Ok I know I'm not the only one having echo problem with asterisk but the weird thing is that when I receive a call from a PSTN line on my TDM04B card I don't have any echo problem at the beginning of the call then after a few minutes I start having echo on my side only (the person calling from a regular phone doesn't have any echo), then it stop and come back all the way until the call is finish. It does the same thing on outgoing calls from my Cisco 7960 phone to the PSTN line. I have no problem when it's an internal call from one 7960 to another one. I tried a lot of different config in zapata.conf and the one that seems to work the best for now is this one : context=incoming signalling=fxs_ks echotraining=800 echocancel=yes echocancelwhenbridged=yes rxgain=0 txgain=0 immediate=no busydetect=no callprogress-no musiconhold=default usecallerid=yes callerid=asreceived group=1 channel => 1-8 Any suggestion why it start doing echo after 5 minutes or so? Thanks Martin
> Ok I know I'm not the only one having echo problem with asterisk but the > weird thing is that when I receive a call from a PSTN line on my TDM04B > card I don't have any echo problem at the beginning of the call then after > a few minutes I start having echo on my side only> (the person calling from a regular phone doesn't have any echo),I think that's the way it usually works... (i.e., only you hear the echo).> then it stops and comes back all the way until the call is finished. It > does the same thing on outgoing calls from my Cisco 7960 phone to the PSTN > line.The echo happens when you make a call from IP to a 2-wire PSTN Phone.> I have no problem when it's an internal call from one 7960 to another one.And you shouldn't.> I tried a lot of different config in zapata.conf and the one that seems to > work the best for now is this one : > > context=incoming > signalling=fxs_ks > echotraining=800 > echocancel=yes > echocancelwhenbridged=yes > rxgain=0 > txgain=0 > immediate=no > busydetect=no > callprogress-no > musiconhold=default > usecallerid=yes > callerid=asreceived > group=1 > channel => 1-8 > > Any suggestion why it starts doing echo after 5 minutes or so?Martin, I had a similar problem, but the echo would just come and go. What are you using for your FXO ports? Do you have the echo cancel turned on when you create those channels? I'm assuming you do since your FXS ports start at one, and unless you specifically turned it off for your FXO ports, the echo cancel setting (and all other settings) will carry over from the previous channel settings. I have a T100P/PRI for my PSTN connection, and I changed the T100P card to another pci slot on the same motherboard. After that, the echo problem disappeared. I just used echocancel=yes and echotraining=yes. The default for echocancel is 128. You can change that number too. I never thought moving the cards around on the motherboard would matter, but after reading a few other posts and seeing that this fixed some other problems for people, I thought I would try it for my echo problem. In fact, my echo problem started after a support guy at Digium had me move some cards around. I erroneously attributed my new echo to the latest version of Asterisk that he installed and not to the moving of the pci cards. I have also heard that changing motherboards will change things too. But that might introduce different issues.... Regards, Brian
Yes that's what I have in my current config... : context=incoming signalling=fxs_ks echotraining=800 echocancel=yes echocancelwhenbridged=yes rxgain=0 txgain=0 immediate=no busydetect=no callprogress-no musiconhold=default usecallerid=yes callerid=asreceived group=1 callgroup=1 pickupgroup=1 channel => 1-8 |From: Rich Adamson <radamson@routers.com> | |Have you tried the following in zapata.conf? |echotraining=800 |echocancel=yes |echocancelwhenbridged=yes | |There is a remote possibility that electrical interference on the pstn |lines could impact asterisk's echo training process, but don't have a |clue how you'd measure it other then to obtain a telephony transmission |test set and actually measure the noise level.
Just wondering if someone can explain this scenario: phone--iaxy--interweb--(asterisk)--IAX2trunk--(asterisk)--SNOM360(SIP) calls work like a charm. The iaxy user (in canada) hears very clear audio, no hiss drops or echos. The snom user (me in uk) has fine audio from the iaxy but always hears an echo of himself. This is only heard on this call, all other calls are fine. So where is the echo coming from?? Thanks Bails
The analog phone on the iaxy? Tried a different phone? -----Original Message----- From: bails [mailto:bails@westcomuk.com] Sent: Thursday, December 22, 2005 9:03 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Weird Echo Problem Just wondering if someone can explain this scenario: phone--iaxy--interweb--(asterisk)--IAX2trunk--(asterisk)--SNOM360(SIP) calls work like a charm. The iaxy user (in canada) hears very clear audio, no hiss drops or echos. The snom user (me in uk) has fine audio from the iaxy but always hears an echo of himself. This is only heard on this call, all other calls are fine. So where is the echo coming from?? Thanks Bails _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users