similar to: PRI "wanrouter status" shows disconnected - system problem or Telco?

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference:

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Hello All Any body used sangoma card A101. I have problem with this card. My system are: Linux Redhat 8.0. asterisk 1.07 and libpri, zaptel,... i connected E1 and MF/R2 signalling. i configure HDLC and TDM Voice. this is my configure as belows: #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Sun May

Hi Everyone, We are using two Sangoma U100 (USB FXO) units connected to an Acer Aspire Revo (little PC running on Atom). The units work beautifully except for Monday :-) It maybe a conincedence or maybe the fact that Saturday/Sunday is off and something happens where one of these U100 modules goes into sleep and that's when all the 4 Dahdi channels are lost. So, I have been getting Monday

Hi, I''m using a linux 2.4.29 kernel and having trouble getting my filters added. The script I''m editing I actually use on a different system currently. Is this a tc/iproute/kernel type incompatibility? Any ideas how to debug it? Thanks, Jeremy # create a qdisc on T1 interface tc qdisc add dev w1g1 root handle 1: htb default 77 OK # create a master class tc class add dev w1g1

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all went okay. using sangoma a104dx on both machine. I followed the write up on http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 =

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hi, after many issues we finally managed to make our system do outgoing calls with perfect quality. However I cannot detect *any* form of incoming call. when I use an outside phone to call the E1 connected to the sangoma a102, I instantly get a fast busy tone. My /etc/zaptel.conf is: loadzone=us defaultzone=us #Sangoma A102 port 1 [slot:1 bus:4 span: 1] span=1,0,0,ccs,hdb3 bchan=1-15,17-31

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned