Mark F. Vickers
2004-Nov-29 20:31 UTC
[Asterisk-Users] TE410P lights don't blink read after the module is loaded
Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards be firmware upgraded? I got the modules from CVS, are they packaged with version version 1.0.2 some place or is getting the modules from CVS the correct thing to do? Config files are below. Thanks Mark Vickers RealNetworks, Inc. ____________________________________________________________ root@asterisk:~# /sbin/modprobe zaptel root@asterisk:~# /sbin/modprobe wct4xxp From dmesg: Zapata Telephony Interface Registered on major 196 Found TE410P at base address fc200000, remapped to e088f000 TE410P version c01a003a, burst ON FALC version: 00000005, Board ID: 00 Reg 0: 0x1b96b800 Reg 1: 0x1b96b000 Reg 2: 0x07fc07fc Reg 3: 0x00000000 Reg 4: 0x00000000 Reg 5: 0x00000000 Reg 6: 0xc01a003a Reg 7: 0x00001000 Reg 8: 0x00000000 Reg 9: 0x00ff0000 Reg 10: 0x00000000 TE410P: Launching card: 0 TE410P: Setting up global serial parameters Found a Wildcard: Wildcard TE410P-Xilinx From the FAQ. Q. When will the LED lights come on, on my T100P/E100P/T400p/E400P/TE4XXP? What about the TE410P? What about the TDM400P? A. For the T100P/E100P/T400p/E400P/TE4XXP cards there will be no lights on the cards until the module is loaded. When you load the module the lights should flash red. When a channel bank or circuit are connected to the card, they should turn green with the module loaded. For the TE410P the LED's should scroll(knightrider) even without the module being loaded or anything plugged in. When you load the module and have no circuit/channel bank the LED's should flash red. With the module loaded and a circuit/channel bank connected they should be solid green. For the TDM400P, when you load the module they LED's will come on green. If the module is not loaded they won't be on at all. They do not change if a phone is plugged in or not. root@asterisk:~# cat /etc/asterisk/zapata.conf |grep -v "^;" [channels] context=default switchtype=national signalling=em_w rxwink=2500 ; Atlas seems to use long (250ms) winks start=250 debounce=333 usecallerid=yes hidecallerid=yes callwaiting=no usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes #rxgain=-10.1 #txgain=-10.1 group=1 callgroup=1 pickupgroup=1 immediate=no musiconhold=default signalling=em_w channel => 1-24 root@asterisk:~# root@asterisk:~# cat /etc/zaptel.conf |grep -v "^#" span=1,2,0,esf,b8zs e&m=1-24 loadzone = us defaultzone=us root@asterisk:~# root@asterisk:~# lsmod Module Size Used by Not tainted wct4xxp 51680 0 (unused) zaptel 176640 0 [wct4xxp] ipt_state 568 4 (autoclean) ipt_REJECT 3480 1 (autoclean) iptable_mangle 2136 0 (autoclean) (unused) iptable_nat 23256 0 (autoclean) (unused) ip_conntrack 30376 2 (autoclean) [ipt_state iptable_nat] iptable_filter 1740 1 ip_tables 15360 7 [ipt_state ipt_REJECT iptable_mangle iptable_nat iptable_filter] e1000 67648 1 root@asterisk:~#
mvickers
2004-Nov-30 00:01 UTC
[Asterisk-Users] TE410P lights don't blink red after the module is loaded
subject should have read "red" not read Mark F. Vickers wrote:> Greetings, > > According to the FAQ "When you load the module and have no > circuit/channel bank the LED's should flash red" > > I get the "knight rider" lights before the module loads, but after the > modules are loaded I don't get any lights, other equipment plugged in or > not. > > The card has been on my shelf a while so I wonder if it needs a firmware > upgrade ? Can the cards be firmware upgraded? > > I got the modules from CVS, are they packaged with version version 1.0.2 > some place or is getting the modules from CVS the correct thing to do? > > Config files are below. > > Thanks > > Mark Vickers > RealNetworks, Inc. > > > ____________________________________________________________ > > root@asterisk:~# /sbin/modprobe zaptel > root@asterisk:~# /sbin/modprobe wct4xxp > > From dmesg: > > Zapata Telephony Interface Registered on major 196 > Found TE410P at base address fc200000, remapped to e088f000 > TE410P version c01a003a, burst ON > FALC version: 00000005, Board ID: 00 > Reg 0: 0x1b96b800 > Reg 1: 0x1b96b000 > Reg 2: 0x07fc07fc > Reg 3: 0x00000000 > Reg 4: 0x00000000 > Reg 5: 0x00000000 > Reg 6: 0xc01a003a > Reg 7: 0x00001000 > Reg 8: 0x00000000 > Reg 9: 0x00ff0000 > Reg 10: 0x00000000 > TE410P: Launching card: 0 > TE410P: Setting up global serial parameters > Found a Wildcard: Wildcard TE410P-Xilinx > > > > From the FAQ. > > Q. When will the LED lights come on, on my > T100P/E100P/T400p/E400P/TE4XXP? What about the TE410P? What about the > TDM400P? > A. For the T100P/E100P/T400p/E400P/TE4XXP cards there will be no > lights on the cards until the module is loaded. When you load the module > the lights should flash red. When a channel bank or circuit are > connected to the card, they should turn green with the module loaded. > For the TE410P the LED's should scroll(knightrider) even without the > module being loaded or anything plugged in. When you load the module and > have no circuit/channel bank the LED's should flash red. With the module > loaded and a circuit/channel bank connected they should be solid green. > For the TDM400P, when you load the module they LED's will come on green. > If the module is not loaded they won't be on at all. They do not change > if a phone is plugged in or not. > > > root@asterisk:~# cat /etc/asterisk/zapata.conf |grep -v "^;" > > [channels] > context=default > switchtype=national > signalling=em_w > rxwink=2500 ; Atlas seems to use long (250ms) winks > start=250 > debounce=333 > usecallerid=yes > hidecallerid=yes > callwaiting=no > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=yes > relaxdtmf=yes > #rxgain=-10.1 > #txgain=-10.1 > group=1 > callgroup=1 > pickupgroup=1 > > immediate=no > musiconhold=default > > signalling=em_w > > channel => 1-24 > > root@asterisk:~# > > > > root@asterisk:~# cat /etc/zaptel.conf |grep -v "^#" > span=1,2,0,esf,b8zs > e&m=1-24 > loadzone = us > defaultzone=us > root@asterisk:~# > > > root@asterisk:~# lsmod > Module Size Used by Not tainted > wct4xxp 51680 0 (unused) > zaptel 176640 0 [wct4xxp] > ipt_state 568 4 (autoclean) > ipt_REJECT 3480 1 (autoclean) > iptable_mangle 2136 0 (autoclean) (unused) > iptable_nat 23256 0 (autoclean) (unused) > ip_conntrack 30376 2 (autoclean) [ipt_state iptable_nat] > iptable_filter 1740 1 > ip_tables 15360 7 [ipt_state ipt_REJECT iptable_mangle > iptable_nat iptable_filter] > e1000 67648 1 > root@asterisk:~# > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users
Peter Svensson
2004-Nov-30 00:17 UTC
[Asterisk-Users] TE410P lights don't blink read after the module is loaded
On Mon, 29 Nov 2004, Mark F. Vickers wrote:> According to the FAQ "When you load the module and have no > circuit/channel bank the LED's should flash red" > > I get the "knight rider" lights before the module loads, but after the > modules are loaded I don't get any lights, other equipment plugged in or > not.Have you run ztcfg to load the zaptel.conf configuration into the driver? Peter
Hadi Jadallah
2004-Nov-30 00:37 UTC
[Asterisk-Users] TE410P lights don't blink read after the module is loaded
Good day to all, I had the same issue on multiple occasions and that scared me. I thought the card went busted. But the fastest solution I found was to change the PCI slot the card is inserted into. Also, went into bios and disabled all the those options related to allocating IRQs to some hardware on my machine that I don?t use. Some people suggested that the card might be sharing an IRQ with some other hardware on the server. Check cat /proc/interrupts and see if it is the case. Other than that, just try changing the PCI slot. Yours, Hadi. ------------------------------ Message: 10 Date: Mon, 29 Nov 2004 19:31:24 -0800 From: "Mark F. Vickers" <mvickers@real.com> Subject: [Asterisk-Users] TE410P lights don't blink read after the module is loaded To: asterisk-users@lists.digium.com Message-ID: <41ABE98C.6010902@real.com> Content-Type: text/plain; charset=ISO-8859-1; format=flowed Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards be firmware upgraded? I got the modules from CVS, are they packaged with version version 1.0.2 some place or is getting the modules from CVS the correct thing to do? Config files are below. Thanks Mark Vickers RealNetworks, Inc. ____________________________________________________________ root@asterisk:~# /sbin/modprobe zaptel root@asterisk:~# /sbin/modprobe wct4xxp From dmesg: Zapata Telephony Interface Registered on major 196 Found TE410P at base address fc200000, remapped to e088f000 TE410P version c01a003a, burst ON FALC version: 00000005, Board ID: 00 Reg 0: 0x1b96b800 Reg 1: 0x1b96b000 Reg 2: 0x07fc07fc Reg 3: 0x00000000 Reg 4: 0x00000000 Reg 5: 0x00000000 Reg 6: 0xc01a003a Reg 7: 0x00001000 Reg 8: 0x00000000 Reg 9: 0x00ff0000 Reg 10: 0x00000000 TE410P: Launching card: 0 TE410P: Setting up global serial parameters Found a Wildcard: Wildcard TE410P-Xilinx From the FAQ. Q. When will the LED lights come on, on my T100P/E100P/T400p/E400P/TE4XXP? What about the TE410P? What about the TDM400P? A. For the T100P/E100P/T400p/E400P/TE4XXP cards there will be no lights on the cards until the module is loaded. When you load the module the lights should flash red. When a channel bank or circuit are connected to the card, they should turn green with the module loaded. For the TE410P the LED's should scroll(knightrider) even without the module being loaded or anything plugged in. When you load the module and have no circuit/channel bank the LED's should flash red. With the module loaded and a circuit/channel bank connected they should be solid green. For the TDM400P, when you load the module they LED's will come on green. If the module is not loaded they won't be on at all. They do not change if a phone is plugged in or not. root@asterisk:~# cat /etc/asterisk/zapata.conf |grep -v "^;" [channels] context=default switchtype=national signalling=em_w rxwink=2500 ; Atlas seems to use long (250ms) winks start=250 debounce=333 usecallerid=yes hidecallerid=yes callwaiting=no usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes #rxgain=-10.1 #txgain=-10.1 group=1 callgroup=1 pickupgroup=1 immediate=no musiconhold=default signalling=em_w channel => 1-24 root@asterisk:~# root@asterisk:~# cat /etc/zaptel.conf |grep -v "^#" span=1,2,0,esf,b8zs e&m=1-24 loadzone = us defaultzone=us root@asterisk:~# root@asterisk:~# lsmod Module Size Used by Not tainted wct4xxp 51680 0 (unused) zaptel 176640 0 [wct4xxp] ipt_state 568 4 (autoclean) ipt_REJECT 3480 1 (autoclean) iptable_mangle 2136 0 (autoclean) (unused) iptable_nat 23256 0 (autoclean) (unused) ip_conntrack 30376 2 (autoclean) [ipt_state iptable_nat] iptable_filter 1740 1 ip_tables 15360 7 [ipt_state ipt_REJECT iptable_mangle iptable_nat iptable_filter] e1000 67648 1 root@asterisk:~#