similar to: Problems with language support

Hello everybody! I have some problems with my Astersk. I have an analogical OpenVox card and A Billion ISDN card (with mISDN). I load the modules with modprobe zaptel and modprobe wctdm. When I run ztcfg -vv I have this: Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No

How can we set the CDR Master file to rollover at say 30 Meg and create a new one -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100827/2e98385f/attachment.htm

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

For some reason Asterisk is producing a US ring tone when it should be an Australian ring tone. I am using ztdummy and do not have any cards installed. My configuration is as follows. I am using Trixbox 1.2.2. Can someone please guide me into the right direction? zaptel.conf loadzone = au defaultzone = au zapata.conf [channels] language=au indications.conf [general]

Evening, My latest asterisk box is having a difficult problem. It is configured with one TE210P and TDM400P with four FXO modules. I'm running FC6. The TE210P only has a single PRI. When the system boots, it is completely random what order the zaptel modules will get loaded in. Sometimes zttool shows the FXO as the last span, sometimes as the first. When it does load as the first, which

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

This is, hopefully, just a case of brain fade. With zapata.conf and zaptel.conf in place, asterisk loaded, no dial plan and all LEDS on the card lit, I get no dial tone, plugging an analog phone into ports 1 or 2, only a buzz and click. zaptel.conf - defaultzone=us loadzone=us fxoks=1,2 fxsks=3,4 zapata.conf [channels] signalling=fxo_ks language=us context=phones-1 group=0

Hi, I'm installing an Asterisk box with a TDM2400P in Brazil. I can make analog phones work while lines are not working. Since I do not know anything about brazilian lines, is there anybody who can tell me what is wrong/missing in my conf files (below)? TIA Giorgio _zaptel.conf:_ fxoks=9-16 fxsks=17-24 defaultzone=br loadzone=br* * _zapata.conf:_ context = inbound_zap echocancel = 128

Hi, I have installed Asterisk 1.4.20 on Debian Etch. The server has no telephony card installed, but I have anyhow installed Zaptel (Zaptel-1.4.9) in order to be able to use MeetMe. The Zaptel modules load normally. I obtain the following prompts: kerplunk:/# /etc/init.d/zaptel start Loading zaptel framework: done. Waiting for zap to come online...OK Loading zaptel hardware modules: ztdummy.

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hello About every three months, my dad's little Asterisk server that handles his business phone line with an OpenVox PCI card stops taking calls. To check if it's the cause, I'd like to run a CRON job every night to restart Zaptel and Asterisk. Before I go ahead, I'd like to know if I can just send the following commands, or if there are issues I should know about:

Greetings to all list members! My name is Aldo Sudak and I am an Asterisk newbie. I am writing now because I have not been able to find any mention to the issues described below, neither in this list nor in the wiki. I am performing preliminary tests with Asterisk 1.4.11 and Zaptel 1.4.5.1 on Fedora Core 6. Installation of all of the Asterisk packages was straightforward and I always obtained

I have an Asterisk box running Fedora Core 4, Asterisk 1.4, Lippri, 1.4, and Zaptel 1.4 The Digium cards installed are TDM2400 and TE110P. Everything was working fine until I upgraded to zaptel 1.2.12 from 1.2.9 Now when I run ztcfg I get the following error message: (CAS signalling on span 2 conflicts with Clear channel on channel 40) --NOTE: signaling was spelled wrong in the error

Running Asterisk 1.2.9. I just installed a TE110P card and configured zaptel.conf & zapata.conf. The config files look right to me but I'm getting the following error when trying to start asterisk: Asterisk died with code 1. Automatically restarting Asterisk. Does anyone have any idea what is wrong with this configuration?? Thanks in advance!!! Here's my config files: zaptel.conf

I'm trying to use a Xorcom Astribank wth Ubuntu 8.04, but got no success. I can see the channel bank with lsusb, but when I tried to use zaptel_hardware, or when I try the /etc/init.d/script, they don't see my Channel Bank. I compiled the latest Zaptel 1.4.10, with Astribank's dependecies, fxload and libusb-dev. Anyone have a similiar experience ? Best Regards, -- Guilherme Loch G?es

I'm trying to get a Qwest PRI configured and working with my lab Asterisk server. They said that the switchtype is 5ess and the signaling is pri_cpe. My entries into zaptel.conf are: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us channels=1-23 And my entries in zapata.conf are: language=en context=telco-incoming switchtype=5ess signalling=pri_cpe