OK, I solved the problem(s)
It was a completely wrong setup from the provider.
Now anything is OK
zttool shows "OK" in the alarms
asterisk works great, parameters in zaptel.conf are
span=1,0,0,ccs,hdb3,yellow
bchan=1-15 # set this to 1-15,17-31 for E1
dchan=16 # set this to 16 for E1
bchan=17-31 # set this to 1-15,17-31 for E1
the only little problem is a delay of about 1 second or less in voice
Andrea
asterisk@frameweb
.it
Sent by: To
asterisk-users-bo asterisk-users@lists.digium.com
unces@lists.digiu cc
m.com
Subject
[Asterisk-Users] problems with PRI
19/09/2005 16.05
Please respond to
Asterisk Users
Mailing List -
Non-Commercial
Discussion
<asterisk-users@l
ists.digium.com>
Hi, I configured an asterisk box with 1
Digium Wildcard TE110P T1/E1 Card 0
I setup the jumper in e1 position.
my zaptel.conf :
defaultzone=it
loadzone=it
#gestione PRI
span=1,0,0,ccs,hdb3,crc4,yellow
bchan=1-15 # set this to 1-15,17-31 for E1
dchan=16 # set this to 16 for E1
bchan=17-31 # set this to 1-15,17-31 for E1
#
Asterisk starts correctly, I see th 30 channels.
Anyway I cannot put any call on the PSTN PRI Channel.
Actually I don't know
1) ccs or cas ? my provider (Fastweb Italy) does not answer.....
2) ami or hdb3 ? same answer (no answer)
3) crc or not ? my provider says it does not matter
moreover : what is supposed to show the zttool utility ?
If I push "Loop" nothing happens.
If I run ztcfg -v i see
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
Channel map:
Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Individual Clear channel (Default) (Slaves: 17)
Channel 18: Individual Clear channel (Default) (Slaves: 18)
Channel 19: Individual Clear channel (Default) (Slaves: 19)
Channel 20: Individual Clear channel (Default) (Slaves: 20)
Channel 21: Individual Clear channel (Default) (Slaves: 21)
Channel 22: Individual Clear channel (Default) (Slaves: 22)
Channel 23: Individual Clear channel (Default) (Slaves: 23)
Channel 24: Individual Clear channel (Default) (Slaves: 24)
Channel 25: Individual Clear channel (Default) (Slaves: 25)
Channel 26: Individual Clear channel (Default) (Slaves: 26)
Channel 27: Individual Clear channel (Default) (Slaves: 27)
Channel 28: Individual Clear channel (Default) (Slaves: 28)
Channel 29: Individual Clear channel (Default) (Slaves: 29)
Channel 30: Individual Clear channel (Default) (Slaves: 30)
Channel 31: Individual Clear channel (Default) (Slaves: 31)
with asterisk turned off, zttool shows
RED/NOP Digium Wildcard TE110P T1/E1 Card 0
with asterisk turned on, zttool shows
RED Digium Wildcard TE110P T1/E1 Card 0
if i try
cat /dev/zap/1
with asterisk turned off, I see a lot of raw data incoming
with asterisk turned on, I see
cat: /dev/zap/1: Device or resource busy
same with all the othe channel , except control channel 16
If I try cat: /dev/zap/1 with asterisk turned off, i see.
cat: /dev/zap/1cat: No such file or directory
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS/CRC4 RED
NOTOPEN
1 WCT1/0/1 Clear
2 WCT1/0/2 Clear
3 WCT1/0/3 Clear
4 WCT1/0/4 Clear
5 WCT1/0/5 Clear
6 WCT1/0/6 Clear
7 WCT1/0/7 Clear
8 WCT1/0/8 Clear
9 WCT1/0/9 Clear
10 WCT1/0/10 Clear
11 WCT1/0/11 Clear
12 WCT1/0/12 Clear
13 WCT1/0/13 Clear
14 WCT1/0/14 Clear
15 WCT1/0/15 Clear
16 WCT1/0/16 HDLCFCS
17 WCT1/0/17 Clear
18 WCT1/0/18 Clear
19 WCT1/0/19 Clear
20 WCT1/0/20 Clear
21 WCT1/0/21 Clear
22 WCT1/0/22 Clear
23 WCT1/0/23 Clear
24 WCT1/0/24 Clear
25 WCT1/0/25 Clear
26 WCT1/0/26 Clear
27 WCT1/0/27 Clear
28 WCT1/0/28 Clear
29 WCT1/0/29 Clear
30 WCT1/0/30 Clear
31 WCT1/0/31 Clear
If I try cat: /dev/zap/1 with asterisk turned ON, i see.
cat: /dev/zap/1cat: No such file or directory
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS/CRC4 RED
1 WCT1/0/1 Clear (In use)
2 WCT1/0/2 Clear (In use)
3 WCT1/0/3 Clear (In use)
4 WCT1/0/4 Clear (In use)
5 WCT1/0/5 Clear (In use)
6 WCT1/0/6 Clear (In use)
7 WCT1/0/7 Clear (In use)
8 WCT1/0/8 Clear (In use)
9 WCT1/0/9 Clear (In use)
10 WCT1/0/10 Clear (In use)
11 WCT1/0/11 Clear (In use)
12 WCT1/0/12 Clear (In use)
13 WCT1/0/13 Clear (In use)
14 WCT1/0/14 Clear (In use)
15 WCT1/0/15 Clear (In use)
16 WCT1/0/16 HDLCFCS (In use)
17 WCT1/0/17 Clear (In use)
18 WCT1/0/18 Clear (In use)
19 WCT1/0/19 Clear (In use)
20 WCT1/0/20 Clear (In use)
21 WCT1/0/21 Clear (In use)
22 WCT1/0/22 Clear (In use)
23 WCT1/0/23 Clear (In use)
24 WCT1/0/24 Clear (In use)
25 WCT1/0/25 Clear (In use)
26 WCT1/0/26 Clear (In use)
27 WCT1/0/27 Clear (In use)
28 WCT1/0/28 Clear (In use)
29 WCT1/0/29 Clear (In use)
30 WCT1/0/30 Clear (In use)
31 WCT1/0/31 Clear (In use)
4 RED
Any help will be greatly appreciated,
thanks in advance,
Andrea
Chi ricevesse questa mail per errore e' gentilmente pregato di cancellarla.
Visitate il sito http://www.frameweb.it
_______________________________________________
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users
Chi ricevesse questa mail per errore e' gentilmente pregato di cancellarla.
Visitate il sito http://www.frameweb.it