asterisk users - Feb 2011 - PRI "wanrouter status" shows disconnected - system problem or Telco?

Hi everyone,

I am reading through Sangoma Wiki right now. But someone may already and
quickly notice this. I have a system that is down since the morning (maybe
power intruptions). All seems fine except for "wanrouter status" shows
disconnected. Following are the alarms raised. Should I call telco (they
have long wait times) or should I just keep searching online for
troubleshooting tips. "*wanpipe1    | AFT TE1  | N/A     | Disconnected 
|"
<<<<<* This is what shows.



root at pbx:~ $ wanpipemon -i w1g1 -c Ta

***** w1g1: T1 Rx Alarms (Framer) *****

*ALOS:   OFF     | LOS:  ON*
*RED:    ON      | AIS:  OFF*
*LOF:    ON      | RAI:  OFF*
*
*
****** w1g1: T1 Rx Alarms (LIU) ******
*
*
*Short Circuit:  OFF*
*Open Circuit:   OFF*
*Loss of Signal: ON*

***** w1g1: T1 Tx Alarms *****

AIS:    ON      | YEL:  ON


***** w1g1: T1 Performance Monitoring Counters *****

Line Code Violation     : 0
Bit Errors (CRC6/Ft/Fs) : 0
Out of Frame Errors     : 0


Rx Level        : < -36db


root at pbx:~ $ ifconfig
w1g1      Link encap:Point-to-Point Protocol
          UP POINTOPOINT NOARP  MTU:8  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:4383
          collisions:0 txqueuelen:100
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:177 Memory:f8c50000-f8c51fff

root at pbx:~ $ wanrouter hwprobe verbose

-----------------------------------------
| Wanpipe Hardware Probe Info (verbose) |
-----------------------------------------
1 . AFT-A101-SH : SLOT=4 : BUS=4 : IRQ=9 : CPU=A : PORT=1 : HWEC=32 : V=36
+01:DS26521: PCIe: PLX2

Card Cnt: A101-2=1

root at pbx:~ $ wanrouter status

Devices currently active:
        wanpipe1


Wanpipe Config:

Device name | Protocol Map | Adapter  | IRQ | Slot/IO | If's | CLK | Baud
rate |
wanpipe1    | N/A          | A101/1D/A102/2D/4/4D/8| 177 | 4       | 1    |
N/A | 0         |

Wanrouter Status:

Device name | Protocol | Station | Status        |
*wanpipe1    | AFT TE1  | N/A     | Disconnected  |*


*pbx*CLI> pri show span 1*
Primary D-channel: 24
Status: Provisioned, In Alarm, Down, Active
Switchtype: National ISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
Logical Channel Mapping: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T309 Timer: -1
T313 Timer: 4000
N200 Counter: 3




Thanks,
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://lists.digium.com/pipermail/asterisk-users/attachments/20110217/102d55c9/attachment.htm>