similar to: rxfax/txfax

I've been using spandsp and rxfax to receive faxes for a while now and over the past few days I've looked into the other side of things - txfax. I can't seem to get it working properly. I've included debug logs below of both the tx and rx side of things. I've tried three different servers, asterisk v1.0.6, 1.0.9 and CVS, FC2 and FC4, libtiff 3.5.7 and 3.7.1, TE405P and

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, I have still had no luck with faxing and am getting a couple of pages of the following debug message Changed from phase 1 to 4 DIS: Prefer 256 octet blocks Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm 2D coding Scan line length: 215mm Recording length: Unlimited Receiver's minimum scan line time: 0ms at 3.85

Hello, I tryed out spandsp with libtiff-3.5.7 and with Asterisk from CVS. I tryed to receive a fax on a CAPI channel. Finally I got a file with 8 byte length (/tmp/testfax.tif). How can I do next? Thanks in advance, Thomas ps: what are hardware requirements for sending/receiving faxes? -- creating pipe for PLCI=0x101 msn = 2258589 > sent ALERT_REQ PLCI = 0x101 --

I've seen people mention that they have fax reception working with Asterisk, spandsp, and app_rxfax. I'm using the latest Asterisk from CVS, SpanDSP 0.0.1k, and the latest app_rxfax.c (as mirrored by friendly list members recently), and libtiff 3.5.7. Asterisk is detecting the fax signal properly, and executing the fax extension in the dialplan. The fax part of the dialplan is pretty

Hi, I am trying to receive a fax with the spandsp library. The sending fax says "success" but there is no tiff file generated. I use "exten => 7000,1,rxfax(/tmp/testfax.tif)" in my extensions.conf. The connection is via SIP/G.711 as I have read on the list that this can sometimes work (I know Fax over IP is troublesome without T.38). I think the transmission should not

I am also having problems receiving my first fax. I get a 320byte file (for a 4 page fax). If I look a the tiff generated, is just has some few dots. I am sending the fax from a notebook with Windows XP to an X100P and using libtiff v3.5.7. Has anyone successfully received faxes ? Output to the console as follows: Changed from phase 0 to 1 > Start receiving document > Changed from

Can someone explain me what's going on and why the receiver of this fax guives up saying communication error? Slow carrier up Slow carrier down Slow carrier up <<< CSI: 40 20 20 20 20 20 20 20 34 39 34 35 36 34 39 35 30 20 39 33 2b CSI without final frame tag Remote fax gave CSI as: "+39 059465494 " <<< DIS: 80 00 ee f8 c4 00 DIS with final frame tag In

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log : Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow

Hi, I just sent this to Steve Underwood, but then found a bunch of posts on the mailing list about similar issues.. does anyone have the fix? I'm running asterisk CVS-HEAD-06/28/04-18:13:13, spandsp 0.0.1k, libtif 3.5.7 one thing i just noticed is that calls come in with format '72' which is G711A-law or LinearPCM.. it uses PCM for the call, i assume this is ok the results of RxFAX

Hi, I am trying to recice a fax with * using SpanDSP - but it doesn't create the output file. (See the bottom of log file). * Loads both app_rxfax.so and app_txfax.so fine. Also I can't make * autodetect an incomming fax call (yes I have enabled faxdetect=both in zapata.conf - though it's not a Zap device) Any ideas are welcome :-) Best Regards Michael L?jtnant System Details:

Hi, I have tried to install and configure the FAX app using the steps described in several mails on this list. When a FAX call arrives on X100P, the fax extension is executed, which looks like: exten => fax,1,RxFax(/var/spool/asterisk/incoming/${CALLERIDNUM}.tif) exten => fax,2,Hangup It tries to negociate, but nothing is received at the end and the other part times out. More, after this

I'm trying to send a fax to my asterisk box, however shortly after connecting the fax machine reports a "communication error" and hangs up. Below is the error I get from RxFax: Fast carrier training failed Nothing is written to the file system as far as the tiff is concerned. Any ideas on how to fix this? Thanks ---- Sending Fax Machine: HP PSC 2000 Series 2210

Hi, spandsp-0.0.2pre18 works fine for txfax with HT488(version-1.0.1.2), but rxfax doesn't work. After some FAX sounds, it hangup! Could someone tell me how to debug? The following is the * CLI> log to 192.168.0.161:43222 -- Executing NoOp("SIP/4881-bde9", "") in new stack -- Executing RxFAX("SIP/4881-bde9",

Dear Steve i have try SpanDSP from the first version to the last one (1k) with my Canon FAX and with my modem but every time i see a lot of message like this: ----- I send a Fax from my Canon B150 i have the following error: -- Starting simple switch on 'Zap/33-1' -- Executing RxFAX("Zap/33-1", "/home/user/testfax.tif") in new stack Changed from phase 0 to 1

Hi, Below if the error message which I got from asterisk. I was trying to fax to asterisk from my fax machine. I really dunno what is the problem. I use alaw & ulaw codec only through my ATA 186. Can anyone help me what could be the problem. -- Executing Goto("SIP/-080ef9a0", "13732|s|1") in new stack -- Goto (13732,s,1) -- Executing

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier

I'm trying to install the RxFax in Asterisk. After much trouble getting app_rxfax.c (and friends) compiles and installed into Asterisk (thanks to the many asterisk-users messages) it did get it installed. I have been unable to receive a legible fax. app_rxfax provides lots of debugging information but none useful to me. I was hoping that someone has an idea what might be going on.

I use http://www.voip-info.org/wiki-Asterisk+callingcard You only should compile the prepaid.c (look at readme file). Regards. Julio ----- Original Message ----- From: <clive18@webmail.co.za> To: <juliom@telelinkusa.net> Sent: Tuesday, April 20, 2004 12:47 AM Subject: fwd:Re: [Asterisk-Users] Asterisk prepaid debug > Hi > > Which pre-paid app are you using?. > Is it