Hello,
I have following problem with Sangoma A104 card:
CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on
Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on
Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on
Primary D-channel of span 1
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on
Primary D-channel of span 1
Any idea how to fix it?
My configs:
zaptel.conf:
span=1,1,1,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
zapata.conf
[channels]
switchtype=euroisdn
pridialplan=unknown
overlapdial=no
usecallerid=yes
hidecallerid=yes
callwaiting=no
callwaitingcallerid=no
threewaycalling=no
transfer=no
cancallforward=no
callreturn=no
jitterbuffers=4
echocancel=yes
echocancelwhenbridged=no
echotraining=yes
relaxdtmf=yes
rxgain=0.5
txgain=0.9
immediate=no
amaflags=billing
adsi=no
busydetect=no
callprogress=no
context = zapline1
switchtype = euroisdn
group=1
signalling = pri_cpe
channel => 1-15
channel => 17-31
cat /proc/zaptel/1 :
Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4
1 WPE1/0/1 Clear (In use)
2 WPE1/0/2 Clear (In use)
3 WPE1/0/3 Clear (In use)
4 WPE1/0/4 Clear (In use)
5 WPE1/0/5 Clear (In use)
6 WPE1/0/6 Clear (In use)
7 WPE1/0/7 Clear (In use)
8 WPE1/0/8 Clear (In use)
9 WPE1/0/9 Clear (In use)
10 WPE1/0/10 Clear (In use)
11 WPE1/0/11 Clear (In use)
12 WPE1/0/12 Clear (In use)
13 WPE1/0/13 Clear (In use)
14 WPE1/0/14 Clear (In use)
15 WPE1/0/15 Clear (In use)
16 WPE1/0/16 HDLCFCS (In use)
17 WPE1/0/17 Clear (In use)
18 WPE1/0/18 Clear (In use)
19 WPE1/0/19 Clear (In use)
20 WPE1/0/20 Clear (In use)
21 WPE1/0/21 Clear (In use)
22 WPE1/0/22 Clear (In use)
23 WPE1/0/23 Clear (In use)
24 WPE1/0/24 Clear (In use)
25 WPE1/0/25 Clear (In use)
26 WPE1/0/26 Clear (In use)
27 WPE1/0/27 Clear (In use)
28 WPE1/0/28 Clear (In use)
29 WPE1/0/29 Clear (In use)
30 WPE1/0/30 Clear (In use)
31 WPE1/0/31 Clear (In use)
Information from dmesg:
Processing WAN device wanpipe1...
wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0
wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0
PCI: Found IRQ 10 for device 00:08.0
wanpipe1: AFT PCI memory at 0xEE000000
wanpipe1: IRQ 10 allocated to the AFT PCI card
wanpipe1: Initializing for SMP
wanpipe1: Starting AFT Quad Hardware Init.
wanpipe1: Enabling front end link monitor
wanpipe1: Global Chip Configuration: used=1
wanpipe1: Global Front End Configuraton!
wanpipe1: T1/E1/J1 Global configuration!
wanpipe1: AFT Data Mux Bit Map: 0x76543210
wanpipe1: Setting E1 configuration (Port 1)!
wanpipe1: All channels enabled
wanpipe1: Front end successful
wanpipe1: AFT Security: UnChannelised
wanpipe1: Configuring Device :wanpipe1 FrmVr=8
wanpipe1: Global MTU = 1500
wanpipe1: Global MRU = 1500
wanpipe1: Data Mux Map = 0x76543210
wanpipe1: Configuring Interface: w1g1
wanpipe1:w1g1: Running in TDM Voice mode.
wanpipe1: AFT Fifo Level Map: 0x02082082
wanpipe1: Registering interface to Zaptel span # 1!
wanpipe1: MRU :248
wanpipe1: MTU :248
wanpipe1: HDLC Eng :Off (Transparent)
wanpipe1: Data Mux Ctrl :On
wanpipe1:w1g1: Active channels = 0xFFFFFFFE
wanpipe1:w1g1: Setting first time slot to 1
wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248
wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off
upgrade to the following wanpipe and also upgrade the firmware o the crd (it's included in the wanpipe softwaare) ftp://ftp.sangoma.com/linux/custom/2.3.2/wanpipe-beta5g-2.3.2.tgz On Thu, 17 Feb 2005 16:07:54 +0100, Kumak <kumak@exe.pl> wrote:> > Hello, > I have following problem with Sangoma A104 card: > > CLI> pri show span 1 > Primary D-channel: 16 > Status: Provisioned, Down, Active > Switchtype: EuroISDN > Type: CPE > Window Length: 0/7 > Sentrej: 0 > SolicitFbit: 0 > Retrans: 0 > Busy: 0 > Overlap Dial: 0 > T200 Timer: 1000 > T203 Timer: 10000 > T305 Timer: 30000 > T308 Timer: 4000 > T313 Timer: 4000 > N200 Counter: 3 > > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 > NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 > > Any idea how to fix it? > > My configs: > > zaptel.conf: > > span=1,1,1,ccs,hdb3,crc4 > bchan=1-15,17-31 > dchan=16 > > zapata.conf > > [channels] > switchtype=euroisdn > pridialplan=unknown > overlapdial=no > usecallerid=yes > hidecallerid=yes > callwaiting=no > callwaitingcallerid=no > threewaycalling=no > transfer=no > cancallforward=no > callreturn=no > jitterbuffers=4 > echocancel=yes > echocancelwhenbridged=no > echotraining=yes > relaxdtmf=yes > rxgain=0.5 > txgain=0.9 > immediate=no > amaflags=billing > adsi=no > busydetect=no > callprogress=no > context = zapline1 > switchtype = euroisdn > group=1 > signalling = pri_cpe > channel => 1-15 > channel => 17-31 > > cat /proc/zaptel/1 : > > Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4 > > 1 WPE1/0/1 Clear (In use) > 2 WPE1/0/2 Clear (In use) > 3 WPE1/0/3 Clear (In use) > 4 WPE1/0/4 Clear (In use) > 5 WPE1/0/5 Clear (In use) > 6 WPE1/0/6 Clear (In use) > 7 WPE1/0/7 Clear (In use) > 8 WPE1/0/8 Clear (In use) > 9 WPE1/0/9 Clear (In use) > 10 WPE1/0/10 Clear (In use) > 11 WPE1/0/11 Clear (In use) > 12 WPE1/0/12 Clear (In use) > 13 WPE1/0/13 Clear (In use) > 14 WPE1/0/14 Clear (In use) > 15 WPE1/0/15 Clear (In use) > 16 WPE1/0/16 HDLCFCS (In use) > 17 WPE1/0/17 Clear (In use) > 18 WPE1/0/18 Clear (In use) > 19 WPE1/0/19 Clear (In use) > 20 WPE1/0/20 Clear (In use) > 21 WPE1/0/21 Clear (In use) > 22 WPE1/0/22 Clear (In use) > 23 WPE1/0/23 Clear (In use) > 24 WPE1/0/24 Clear (In use) > 25 WPE1/0/25 Clear (In use) > 26 WPE1/0/26 Clear (In use) > 27 WPE1/0/27 Clear (In use) > 28 WPE1/0/28 Clear (In use) > 29 WPE1/0/29 Clear (In use) > 30 WPE1/0/30 Clear (In use) > 31 WPE1/0/31 Clear (In use) > > Information from dmesg: > > Processing WAN device wanpipe1... > wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0 > wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0 > PCI: Found IRQ 10 for device 00:08.0 > wanpipe1: AFT PCI memory at 0xEE000000 > wanpipe1: IRQ 10 allocated to the AFT PCI card > wanpipe1: Initializing for SMP > wanpipe1: Starting AFT Quad Hardware Init. > wanpipe1: Enabling front end link monitor > wanpipe1: Global Chip Configuration: used=1 > wanpipe1: Global Front End Configuraton! > wanpipe1: T1/E1/J1 Global configuration! > wanpipe1: AFT Data Mux Bit Map: 0x76543210 > wanpipe1: Setting E1 configuration (Port 1)! > wanpipe1: All channels enabled > wanpipe1: Front end successful > wanpipe1: AFT Security: UnChannelised > wanpipe1: Configuring Device :wanpipe1 FrmVr=8 > wanpipe1: Global MTU = 1500 > wanpipe1: Global MRU = 1500 > wanpipe1: Data Mux Map = 0x76543210 > wanpipe1: Configuring Interface: w1g1 > wanpipe1:w1g1: Running in TDM Voice mode. > wanpipe1: AFT Fifo Level Map: 0x02082082 > wanpipe1: Registering interface to Zaptel span # 1! > wanpipe1: MRU :248 > wanpipe1: MTU :248 > wanpipe1: HDLC Eng :Off (Transparent) > wanpipe1: Data Mux Ctrl :On > wanpipe1:w1g1: Active channels = 0xFFFFFFFE > wanpipe1:w1g1: Setting first time slot to 1 > wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248 > wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >-- Michal Bielicki http://www.asterisk.com.pl/
Hi, Did you tried to set your DMA or SATA as described at message "Sangoma A102 cards testing FIXED"? Daniel Kumak wrote:>Hello, >I have following problem with Sangoma A104 card: > >CLI> pri show span 1 >Primary D-channel: 16 >Status: Provisioned, Down, Active >Switchtype: EuroISDN >Type: CPE >Window Length: 0/7 >Sentrej: 0 >SolicitFbit: 0 >Retrans: 0 >Busy: 0 >Overlap Dial: 0 >T200 Timer: 1000 >T203 Timer: 10000 >T305 Timer: 30000 >T308 Timer: 4000 >T313 Timer: 4000 >N200 Counter: 3 > >NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 >NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 >NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 >NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 > >Any idea how to fix it? > >My configs: > >zaptel.conf: > >span=1,1,1,ccs,hdb3,crc4 >bchan=1-15,17-31 >dchan=16 > >zapata.conf > >[channels] >switchtype=euroisdn >pridialplan=unknown >overlapdial=no >usecallerid=yes >hidecallerid=yes >callwaiting=no >callwaitingcallerid=no >threewaycalling=no >transfer=no >cancallforward=no >callreturn=no >jitterbuffers=4 >echocancel=yes >echocancelwhenbridged=no >echotraining=yes >relaxdtmf=yes >rxgain=0.5 >txgain=0.9 >immediate=no >amaflags=billing >adsi=no >busydetect=no >callprogress=no >context = zapline1 >switchtype = euroisdn >group=1 >signalling = pri_cpe >channel => 1-15 >channel => 17-31 > >cat /proc/zaptel/1 : > >Span 1: WPE1/0 "wanpipe1 card 0" HDB3//CRC4 > > 1 WPE1/0/1 Clear (In use) > 2 WPE1/0/2 Clear (In use) > 3 WPE1/0/3 Clear (In use) > 4 WPE1/0/4 Clear (In use) > 5 WPE1/0/5 Clear (In use) > 6 WPE1/0/6 Clear (In use) > 7 WPE1/0/7 Clear (In use) > 8 WPE1/0/8 Clear (In use) > 9 WPE1/0/9 Clear (In use) > 10 WPE1/0/10 Clear (In use) > 11 WPE1/0/11 Clear (In use) > 12 WPE1/0/12 Clear (In use) > 13 WPE1/0/13 Clear (In use) > 14 WPE1/0/14 Clear (In use) > 15 WPE1/0/15 Clear (In use) > 16 WPE1/0/16 HDLCFCS (In use) > 17 WPE1/0/17 Clear (In use) > 18 WPE1/0/18 Clear (In use) > 19 WPE1/0/19 Clear (In use) > 20 WPE1/0/20 Clear (In use) > 21 WPE1/0/21 Clear (In use) > 22 WPE1/0/22 Clear (In use) > 23 WPE1/0/23 Clear (In use) > 24 WPE1/0/24 Clear (In use) > 25 WPE1/0/25 Clear (In use) > 26 WPE1/0/26 Clear (In use) > 27 WPE1/0/27 Clear (In use) > 28 WPE1/0/28 Clear (In use) > 29 WPE1/0/29 Clear (In use) > 30 WPE1/0/30 Clear (In use) > 31 WPE1/0/31 Clear (In use) > > >Information from dmesg: > >Processing WAN device wanpipe1... >wanpipe1: Locating: A104 card, CPU A, PciSlot=8, PciBus=0 >wanpipe1: Found: A104 card, CPU A, PciSlot=8, PciBus=0, Port=0 >PCI: Found IRQ 10 for device 00:08.0 >wanpipe1: AFT PCI memory at 0xEE000000 >wanpipe1: IRQ 10 allocated to the AFT PCI card >wanpipe1: Initializing for SMP >wanpipe1: Starting AFT Quad Hardware Init. >wanpipe1: Enabling front end link monitor >wanpipe1: Global Chip Configuration: used=1 >wanpipe1: Global Front End Configuraton! >wanpipe1: T1/E1/J1 Global configuration! >wanpipe1: AFT Data Mux Bit Map: 0x76543210 >wanpipe1: Setting E1 configuration (Port 1)! >wanpipe1: All channels enabled >wanpipe1: Front end successful >wanpipe1: AFT Security: UnChannelised >wanpipe1: Configuring Device :wanpipe1 FrmVr=8 >wanpipe1: Global MTU = 1500 >wanpipe1: Global MRU = 1500 >wanpipe1: Data Mux Map = 0x76543210 >wanpipe1: Configuring Interface: w1g1 >wanpipe1:w1g1: Running in TDM Voice mode. >wanpipe1: AFT Fifo Level Map: 0x02082082 >wanpipe1: Registering interface to Zaptel span # 1! >wanpipe1: MRU :248 >wanpipe1: MTU :248 >wanpipe1: HDLC Eng :Off (Transparent) >wanpipe1: Data Mux Ctrl :On >wanpipe1:w1g1: Active channels = 0xFFFFFFFE >wanpipe1:w1g1: Setting first time slot to 1 >wanpipe1:w1g1: Config for Transparent mode: Idle=0 Len=248 >wanpipe1:w1g1: Allocating 65 dma skb len=256 Chaining=Off > > >_______________________________________________ >Asterisk-Users mailing list >Asterisk-Users@lists.digium.com >http://lists.digium.com/mailman/listinfo/asterisk-users >To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > > > >