 2 -Setting slot a. set a:1 up set a:1 fdl none set a:1 lbo 1 set a:1 framing esf set a:1 id "CAC DS1# A:1" set a:1 linecode b8zs set a:1 loopdetect on set a:1:1-24 side drop set a:1:1-24 type voice set a:1:1-24 signal ls set a:2 down set a:2 fdl none set a:2 lbo 1 set a:2 framing esf set a:2 id "CAC DS1# A:2" set a:2 linecode b8zs set a:2 loopdetect on set a:2:1-24 side drop set a:2:1-24 type voice set a:2:1-...

...[...] spe country t1-default isdn switch-type primary-ni ! voice hunt user-busy voice call send-alert voice call convert-discpi-to-prog voice rtp send-recv voice service voip fax protocol pass-through g711alaw h323 sip bind all source-interface FastEthernet0/0 controller T1 3/0 framing esf linecode b8zs pri-group timeslots 1-24 interface Serial3/0:23 description T1 to CLEC no ip address load-interval 30 isdn switch-type primary-ni isdn incoming-voice modem no cdp enable voice-port 3/0:D bearer-cap Speech dial-peer voice 1 pots incoming called-number 21255512[00-50] direct-inward-di...

...ected to a cisco 3640 (in my day "cisco" is all lower case :-)). My config looks something like this on the cisco... --------------------------------------------------------- voice-card 3 dsp services dspfarm ! ip cef ! isdn switch-type primary-5ess ! controller T1 3/0 framing esf linecode b8zs pri-group timeslots 1-24 description RCN PRI at SF7 ! interface FastEthernet1/0 no ip address duplex auto speed auto ! interface Serial3/0:23 no ip address dialer-group 1 isdn switch-type primary-5ess isdn incoming-voice voice no cdp enable ! voice-port 3/0:23 connection...

...port connects immediately without ringing the attached phone. If I pick up the phone, it's connected and I can talk to the caller. Hanging up has no effect. I can see the bit transitions (0101 to 1111 when I go off hook), but no dial tone. My config is: controller T1 7/1 framing esf linecode b8zs cablelength short 133 ds0-group 0 timeslots 1 type fxs-loop-start ds0-group 1 timeslots 2 type fxs-loop-start ds0-group 2 timeslots 3 type fxs-loop-start ds0-group 3 timeslots 4 type fxs-loop-start ds0-group 4 timeslots 5 type fxs-loop-start ds0-group 5 timeslots 6 type fxs-loop...

...er capacity active ! voice service pots ! voice service voip ! voice class codec 10 codec preference 1 gsmfr codec preference 2 g711alaw ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! controller T1 1/0 shutdown framing esf linecode b8zs ! ! ! interface FastEthernet0/0 ip address 192.168.65.200 255.255.255.0 duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! ip http server ip classless ip route 0.0.0.0 0.0.0.0 192.168.65.1 ! ! ! dialer-list 1 protocol ip permit ! ! call r...

...0,ccs,hdb3,crc4,yellow span=3,0,0,ccs,hdb3,crc4,yellow span=4,0,0,ccs,hdb3,crc4,yellow current i have problem error message in cisco as5300 after make a call, if used debug isdn q931 in cisco AS5300 config : isdn siwtch-type primary-net5 controller e1 0 framming crc4 linecode hdb3 pri-group 1-31 interface serial0:15 isdn switch-type primary-net5 isdn incomming-voice modem isdn T310 60000 dialpeer,.....blah,...blahh thanks for ur help Dirgan Send instant messages to your online friends http://asia.messenger.yahoo.com ---...

I see a lot of comments but no actual show runs. Can someone post a 7206 config. I am having a dickens of a time getting calls to pass. I currently have the following loaded. Cisco IOS Software, 7200 Software (C7200-IK9O3S-M), Version 12.3(8)T6, RELEASE SOFTWARE (fc2) Thanks !!! Jerry -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.344 /

...e CST -6 clock summer-time CDT recurring ! no aaa new-model ip subnet-zero no ip routing ip finger ip domain name shsu.edu ip name-server 158.135.1.20 ip name-server 158.135.1.200 ! ! isdn switch-type primary-5ess isdn voice-call-failure 0 ! ! ! ! ! ! ! ! ! ! ! ! controller T1 0 shutdown framing sf linecode ami ! controller T1 1 shutdown framing sf linecode ami ! controller T1 2 framing esf clock source line primary linecode b8zs pri-group timeslots 1-24 ! controller T1 3 shutdown framing sf linecode ami ! ! interface Ethernet0 no ip address no ip route-cache shutdown ! interface Serial2:23 no ip add...

Hi i test a new equipment on my backbone: a Cisco AS5300 with voice dsp ressource connected at a E1 Voice Link. I want that all call incoming on the cisco 5300 are sent to Asterisk and all Asterisk outgoing call are sent to Cisco AS5300. Actually, i configure the AS5300: isdn switch-type primary-net5 ! voice service voip sip ! voice class codec 400 codec preference 1 g711alaw codec

Hello, I have an Adit 600 (3 FXS cards) hooked up to a digium T1 card in my asterisk box. I 'connected' the slots to the a:1 T1 interfaces via the command line. The slots (3 fxs) are configured with 'ls' signaling. I configured the T1 card with the same line settings as the T1 interfaces on the adit and I get green lights on both the T1 card and the T1 interface on the adit (so

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

...g711ulaw codec preference 2 g711alaw codec preference 3 g723ar53 codec preference 4 g723ar63 codec preference 5 g723r53 codec preference 6 g728 codec preference 7 g729r8 ! ! ! ! ! ! ! ! ! username nvxcpe privilege 15 secret 5 $1$oAvO$zHweQ8lbhZjzROdYw4psM/ ! ! controller T1 1/0 framing esf linecode b8zs cablelength short 133 pri-group timeslots 1-8,24 description WAN ! ! ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface Serial0/0 no ip address encapsulation frame-relay IETF no ip mroute-cache no fair-queue service-module t1 timeslots 1-24 fram...

List users, It's been a while since I've posted here, but I've been hard at work pushing toward our large scale Asterisk goal and keeping up with this list can be a full time job by itself (I have19,543 unread list messages!!). This Friday, September 16th 2005, my team will be at the MCI Development Lab in Richardson, Texas testing our setup. We have a three server system