Displaying 20 results from an estimated 29 matches for "w1g1".
Did you mean:
w11
2006 Feb 16
2
tc filter problem
...;m using a linux 2.4.29 kernel and having trouble getting my filters added. The
script I''m editing I actually use on a different system currently. Is this a
tc/iproute/kernel type incompatibility? Any ideas how to debug it?
Thanks, Jeremy
# create a qdisc on T1 interface
tc qdisc add dev w1g1 root handle 1: htb default 77
OK
# create a master class
tc class add dev w1g1 parent 1: classid 1:1 htb rate 1400kbit
OK
# create a leaf class
tc class add dev w1g1 parent 1:1 classid 1:10 htb rate 175kbit \
ceil 1400kbit prio 0
OK
# create a SFQ qdisc within our subclass
tc qdisc add dev...
2005 Feb 17
2
Sangoma A104 - D-Channel problem
...n (Port 1)!
wanpipe1: All channels enabled
wanpipe1: Front end successful
wanpipe1: AFT Security: UnChannelised
wanpipe1: Configuring Device :wanpipe1 FrmVr=8
wanpipe1: Global MTU = 1500
wanpipe1: Global MRU = 1500
wanpipe1: Data Mux Map = 0x76543210
wanpipe1: Configuring Interface: w1g1
wanpipe1:w1g1: Running in TDM Voice mode.
wanpipe1: AFT Fifo Level Map: 0x02082082
wanpipe1: Registering interface to Zaptel span # 1!
wanpipe1: MRU :248
wanpipe1: MTU :248
wanpipe1: HDLC Eng :Off (Transparent)
wanpipe1: Data Mux Ctrl :On
wanpipe1:w1g1: Active c...
2011 Feb 17
0
PRI "wanrouter status" shows disconnected - system problem or Telco?
...disconnected. Following are the alarms raised. Should I call telco (they
have long wait times) or should I just keep searching online for
troubleshooting tips. "*wanpipe1 | AFT TE1 | N/A | Disconnected |"
<<<<<* This is what shows.
root at pbx:~ $ wanpipemon -i w1g1 -c Ta
***** w1g1: T1 Rx Alarms (Framer) *****
*ALOS: OFF | LOS: ON*
*RED: ON | AIS: OFF*
*LOF: ON | RAI: OFF*
*
*
****** w1g1: T1 Rx Alarms (LIU) ******
*
*
*Short Circuit: OFF*
*Open Circuit: OFF*
*Loss of Signal: ON*
***** w1g1: T1 Tx Alarms *****
AIS: ON |...
2007 Dec 02
1
setting up two asterisk server as ss7 back to back.
...the write up on
http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup
I have the cross over cable between them.
however, wanpipe shows connected but the signaling link does not align.
i have my configs for host A
##wanpipe1.conf
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 4
PCIBUS = 15
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = MASTER
TE_REF_CLOCK...
2010 Oct 01
2
No translator path exists for channel type DAHDI (native 76) to 256
...| AFT TE1 | N/A | Disconnected |
wanpipe5 | AFT TE1 | N/A | Disconnected |
wanpipe6 | AFT TE1 | N/A | Disconnected |
wanpipe7 | AFT TE1 | N/A | Disconnected |
wanpipe8 | AFT TE1 | N/A | Disconnected |
root at Sangoma-Testing:/etc/asterisk# wanpipemon -i w1g1 -c Ta
***** w1g1: E1 Alarms (Framer) *****
ALOS: OFF | LOS: OFF
RED: OFF | AIS: OFF
OOF: OFF | RAI: OFF
***** w1g1: E1 Alarms (LIU) *****
Short Circuit: OFF
Open Circuit: OFF
Loss of Signal: OFF
***** w1g1: E1 Performance Monitoring Counters *****
Line Cod...
2011 Feb 11
2
sangoma wanpipe install error
...config: WAN device wanpipe1 driver load failed !!
: ioctl(wanpipe1,ROUTER_SETUP) failed:
: 22 - Invalid argument
Wanpipe driver did not load properly
Please check /var/log/wanrouter and
/var/log/messages for errors
Configuring interfaces: w1g1 w1g1: ERROR while getting interface flags: No
such device
done.
/etc/wanpipe/scripts/start: 7: Syntax error: Bad for loop variable
DAHDI_SPANCONFIG failed on span 1: No such device
or address (6)
Dont know why I still keep getting a 'No such device' error even if the
device was detected...
2010 Apr 01
2
Problem with Sangoma A104 and euroisdn pri
...nfiguration files and debugging output:
==begin zaptel.conf ====================
loadzone=us
defaultzone=us
span=1,0,0,ccs,hdb3
bchan=1-15,17-31
hardhdlc=16
==end zaptel.conf ======================
==begin wanpipe1.conf ==================
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 4
PCIBUS = 13
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = NORMAL...
2008 Nov 19
1
dahdi_test drops after restarting Sangoma driver
...ce: 99.996683
[root at sitges bin]# service wanrouter stop
Shutting down asterisk: [ OK ]
Stopping Asterisk...
Shutting down wanpipe4 interface: w4g1
Shutting down wanpipe3 interface: w3g1
Shutting down wanpipe2 interface: w2g1
Shutting down wanpipe1 interface: w1g1
Shutting down device: wanpipe4
Shutting down device: wanpipe3
Shutting down device: wanpipe2
Shutting down device: wanpipe1
No devices running, Unloading Modules
[root at sitges bin]# service wanrouter start
Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
--...
2005 Sep 27
4
BAD echo problems with Sangoma and Telstra
...rn=no
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
adsi=no
callprogress=no
switchtype => euroisdn
signalling => pri_cpe
callgroup => 1
group => 1
immediate => no
channel => 1-10
##EOF
##/etc/wanpipe/wanpipe1.conf
[devices]
wanpipe1 = WAN_AFT, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 0
PCIBUS = 1
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK =...
2007 Aug 06
4
low-level dump for PRI dchan debugging
...now dms100 for the
switchtype. The telco tech I've been working with says that he's been
sending "reset all channels" signals to my system, to which he's
getting an "establish remote" response from my asterisk box. I've
been running a packet dump (wanpipemon -i w1g1 -c trd) of my d-channel
this whole time and have yet to see a single incoming packet. I
believe I *should* be seeing an incoming packet when he sends the
reset, correct? Is there any way to do a completely raw dump of the
d-channel?
Here are my specs:
linux-2.6.16
libpri-1.3.5
zaptel-1.2.19
aste...
2007 Jul 26
1
Asterisk 1.2.23 and Sangoma a102 no incoming calldetected
...DSS1
However if I configure the card for CAS, it will never connect.
My card is currently configured (and makes only outgoing calls) as:
E1 PRI, CCS, HDB3,NCRC4 (i have no idea what dss1 is or where it goes)
My /etc/wanpipe/wanpipe1.conf is:
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 1
PCIBUS = 4
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK...
2005 Sep 05
0
Re: Asterisk-Users Digest, Vol 14, Issue 22
...rogram.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = YES
PCISLOT = 2
PCIBUS = 1
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK = 0
ACTIVE_CH = ALL
TE_HIGHIMPEDANCE = YES
FE_TXTRISTATE = NO
MTU =...
2005 May 15
0
Re: Asterisk-Users Digest, Vol 10, Issue 114
...rogram.
#
# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = YES
PCISLOT = 1
PCIBUS = 1
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = NORMAL
ACTIVE_CH = ALL
TE_HIGHIMPEDANCE = NO
INTERFACE = V35
CLOCKING = EXTERNAL
BaudRate =...
2007 Jul 26
1
Asterisk 1.2.23 and Sangoma a102 no incoming call detected
...DSS1
However if I configure the card for CAS, it will never connect.
My card is currently configured (and makes only outgoing calls) as:
E1 PRI, CCS, HDB3,NCRC4 (i have no idea what dss1 is or where it goes)
My /etc/wanpipe/wanpipe1.conf is:
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 1
PCIBUS = 4
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = NCRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK...
2010 Jul 29
1
Problem with Sangoma card...
I have a problem with a Sangoma card. It worked until yesterday. Now
I keep getting this error:
Jul 29 17:45:17 pbxacura kernel: wanpipe1: Enable E1 CAS signalling
mode!
Jul 29 17:45:17 pbxacura kernel: wanpipe1:w1g1: Rx Error: No
'DeviceSelect' from target: pci fatal error! (0x000FA000)
Jul 29 17:45:48 pbxacura last message repeated 30946 times
It is using Wanpipe 3.5.6 and Zaptel 1.4.12.1 with Asterisk 1.4.30 and
MFC/R2. The E1 shows Tx side blocked and no calls in or out. I
reinstalled Wanpipe an...
2005 Apr 30
8
Problem with Sangoma/Adtran 600 installation
I have installed Asterisk on a CentOS4 box and then installed Asterisk from
CVS.
I installed a Sangoma A101 and connected it to a Adtran 600 using a T1
Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces.
I ran through the wanpipe install instructions and configured it, now I can
run
[root@altpbx asterisk]# wanrouter hwprobe
-------------------------------
| Wanpipe Hardware Probe Info
2006 Nov 16
1
Sangoma A101 gives 'no PRI configured on span 1' error
I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and
installation was successful. zttool, ztcfg, all show card is installed
properly. I copied the parameters from my old working zaptel.conf,
zapata.conf and zapata-auto.conf. Verified on Sangoma website that these
files are correct. Also configured wanpipe1.conf.
But doing all this didn't start the PRI channels. It says
2007 Jul 03
1
Distinctive ring detection not detecting ring cadences
...# If you want to edit this file, it is
# recommended that you use wancfg program
# to do so.
#================================================
# Sangoma Technologies Inc.
#================================================
[devices]
wanpipe1 = WAN_AFT_ANALOG, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 6
PCIBUS = 1
FE_MEDIA = FXO/FXS
TDMV_LAW = MULAW
TDMV_OPERMODE = FCC
MTU = 1500
UDPPORT = 9000
TTL...
2011 Mar 23
1
Sangoma A102D wanpiple issue with dahdi
...ample:/etc/asterisk# /etc/init.d/dahdi stop
Unloading DAHDI hardware modules: ERROR: Module wanpipe is in use
ERROR: Module dahdi_echocan_mg2 is in use
ERROR: Module dahdi is in use by dahdi_echocan_mg2,wanpipe
error
root at example:/etc/asterisk# wanrouter stop
Shutting down wanpipe1 interface: w1g1
Shutting down device: wanpipe2
Shutting down device: wanpipe1
wanconfig: WAN device wanpipe1 did not shutdown
: ioctl(wanpipe1,ROUTER_DOWN) failed:
: 16 - Device or resource busy
If you router was not running ignore this message
!! Oth...
2008 Oct 06
2
Conneting Asterisk to Swyx pri
...of swyx since we're tied down by limiting software and excessive
licensing costs.
Thanks!
Geraint
pri show spans shows all spans as up and active.
zap show status shows all as ok
wanrouter status shows all as connected
wanpipe1 and 2:
[devices]
wanpipe1 = WAN_AFT_TE1, Comment
[interfaces]
w1g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
CARD_TYPE = AFT
S514CPU = A
CommPort = PRI
AUTO_PCISLOT = NO
PCISLOT = 1
PCIBUS = 16
FE_MEDIA = E1
FE_LCODE = HDB3
FE_FRAME = CRC4
FE_LINE = 1
TE_CLOCK = NORMAL
TE_REF_CLOCK...