similar to: rxfax problem

Hi, I have tried to install and configure the FAX app using the steps described in several mails on this list. When a FAX call arrives on X100P, the fax extension is executed, which looks like: exten => fax,1,RxFax(/var/spool/asterisk/incoming/${CALLERIDNUM}.tif) exten => fax,2,Hangup It tries to negociate, but nothing is received at the end and the other part times out. More, after this

Hi, I am trying to receive a fax with the spandsp library. The sending fax says "success" but there is no tiff file generated. I use "exten => 7000,1,rxfax(/tmp/testfax.tif)" in my extensions.conf. The connection is via SIP/G.711 as I have read on the list that this can sometimes work (I know Fax over IP is troublesome without T.38). I think the transmission should not

Hi all, I have installed FAX app as described in several mails. When a fax call is received, I get the following in the * console: -- Starting simple switch on 'Zap/1-1' -- Executing Answer("Zap/1-1", "") in new stack -- Executing Ringing("Zap/1-1", "") in new stack -- Executing Wait("Zap/1-1", "2") in new stack

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Initial handshake sounds fine, but asterisks dies before receive of the fax. Here is the log : Changed from phase 0 to 1 Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow carrier down Slow carrier up Slow

I am also having problems receiving my first fax. I get a 320byte file (for a 4 page fax). If I look a the tiff generated, is just has some few dots. I am sending the fax from a notebook with Windows XP to an X100P and using libtiff v3.5.7. Has anyone successfully received faxes ? Output to the console as follows: Changed from phase 0 to 1 > Start receiving document > Changed from

I'm trying to send a fax to my asterisk box, however shortly after connecting the fax machine reports a "communication error" and hangs up. Below is the error I get from RxFax: Fast carrier training failed Nothing is written to the file system as far as the tiff is concerned. Any ideas on how to fix this? Thanks ---- Sending Fax Machine: HP PSC 2000 Series 2210

I'm getting the following when sending to a specific fax machine. Any ideas? File name is '/var/spool/asterisk/email2fax/7F2SOeYJiU.tif' Changed from phase 0 to 2 Slow carrier up Slow carrier down Slow carrier up <<< NSF: 20 00 00 11 80 00 8a 49 10 53 54 49 52 4c 49 4e 47 20 43 4f 56 49 4e 47 54 00 67 00 80 80 80 0c 01 02 NSF without final frame tag The remote is made by

Hi, Below if the error message which I got from asterisk. I was trying to fax to asterisk from my fax machine. I really dunno what is the problem. I use alaw & ulaw codec only through my ATA 186. Can anyone help me what could be the problem. -- Executing Goto("SIP/-080ef9a0", "13732|s|1") in new stack -- Goto (13732,s,1) -- Executing

Here's one last plea for help from the list before I give up on the totally cool software FAX modem concept in complete despair (for now, at least, until I have more time to dig into it).... I am simply not able to successfully receive a FAX no matter what device I transmit from or how I bring the call into Asterisk. My lastest effort was a call from a Pitney-Bowes FAX machine into an X100P

Hi, I just sent this to Steve Underwood, but then found a bunch of posts on the mailing list about similar issues.. does anyone have the fix? I'm running asterisk CVS-HEAD-06/28/04-18:13:13, spandsp 0.0.1k, libtif 3.5.7 one thing i just noticed is that calls come in with format '72' which is G711A-law or LinearPCM.. it uses PCM for the call, i assume this is ok the results of RxFAX

I'm running asterisk CVS HEAD from 20040601 with spandsp 0.0.1k and libtiff 3.6.0 (no other copies are installed). I've put the audio files up at http://www.mixdown.ca/~andrew/dump/akohlsmith-faxsegfault.tgz -- the machine I am faxing from is a Canon IR3300 printer/copier/fax, but I get similar crashes from $29.95 fax machines too. :-) I'm trying to get a decent backtrace but

Hi, spandsp-0.0.2pre18 works fine for txfax with HT488(version-1.0.1.2), but rxfax doesn't work. After some FAX sounds, it hangup! Could someone tell me how to debug? The following is the * CLI> log to 192.168.0.161:43222 -- Executing NoOp("SIP/4881-bde9", "") in new stack -- Executing RxFAX("SIP/4881-bde9",

Hi all, After a long time having no time, I have finally done some fresh work on my software fax machine. I have replaced the original carrier tracking with something more robust. I have also added 4800, and 2400 bits per second modes, and cleaned up a few bugs in areas like superfine mode operation. I apologise for this update taking so long. At ftp://ftp.opencall.org/pub/spandsp you will

Hi, I am trying to recice a fax with * using SpanDSP - but it doesn't create the output file. (See the bottom of log file). * Loads both app_rxfax.so and app_txfax.so fine. Also I can't make * autodetect an incomming fax call (yes I have enabled faxdetect=both in zapata.conf - though it's not a Zap device) Any ideas are welcome :-) Best Regards Michael L?jtnant System Details:

Rxfax answers, makes handshake, and crashes once the page starts to send. It receives a .tif file of 8 bytes. Asterisk dumps core - gdb shows : #0 0x281fd86c in t4_rx_putbit () from /usr/local/lib/libspandsp.so.0 #1 0x281fea3c in fast_putbit () from /usr/local/lib/libspandsp.so.0 #2 0x28208324 in decode_baud () from /usr/local/lib/libspandsp.so.0 #3 0x2820893f in process_baud () from

Hi, Several people have reported problems sending faxes from spandsp-0.0.1k to Canon FAX machines. A spandsp user had the same problem with another make of FAX machine, and traced the problem to a bug in the file t30.c of spandsp. Line 542 says s->t4.rx_file[0] where it should say s->t4.tx_file[0]. This fixes his problem, and I suspect it will also fix the Canon fax machine problem.

Sorry to bore you more with the clock issue, but have you check /proc/zaptel/<span> to make sure it's not missing interrupts? There's also an option to record the audio for the fax, you could listen to that vs a recorded file that will receive correctly on a fax machine and see whether there is an obvious difference? (Good luck, that'll be really scraping the barrel!!) Does it

I use http://www.voip-info.org/wiki-Asterisk+callingcard You only should compile the prepaid.c (look at readme file). Regards. Julio ----- Original Message ----- From: <clive18@webmail.co.za> To: <juliom@telelinkusa.net> Sent: Tuesday, April 20, 2004 12:47 AM Subject: fwd:Re: [Asterisk-Users] Asterisk prepaid debug > Hi > > Which pre-paid app are you using?. > Is it

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier