I have followed these two for configuration of sangoma
A101
http://www.ss7box.com/s01_setup.html
http://www.ss7box.com/support_wancfg_1.html
on my side "wanrouter star/restart" is working fine
when i am tring to "ztcfg -vvv" i am getting
and when i am tring to load asterisk getting error "No
such device or address" since two days i am tring to
search on google but found nothin
------------------/etc/asterisk/zapata.conf
[channels]
context = default
switchtype = Euroisdn
usecallerid = yes
echocancel = yes
echocancelwhenbridged = yes
rxgain = 0.0
txgain = 0.0
signalling = pri_cpe
group =1
channel = 1-15,17-31
------------------/etc/zaptel.conf
loadzone = uk
defaultzone = uk
#span definitions
span = 1,1,0,ccs,hdb3,crc4,yellow
#channel definitions
bchan = 1-15,17-31
dchan = 16
------------------------------
# ls /proc/zaptel/
nothing
-------------------------------
# ls /dev/zap/
channel ctl pseudo timer
-------------------------------------
----------------asterisk orror on
Load------------------------
Jun 4 13:53:02 WARNING[12317]: chan_zap.c:923
zt_open: Unable to specify channel 1: No such device
or address
Jun 4 13:53:02 ERROR[12317]: chan_zap.c:6883 mkintf:
Unable to open channel 1: No such device or address
here = 0, tmp->channel = 1, channel = 1
Jun 4 13:53:02 ERROR[12317]: chan_zap.c:10319
setup_zap: Unable to register channel '1-15'
Jun 4 13:53:02 WARNING[12317]: loader.c:414
__load_resource: chan_zap.so: load_module failed,
returning -1
Jun 4 13:53:02 WARNING[12317]: loader.c:554
load_modules: Loading module chan_zap.so failed!
-----------------------------------------------
-----------------"ztcfg
-vvv"------------------------------
Zaptel Configuration
=====================
SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet
(DSX-1)
Channel map:
Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)
31 channels configured.
ZT_SPANCONFIG failed on span 1: No such device or
address (6)
------------wanrouter status--------------------------
# wanrouter status
Devices currently active:
wanpipe1
Wanpipe Config:
Device name | Protocol Map | Adapter | IRQ | Slot/IO
| If's | CLK | Baud rate |
wanpipe1 | N/A | A101/2 | 11 | 1
| 1 | EXT | 0 |
Wanrouter Status:
Device name | Protocol | Station | Status |
wanpipe1 | AFT HDLC | N/A | Disconnected |
>
> Im trying to install and configure sangoma ...
> every thing is OK but when type the command
> "wanrouter
> start" the following error apears:
> wan Driver not found.
>
> Thanks for any help
>
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com