Hi, I have a 1 port T1 card in an asus p4p800-vm board with a 2.0g Celeron, and 512m of 266mhz ram (256 on each channel). This board has video, Ethernet, and serial ata all on-board, I got it because of that, there wouldn't be anything else on the pci bus that would mess with the zaptel card(s). So, here's my problem. I'm running redhat 9 with kernel 2.4.20-20.9. I can load the zaptel module fine. I can also load the wct1xxp module fine. But, after I load the wct1xxp module, I notice that the entire box just freezes for about 3 seconds every 30 seconds. Zttool sees the card fine, doesn't see any problems (other than the circuit down), and there are no irq misses. Within 3 seconds of starting *, the entire box just hangs, and never recovers. The only other thing on the same pci bus as the t1 card is the onboard Ethernet controller, and nothing is sharing its irq (5). I also tried messing with the pci latency timer. The default was 64, I tried 32, 64, 96, and 128. I did notice though, as the numbers got smaller, the time the system was frozen and the interval of the freezing became shorter (ie 64 was twice as long as 32). Just to try it, I removed the span config for this card from zaptel.conf, and wa-la, no more freezing, but then my card wasn't configured at all. * would then start, but its pointless then. This is a new box, and I've never been able to get this to work. Any ideas? -Joe
On Thu, 2003-09-11 at 12:21, Joe Antkowiak wrote:> Hi, > > I have a 1 port T1 card in an asus p4p800-vm board with a 2.0g Celeron, and > 512m of 266mhz ram (256 on each channel). This board has video, Ethernet, > and serial ata all on-board, I got it because of that, there wouldn't be > anything else on the pci bus that would mess with the zaptel card(s).While these devices may not be cards plugged into the PCI bus, it is most likely the same PCI bus. Do a lspci and post the results and we will be able to point out how you tell they are on the same PCI bus.> So, here's my problem. I'm running redhat 9 with kernel 2.4.20-20.9. I can > load the zaptel module fine. I can also load the wct1xxp module fine. But, > after I load the wct1xxp module, I notice that the entire box just freezes > for about 3 seconds every 30 seconds. Zttool sees the card fine, doesn't > see any problems (other than the circuit down), and there are no irq misses. > Within 3 seconds of starting *, the entire box just hangs, and never > recovers.send a copy of your /proc/interupts file too.> The only other thing on the same pci bus as the t1 card is the onboard > Ethernet controller, and nothing is sharing its irq (5). I also tried > messing with the pci latency timer. The default was 64, I tried 32, 64, 96, > and 128. I did notice though, as the numbers got smaller, the time the > system was frozen and the interval of the freezing became shorter (ie 64 was > twice as long as 32). > > Just to try it, I removed the span config for this card from zaptel.conf, > and wa-la, no more freezing, but then my card wasn't configured at all. * > would then start, but its pointless then. > > This is a new box, and I've never been able to get this to work. Any > ideas? > > -Joe > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users-- Steven Critchfield <critch@basesys.com>
I have the box powered down atm, and I'm not on site, but the only thing sitting on 5 is "t1xxp" -----Original Message----- From: Steven Critchfield <critch@basesys.com> Date: Thu, 11 Sep 2003 13:50:13 -0500 To: asterisk-users@lists.digium.com <asterisk-users@lists.digium.com> Subject: Re: [Asterisk-Users] Is my card bad? On Thu, 2003-09-11 at 12:21, Joe Antkowiak wrote:> Hi, > > I have a 1 port T1 card in an asus p4p800-vm board with a 2.0g Celeron, and > 512m of 266mhz ram (256 on each channel). This board has video, Ethernet, > and serial ata all on-board, I got it because of that, there wouldn't be > anything else on the pci bus that would mess with the zaptel card(s).While these devices may not be cards plugged into the PCI bus, it is most likely the same PCI bus. Do a lspci and post the results and we will be able to point out how you tell they are on the same PCI bus.> So, here's my problem. I'm running redhat 9 with kernel 2.4.20-20.9. I can > load the zaptel module fine. I can also load the wct1xxp module fine. But, > after I load the wct1xxp module, I notice that the entire box just freezes > for about 3 seconds every 30 seconds. Zttool sees the card fine, doesn't > see any problems (other than the circuit down), and there are no irq misses. > Within 3 seconds of starting *, the entire box just hangs, and never > recovers.send a copy of your /proc/interupts file too.> The only other thing on the same pci bus as the t1 card is the onboard > Ethernet controller, and nothing is sharing its irq (5). I also tried > messing with the pci latency timer. The default was 64, I tried 32, 64, 96, > and 128. I did notice though, as the numbers got smaller, the time the > system was frozen and the interval of the freezing became shorter (ie 64 was > twice as long as 32). > > Just to try it, I removed the span config for this card from zaptel.conf, > and wa-la, no more freezing, but then my card wasn't configured at all. * > would then start, but its pointless then. > > This is a new box, and I've never been able to get this to work. Any > ideas? > > -Joe > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users-- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users
Hi, I am using Cisco 7940/7960 phones with * using a T100P card that is fed from an Adtran TSU 600. I am getting the CallerID phone number, but no name. Is there a setting I am missing the * config files? Thanks, Travis Microserv