I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is
a TDM400P and a TE410P installed after upgrade.
The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position.
I see boot, WCT4xxP loading first and WCFXS loading second.
According to my understanding, given above, the TE410P should be configured
first, then the TDM400P. However, I'm not sure how to show channels numbers
for the FXS Ports.
This was working properly before I upgraded to TDM400P (was X100P). But
now the TE410P LED's are flashing RED
Please Help
Bart
Here is my current Zaptel.conf:
# Span 1: TE4/0/1 "TE410P (PCI) Card 0 Span 1" AMI/D4
span=1,0,0,d4,ami
e&m=1-24
# Span 2: TE4/0/2 "TE410P (PCI) Card 0 Span 2" AMI/D4 RED
span=2,0,0,d4,ami
e&m=25-48
# Span 3: TE4/0/3 "TE410P (PCI) Card 0 Span 3" AMI/D4 RED
span=3,0,0,d4,ami
e&m=49-72
# Span 4 TE4/0/4 "TE410P (PCI) Card 0 Span 4" AMI/D4 RED
span=4,0,0,d4,ami
e&m=73-96
# Span 5: WCTDM/0 "Wildcard TDM400P REV E/F Board 1"
fxoks=97
fxoks=98
# channel 3, WCTDM, inactive.
# channel 4, WCTDM, FXO
fxsks=99
And Current Zapata.conf:
; Span 1: TE4/0/1 "TE410P (PCI) Card 0 Span 1"
; This T1 is attached to in-house CUST 3 System
;
language=en
rxwink=300
usecallerid=yes
hidecallerid=no
callwaiting=no
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
immediate=no
busydetect=no
busycount=15
callprogress=no
;relaxdtmf=yes
;callerid=asreceived
faxdetect=incoming
signalling =>em_w
group = 2
channel => 1-24
; Span 2: TE4/0/2 "TE410P (PCI) Card 0 Span 2"
; This T1 is attached to inhouse CUST 10 System
;
language=en
rxwink=300
usecallerid=yes
hidecallerid=no
callwaiting=no
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
immediate=no
busydetect=no
busycount=15
callprogress=no
;relaxdtmf=yes
;callerid=asreceived
faxdetect=incoming
signalling =>em_w
group = 3
channel => 25-48
; Span 3: TE4/0/3 "TE410P (PCI) Card 0 Span 3"
; This T1 is attached to WorldCom Local 714 DID's
language=en
context=from-localt1 ; <rxwink=300
usecallerid=yes
hidecallerid=no
callwaiting=no
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
immediate=no
busydetect=no
busycount=15
callprogress=no
;relaxdtmf=yes
;callerid=asreceived
faxdetect=incoming
signalling =>em_w
group = 4
channel => 49-72
; Span 4 TE4/0/4 "TE410P (PCI) Card 0 Span 4"
; GBX inbound & outbound T1
language=en
context=from-tollfree ; <rxwink=300
usecallerid=yes
hidecallerid=no
callwaiting=no
usecallingpres=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
immediate=no
busydetect=no
busycount=15
callprogress=no
;relaxdtmf=yes
;callerid=asreceived
faxdetect=incoming
signalling =>em_w
group = 5
channel => 73-96
; Span 5: WCTDM/0 "Wildcard TDM400P REV E/F Board 1"
;
; Note: this is an extension. Create a ZAP extension in AMP
; for Channel 1
;
signalling=fxo_ks
context=from-internal
group=1
channel => 97
;
; Note: this is an extension. Create a ZAP extension in AMP
; for Channel 2
;
signalling=fxo_ks
context=from-internal
group=1
channel => 98
;
; channel 3, WCTDM, inactive.
;
; Note: this is a trunk. Create a ZAP trunk in AMP
; for Channel 4
;
signalling=fxs_ks
context=from-pstn
group=0
channel => 99
