similar to: Is my card bad?

Just cross pairs 1-2 and 4-5 1 <--> 4 2 <--> 5 Never done an E1, but I think it's the same for a T1 4 wire cable. Tim Thompson Commercial Sales Engineer http://www.amatechtel.com (806) 722-2227 -----Original Message----- From: bam [mailto:bam@cqm.co.uk] Sent: Monday, December 29, 2003 9:12 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] E100P pinouts

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

Are there any known issues with putting 2 4-port T1 cards in a single box and having all ports and all channels in use at the same time? Planning on 4 of these boxes, dual AMD cpu MB from MSI, 512m, redhat 9, agp video, on board NICs, serial ata raid. Any input would be appreciated. -Joe

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

Hi, i just received an E100P, this is the first one I have ever seen, and notice that the board reads T100P. Is this right ? The antistatic bag had a small label that has E100P written on it, and the card is a bit different than the T100P I already have, Does Digium use the same boards for both cards ? I don't have an E1 link here, can I test the card just by loading the driver and run

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040913/52b2ac04/attachment.htm -------------- next part -------------- hi all, can anyone give solution for this. ?wct1xxp - Digium Wildcard T100P T1/PRI Card 0 zttool gives RED Digium Wildcard T100P T1/PRI Card 0 my zaptel.conf look like this span=1,1,0,esf,b8zs

Hi, all I am trying to install E100P card, the 'modprobe zaptel' is ok, but when I did 'modprobe wct1xxp', I got such error, so can not load the driver for the card. /lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog

Hi All, I wish to connect * to a Cisco using a E100P board. When I load the driver I got this error message: -bash-2.05b# modprobe wct1xxp ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows Cisco configuration: isdn switch-type primary-qsig

Hi, I am trying to set up * and ISDN-PRI (channels 1 - 15) using E100 boards. I installed zaptel and libpri. When I execute modprobe -r wct1xxp I get an error message: ZT_CHANCONFIG failed on channel 1: Function not implemented (38) /lib/modules/2.4.21-SAX/misc/wct1xxp.o: post-install wct1xxp failed /lib/modules/2.4.21-SAX/misc/wct1xxp.o: insmod wct1xxp failed Follows my /etc/zaptel.conf:

Hi guys, Thanks for your answers on my two questions yesterday. That's exactly what I was looking for, sorry for not noticing it myself, but I'm still getting acclimated to Asterisk and even Linux--from what I see so far, I love it. I've got another one now. Since my Asterisk install and configuration is fairly stable at this point, I'm interested it ensuring that during

i have error in install module of tor2. but it compile good. what happen ? ivr2:/usr/src/zaptel # make clean; make install rm -f torisatool makefw tor2fw.h rm -f zttool rm -f *.o ztcfg tzdriver sethdlc rm -f zonedata.lo tonezone.lo libtonezone.so.1.0 *.lo rm -f gendigits tones.h rm -f libtonezone* rm -f tor2ee rm -f core cc -I. -O4 -g -Wall -DBUILDING_TONEZONE -DSTANDALONE_ZAPATA -c -o

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040913/22b214e9/attachment.htm -------------- next part -------------- hi all, can anyone give solution for this. ?wct1xxp - Digium Wildcard T100P T1/PRI Card 0 zttool gives RED Digium Wildcard T100P T1/PRI Card 0 my zaptel.conf look like this span=1,1,0,esf,b8zs

We connected an * box with an e100p to an E1/PRI from a telco here in Italy. After we had it working perfectly the telco told us that, despite the circuit appeared to work fine, and we could place calls on it, they had an "E-bit2 alarm indication constantly on that caused the circuit to be flagged as "faulty" every time. (The E-bit indication, is an alarm sent back from us to

Hi, I try to connect my asterisk box with a classic pbx (Siemens). I have a T100P E1 card. modprobe zaptel and wct1xxp ok ztcfg -vv ok I can run asterisk and show the channels but the led still flash red My zaptel.conf : span=1,1,0,ccs,hdb3,crc4 bchan=1-15 bchan=17-31 dchan=16 My zapata.conf : ;; E1 switchtype = euroisdn signalling = pri_net group = 1 context=e1 channel => 1-15,17-31

hi all i have a te110p installed in my system with a lot of Echo.. i decide to install the oslec echo supressor but when y try to add the module i have this problem. [root at asterisk zaptel-1.4.7.1]# insmod wct1xxp.ko insmod: error inserting 'wct1xxp.ko': -1 Unknown symbol in module [root at asterisk zaptel-1.4.7.1]# some advice? thanks. -- .-

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hello! I have problems compiling zaptel (tried 1.2.11, 1.2.10 and 1.4.0-beta2 -- all give the same error) with 2.6.19 kernel CC [M] /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.o In file included from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/xpd.h:26, from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.c:28:

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hello, I need help to install a digium card TC400P. I compiled the dahdi source, but dahdi don?t find the card! debian:/usr/src/dahdi-linux-complete-2.2.0.2+2.2.0# lspci 11:03.0 Ethernet controller: Digium, Inc. Wildcard TC400P transcoder base card (rev 11) debian:/usr/src/dahdi-linux-complete-2.2.0.2+2.2.0# /etc/init.d/dahdi restart Unloading DAHDI hardware modules:

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the