Hello everybody! I have some problems with my Astersk. I have an analogical OpenVox card and A Billion ISDN card (with mISDN). I load the modules with modprobe zaptel and modprobe wctdm. When I run ztcfg -vv I have this: Zaptel Configuration ===================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address (6) And when I run asterisk -vvvc this: Jun 18 12:50:15 WARNING[2218]: chan_zap.c:1072 zt_open: Unable to specify channel 1: No such device or address Jun 18 12:50:15 ERROR[2218]: chan_zap.c:7038 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jun 18 12:50:15 ERROR[2218]: chan_zap.c:10472 setup_zap: Unable to register channel '1' Jun 18 12:50:15 WARNING[2218]: loader.c:415 __load_resource: chan_zap.so: load_module failed, returning -1 Jun 18 12:50:15 WARNING[2218]: loader.c:555 load_modules: Loading module chan_zap.so failed! My configuration files: zaptel.conf: loadzone=es defaultzone=es fxsks=1 zapata.conf: [channels] signalling=fxs_ks usecallerid=yes callwaiting=no threewaycalling=no transfer=yes cancallforward=yes echocancel=yes echotraining=yes echocancelwhenbridged=no rxgain=0 txgain=0 group=1 callgroup=1 pickupgroup=1 immediate=no faxdetect=incoming answeronpolarityswitch=yes hanguponpolarityswitch=yes polarityonanswerdelay=600 progzone=es channel => 1 I don't know what is the problem, if someone knows... Thanks and have a nice day. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070618/f07dbdfc/attachment.htm
On Mon, Jun 18, 2007 at 12:50:23PM +0200, Josu Lazkano wrote:> Hello everybody! > > I have some problems with my Astersk. I have an analogical OpenVox card and > A Billion ISDN card (with mISDN). > > I load the modules with modprobe zaptel and modprobe wctdm. > > When I run ztcfg -vv I have this: > > Zaptel Configuration > =====================> > > Channel map: > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > > 1 channels configured. > > ZT_CHANCONFIG failed on channel 1: No such device or address (6)This means your /etc/zaptel.conf is incorrect. Start by correcting it. Or maybe the driver has not loaded correctly. Which OpenVox card is it? What is the output of: lspci cat /proc/zaptel/*> zaptel.conf: > > loadzone=es > defaultzone=es > fxsks=1-- Tzafrir Cohen icq#16849755 jabber:tzafrir at jabber.org +972-50-7952406 mailto:tzafrir.cohen at xorcom.com http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir
Hello, my OpneVox card is an A400P01. And the output of lspci is: 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge 00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) 00:0c.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06) 00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) and the cat /proc/zaptel/* is: cat: /proc/zaptel/*: No such file or directory there is no files in /proc/zaptel/ thanks for all 2007/6/18, Tzafrir Cohen <tzafrir.cohen at xorcom.com>:> > On Mon, Jun 18, 2007 at 12:50:23PM +0200, Josu Lazkano wrote: > > Hello everybody! > > > > I have some problems with my Astersk. I have an analogical OpenVox card > and > > A Billion ISDN card (with mISDN). > > > > I load the modules with modprobe zaptel and modprobe wctdm. > > > > When I run ztcfg -vv I have this: > > > > Zaptel Configuration > > =====================> > > > > > Channel map: > > > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > > > > 1 channels configured. > > > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > This means your /etc/zaptel.conf is incorrect. Start by correcting it. > Or maybe the driver has not loaded correctly. > > Which OpenVox card is it? > > What is the output of: > > lspci > cat /proc/zaptel/* > > > zaptel.conf: > > > > loadzone=es > > defaultzone=es > > fxsks=1 > > -- > Tzafrir Cohen > icq#16849755 jabber:tzafrir at jabber.org > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >-------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070618/483b0abf/attachment.htm
The card is a OpenVox 2007/6/18, Josu Lazkano <jlazkano at somesi.com>:> > Hello, my OpneVox card is an A400P01. > > And the output of lspci is: > > 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host > Bridge > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge > 00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network > controller [HFC-PCI] (rev 02) > 00:0c.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06) > 00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX > Modem/ISDN interface > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge > 00:11.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev > 74) > > and the cat /proc/zaptel/* is: > > cat: /proc/zaptel/*: No such file or directory > > there is no files in /proc/zaptel/ > > thanks for all > > 2007/6/18, Tzafrir Cohen < tzafrir.cohen at xorcom.com>: > > > > On Mon, Jun 18, 2007 at 12:50:23PM +0200, Josu Lazkano wrote: > > > Hello everybody! > > > > > > I have some problems with my Astersk. I have an analogical OpenVox > > card and > > > A Billion ISDN card (with mISDN). > > > > > > I load the modules with modprobe zaptel and modprobe wctdm. > > > > > > When I run ztcfg -vv I have this: > > > > > > Zaptel Configuration > > > =====================> > > > > > > > > Channel map: > > > > > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > > > > > > 1 channels configured. > > > > > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > > > This means your /etc/zaptel.conf is incorrect. Start by correcting it. > > Or maybe the driver has not loaded correctly. > > > > Which OpenVox card is it? > > > > What is the output of: > > > > lspci > > cat /proc/zaptel/* > > > > > zaptel.conf: > > > > > > loadzone=es > > > defaultzone=es > > > fxsks=1 > > > > -- > > Tzafrir Cohen > > icq#16849755 jabber:tzafrir at jabber.org > > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > > > _______________________________________________ > > --Bandwidth and Colocation provided by Easynews.com -- > > > > asterisk-users mailing list > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > >-------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070618/2ece497d/attachment-0001.htm
On Mon, Jun 18, 2007 at 02:02:53PM +0200, Josu Lazkano wrote:> Hello, my OpneVox card is an A400P01. > > And the output of lspci is: > > 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host > Bridge > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge > 00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network > controller [HFC-PCI] (rev 02) > 00:0c.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06) > 00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN > interface > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge > 00:11.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev > 74) > > and the cat /proc/zaptel/* is: > > cat: /proc/zaptel/*: No such file or directory > > there is no files in /proc/zaptel/lsmod | grep zaptel Anything relevant in the kernel logs from the loading of the module wctdm ? -- Tzafrir Cohen icq#16849755 jabber:tzafrir at jabber.org +972-50-7952406 mailto:tzafrir.cohen at xorcom.com http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir
how can i see that??? thanks 2007/6/18, Tzafrir Cohen <tzafrir.cohen at xorcom.com>:> > On Mon, Jun 18, 2007 at 02:02:53PM +0200, Josu Lazkano wrote: > > Hello, my OpneVox card is an A400P01. > > > > And the output of lspci is: > > > > 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] > Host > > Bridge > > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge > > 00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network > > controller [HFC-PCI] (rev 02) > > 00:0c.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06) > > 00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX > Modem/ISDN > > interface > > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge > > 00:11.1 IDE interface: VIA Technologies, Inc. > > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] > (rev > > 74) > > > > and the cat /proc/zaptel/* is: > > > > cat: /proc/zaptel/*: No such file or directory > > > > there is no files in /proc/zaptel/ > > lsmod | grep zaptel > > Anything relevant in the kernel logs from the loading of the module > wctdm ? > > -- > Tzafrir Cohen > icq#16849755 jabber:tzafrir at jabber.org > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >-------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070618/baef1d38/attachment.htm
I experienced the same problem. The only way I could get both ISDN and analog working was unloading kernel modules for zaptel and mISDN after boot and then load them in the order: zaptel first and then mISDN. Still need to find out how to configure load order in linux. grz, Hans Feringa> On Mon, Jun 18, 2007 at 12:50:23PM +0200, Josu Lazkano wrote: >> Hello everybody! >> >> I have some problems with my Astersk. I have an analogical OpenVox card >> and >> A Billion ISDN card (with mISDN). >> >> I load the modules with modprobe zaptel and modprobe wctdm. >> >> When I run ztcfg -vv I have this: >> >> Zaptel Configuration >> =====================>> >> >> Channel map: >> >> Channel 01: FXS Kewlstart (Default) (Slaves: 01) >> >> 1 channels configured. >> >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > This means your /etc/zaptel.conf is incorrect. Start by correcting it. > Or maybe the driver has not loaded correctly. > > Which OpenVox card is it? > > What is the output of: > > lspci > cat /proc/zaptel/* > >> zaptel.conf: >> >> loadzone=es >> defaultzone=es >> fxsks=1 > > -- > Tzafrir Cohen > icq#16849755 jabber:tzafrir at jabber.org > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >
linux at shelob.nl wrote:> I experienced the same problem. The only way I could get both > ISDN and analog working was unloading kernel modules for zaptel > and mISDN after boot and then load them in the order: > zaptel first and then mISDN. Still need to find out how to configure > load order in linux. > > grz, > > Hans Feringa > > > > >> On Mon, Jun 18, 2007 at 12:50:23PM +0200, Josu Lazkano wrote: >> >>> Hello everybody! >>> >>> I have some problems with my Astersk. I have an analogical OpenVox card >>> and >>> A Billion ISDN card (with mISDN). >>> >>> I load the modules with modprobe zaptel and modprobe wctdm. >>> >>> When I run ztcfg -vv I have this: >>> >>> Zaptel Configuration >>> =====================>>> >>> >>> Channel map: >>> >>> Channel 01: FXS Kewlstart (Default) (Slaves: 01) >>> >>> 1 channels configured. >>> >>> ZT_CHANCONFIG failed on channel 1: No such device or address (6) >>> >> This means your /etc/zaptel.conf is incorrect. Start by correcting it. >> Or maybe the driver has not loaded correctly. >> >> Which OpenVox card is it? >> >> What is the output of: >> >> lspci >> cat /proc/zaptel/* >> >> >>> zaptel.conf: >>> >>> loadzone=es >>> defaultzone=es >>> fxsks=1 >>> >> -Hans, Have a look at the man page for modprobe.conf, specifically the install directive. There is an example of how to force the order. Bob...
On Mon, Jun 18, 2007 at 05:12:57PM +0300, Tzafrir Cohen wrote:> On Mon, Jun 18, 2007 at 02:02:53PM +0200, Josu Lazkano wrote: > > Hello, my OpneVox card is an A400P01. > > > > And the output of lspci is: > > > > 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host > > Bridge > > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge > > 00:0b.0 Network controller: Cologne Chip Designs GmbH ISDN network > > controller [HFC-PCI] (rev 02) > > 00:0c.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06) > > 00:0e.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN > > interface > > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge > > 00:11.1 IDE interface: VIA Technologies, Inc. > > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev > > 74) > > > > and the cat /proc/zaptel/* is: > > > > cat: /proc/zaptel/*: No such file or directory > > > > there is no files in /proc/zaptel/ > > lsmod | grep zaptel > > Anything relevant in the kernel logs from the loading of the module > wctdm ?One option: rmmod wctdm; modprobe wctdm; dmesg | tail Though browsing /var/log/kern.log (in Debian) and looking for wctdm may also be useful.> > -- > Tzafrir Cohen > icq#16849755 jabber:tzafrir at jabber.org > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users-- Tzafrir Cohen icq#16849755 jabber:tzafrir at jabber.org +972-50-7952406 mailto:tzafrir.cohen at xorcom.com http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir
Hello, I have solved. I must delete the netjetpci module from /etc/modprobe.d/blacklist: blacklist netjetpci thanks for all 2007/6/21, Tzafrir Cohen <tzafrir.cohen at xorcom.com>:> > On Thu, Jun 21, 2007 at 12:48:46PM +0200, Josu Lazkano wrote: > > Hello, I have the same problem as the begining. > > > > I reinstall all the system and i have the same error: > > > > asterisk:/usr/src/asterisk-1.2.19# ztcfg -vv > > > > Zaptel Configuration > > =====================> > > > > > Channel map: > > > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > > > > 1 channels configured. > > > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > > > The zaptel and wctdm modules are loaded correctly. > > cat /proc/zaptel/* > > > > > And the zapata and zaptel files are correctly too. > > cat /etc/zaptel.conf > > BTW: what is the output of: > > ./xpp/utils/genzaptelconf -l > > -- > Tzafrir Cohen > icq#16849755 jabber:tzafrir at jabber.org > +972-50-7952406 mailto:tzafrir.cohen at xorcom.com > http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >-------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070621/536b9a64/attachment.htm