asterisk users - Nov 2006 - Sangoma A101 gives 'no PRI configured on span 1' error

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and
installation was successful. zttool, ztcfg, all show card is installed
properly. I copied the parameters from my old working zaptel.conf,
zapata.conf and zapata-auto.conf. Verified on Sangoma website that these
files are correct. Also configured wanpipe1.conf.

But doing all this didn't start the PRI channels. It says 'no PRI
configured
on span 1' on Asterisk CLI on typing 'pri show span 1'.

What am I missing here?

-- 
Zeeshan A Zakaria
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20061116/3d58662a/attachment.htm

Zeeshan Zakaria wrote:
> I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, 
> and installation was successful. zttool, ztcfg, all show card is 
> installed properly. I copied the parameters from my old working 
> zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma 
> website that these files are correct. Also configured wanpipe1.conf.
> 
> But doing all this didn't start the PRI channels. It says 'no PRI 
> configured on span 1' on Asterisk CLI on typing 'pri show span
1'.
> 
> What am I missing here?
> 
> -- 
> Zeeshan A Zakaria
Hi,

This is my .conf files  (edited for brevity)

zaptel.conf

span=1,1,0,ccs,hdb3,crc4

bchan=1-15,17-31
dchan=16

zapata.conf
switchtype=euroisdn

group=0
context=inbound
signalling=pri_net
;group=1
callerid=asreceived
channel => 1-15,17-31


wanpipe1.conf

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment

[wanpipe1]
CARD_TYPE       = AFT
S514CPU         = A
CommPort        = PRI
AUTO_PCISLOT    = NO
PCISLOT         = 1
PCIBUS          = 3
FE_MEDIA        = E1
FE_LCODE        = HDB3
FE_FRAME        = NCRC4
FE_LINE         = 1
TE_CLOCK        = NORMAL
ACTIVE_CH       = ALL
TE_HIGHIMPEDANCE        = NO
INTERFACE       = V35
CLOCKING        = EXTERNAL
BaudRate        = 0
MTU             = 1500
UDPPORT         = 9000
TTL             = 255
IGNORE_FRONT_END = NO

[w1g1]
PROTOCOL        = HDLC
HDLC_STREAMING  = NO
ACTIVE_CH       = ALL
IDLE_FLAG       = 0x7E
MTU             = 1500
MRU             = 1500
TDMV_SPAN       = 1
TDMV_ECHO_OFF   = NO
MULTICAST       = NO
TRUE_ENCODING_TYPE      = NO

[root@ecnboksburg ~]# wanrouter status

Devices currently active:
         wanpipe1


Wanpipe Config:

Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If's | CLK | Baud
rate |
wanpipe1    | N/A          | A101/2   | 201 | 1       | 1    | EXT | 0         |

Wanrouter Status:

Device name | Protocol | Station | Status        |
wanpipe1    | AFT HDLC | N/A     | Connected     |


[root@ecnboksburg ~]# wanrouter hwprobe

-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A101u  : SLOT=1 : BUS=3 : IRQ=201 : CPU=A : PORT=PRI

Card Cnt: S508=0  S514X=0  S518=0  A101-2=1  A104=0  A300=0


ecnboksburg*CLI> zap show status
Description                              Alarms     IRQ        bpviol     CRC4
wanpipe1 card 0                          OK         0          0          0




-- 
thanks,
yusuf

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.