similar to: fax output from Asterisk into file

Hi, I am trying to recice a fax with * using SpanDSP - but it doesn't create the output file. (See the bottom of log file). * Loads both app_rxfax.so and app_txfax.so fine. Also I can't make * autodetect an incomming fax call (yes I have enabled faxdetect=both in zapata.conf - though it's not a Zap device) Any ideas are welcome :-) Best Regards Michael L?jtnant System Details:

Hi, I have tried to install and configure the FAX app using the steps described in several mails on this list. When a FAX call arrives on X100P, the fax extension is executed, which looks like: exten => fax,1,RxFax(/var/spool/asterisk/incoming/${CALLERIDNUM}.tif) exten => fax,2,Hangup It tries to negociate, but nothing is received at the end and the other part times out. More, after this

Hello, I tryed out spandsp with libtiff-3.5.7 and with Asterisk from CVS. I tryed to receive a fax on a CAPI channel. Finally I got a file with 8 byte length (/tmp/testfax.tif). How can I do next? Thanks in advance, Thomas ps: what are hardware requirements for sending/receiving faxes? -- creating pipe for PLCI=0x101 msn = 2258589 > sent ALERT_REQ PLCI = 0x101 --

I use http://www.voip-info.org/wiki-Asterisk+callingcard You only should compile the prepaid.c (look at readme file). Regards. Julio ----- Original Message ----- From: <clive18@webmail.co.za> To: <juliom@telelinkusa.net> Sent: Tuesday, April 20, 2004 12:47 AM Subject: fwd:Re: [Asterisk-Users] Asterisk prepaid debug > Hi > > Which pre-paid app are you using?. > Is it

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier

I've been using spandsp and rxfax to receive faxes for a while now and over the past few days I've looked into the other side of things - txfax. I can't seem to get it working properly. I've included debug logs below of both the tx and rx side of things. I've tried three different servers, asterisk v1.0.6, 1.0.9 and CVS, FC2 and FC4, libtiff 3.5.7 and 3.7.1, TE405P and

Hi, I am trying to receive a fax with the spandsp library. The sending fax says "success" but there is no tiff file generated. I use "exten => 7000,1,rxfax(/tmp/testfax.tif)" in my extensions.conf. The connection is via SIP/G.711 as I have read on the list that this can sometimes work (I know Fax over IP is troublesome without T.38). I think the transmission should not

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log : Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

I've seen people mention that they have fax reception working with Asterisk, spandsp, and app_rxfax. I'm using the latest Asterisk from CVS, SpanDSP 0.0.1k, and the latest app_rxfax.c (as mirrored by friendly list members recently), and libtiff 3.5.7. Asterisk is detecting the fax signal properly, and executing the fax extension in the dialplan. The fax part of the dialplan is pretty

Hi, I'm trying to send a fax from a Zap channel to another Zap channel and I can't - below the logs. How could I solve this? Thanks! In RECEIVER: -- Accepting call from '' to '1980' on channel 0/2, span 1 Urgent handler -- Executing Answer("Zap/2-1", "") in new stack Urgent handler Urgent handler -- Executing Goto("Zap/2-1",

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

I am having a problem with SpanDSP. What happens is when I send a fax to SpanDSP the fax message seems to fail in the training phase. I think it's a timing error, however I have no idea about how to rectify the problem. I have included a copy of the log below. I am using a Digium TDM-400P card with 2 x FXO ports and 2 x FXS ports. The fax is connected to one of the FXS ports (Zap3). The

I'm trying to send a fax to my asterisk box, however shortly after connecting the fax machine reports a "communication error" and hangs up. Below is the error I get from RxFax: Fast carrier training failed Nothing is written to the file system as far as the tiff is concerned. Any ideas on how to fix this? Thanks ---- Sending Fax Machine: HP PSC 2000 Series 2210

Dear Steve i have try SpanDSP from the first version to the last one (1k) with my Canon FAX and with my modem but every time i see a lot of message like this: ----- I send a Fax from my Canon B150 i have the following error: -- Starting simple switch on 'Zap/33-1' -- Executing RxFAX("Zap/33-1", "/home/user/testfax.tif") in new stack Changed from phase 0 to 1

Dear Steve after a lot of compile from spanDSP first version to K and after i have compile * HEAD and Stable i cant understand where im wrong... - Mandrake 9.2 - libtiff3-3.5.7-11mdk I have add Header from your FTP but the result is this error.. Can you give me your opinion? Thanks in advance Dimitri -------- -- Executing RxFAX("Zap/35-1", "/home/user/testfax.tif") in

I am having a problem with SpanDSP. What happens is when I send a fax to SpanDSP the fax message seems to fail in the training phase. I think it's a timing error, however I have no idea about how to rectify the problem. I have included a copy of the log below. I am using a Digium TDM-400P card with 2 x FXO ports and 2 x FXS ports. The fax is connected to one of the FXS ports (Zap3). The

Here's one last plea for help from the list before I give up on the totally cool software FAX modem concept in complete despair (for now, at least, until I have more time to dig into it).... I am simply not able to successfully receive a FAX no matter what device I transmit from or how I bring the call into Asterisk. My lastest effort was a call from a Pitney-Bowes FAX machine into an X100P

Hi, I have still had no luck with faxing and am getting a couple of pages of the following debug message Changed from phase 1 to 4 DIS: Prefer 256 octet blocks Can receive fax Supported data signalling rates: V.27ter and V.29 R8x7.7lines/mm and/or 200x200pels/25.4mm 2D coding Scan line length: 215mm Recording length: Unlimited Receiver's minimum scan line time: 0ms at 3.85