On Thu, Sep 04, 2008 at 10:58:44PM -0400, sean darcy
wrote:> As best i could figure it out, I've installed dahdi and rc4.
>
> My TDM400P doesn't answer fxo or fxs.
>
> /etc/dahdi/system.conf:
> loadzone = us
> defaultzone=us
> fxoks=1,2
> fxsks=4
echocancel?
>
> /etc/asterisk/chan_dahdi.conf:
>
> [house-phones]
> context=internal ; Uses the [internal] context in extensions.conf
> signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
> dahdichan => 1 ; Telephone attached to port 1
> dahdichan => 2 ; Telephone attached to port 2
You confuse "dahdichan" with "channel"
Only the last dahdichan in a section is used. OTOH, it takes into
account ther things in that section.
Try:
[house-phones]
context=internal ; Uses the [internal] context in extensions.conf
signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
dahdichan => 1,2
Or, if you want to have some common settins and some different settings:
[house-phones](!)
context = internal ; Uses the [internal] context in extensions.conf
signalling = fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
group = 1
[phone1](house-phone)
dahdichan = 1
callerid = Name One <456>
[phone2](house-phone)
callerid = Someone Else <123>
group = 3
dahdichan = 2
dahdichan only works with 1.6.0 and above.
>
> [pstn]
> context=incoming-pstn-line ; Incoming calls go to [incoming-pstn-line]
> in extensions.conf
> signalling=fxs_ks ; fxs_ks Use FXS signalling for an FXO channel
> faxdetect=incoming
> busydetect=yes
> dahdichan => 4 ; PSTN attached to port 4
>
> dmesg:
>
> dahdi: Telephony Interface Registered on major 196
> dahdi: Version: 2.0.0-rc3
> ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
> ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [APC1] -> GSI 16 (level,
> low) -> IRQ 16
> PCI: Setting latency timer of device 0000:01:05.0 to 64
> Freshmaker version: 73
> Freshmaker passed register test
> Clocksource tsc unstable (delta = -71426924 ns)
> Module 0: Installed -- AUTO FXS/DPO
> Module 1: Installed -- AUTO FXS/DPO
> Module 2: Not installed
> Module 3: Installed -- AUTO FXO (FCC mode)
> Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules)
> INFO-xpp: revision trunk-r6056 MAX_XPDS=64 (8*8)
> INFO-xpp: FEATURE: without BRISTUFF support
> INFO-xpp: FEATURE: with PROTOCOL_DEBUG
> INFO-xpp: FEATURE: with sync_tick() from DAHDI
> INFO-xpp_usb: revision trunk-r6056
> usbcore: registered new interface driver xpp_usb
> dahdi: Registered tone zone 0 (United States / North America)
>
> dahdi_scan
> [1]
> active=yes
> alarms=OK
> description=Wildcard TDM400P REV I Board 5
> name=WCTDM/4
> manufacturer=Digium
> devicetype=Wildcard TDM400P REV I
> location=PCI Bus 01 Slot 06
> basechan=1
> totchans=4
> irq=16
> type=analog
> port=1,FXS
> port=2,FXS
> port=3,none
> port=4,FXO
What is the output of:
cat /proc/dahdi/*
>
> CLI> dahdi show status
> Description Alarms IRQ bpviol CRC4
> Fra Codi Options LBO
> Wildcard TDM400P REV I Board 5 OK 0 0 0
> CAS Unk YEL 0 db (CSU)/0-133 feet (DSX-1)
>
> But if I dial in, no dial tone, nothing on the cli.
> And:
>
> *CLI> dahdi show channels
> Chan Extension Context Language MOH Interpret
> Blocked State
> pseudo default default
> In Service
>
> Tried dahdi_genconf. No help.
>
> Reverted now.
>
> Any help appreciated.
>
> seam
>
>
> _______________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> AstriCon 2008 - September 22 - 25 Phoenix, Arizona
> Register Now: http://www.astricon.net
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
--
Tzafrir Cohen
icq#16849755 jabber:tzafrir.cohen at xorcom.com
+972-50-7952406 mailto:tzafrir.cohen at xorcom.com
http://www.xorcom.com iax:guest at local.xorcom.com/tzafrir