similar to: Sangoma A101 configuration

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

I have an issue that hopefully you can help me solve. I've got the sangoma a101 card and installed it on freebsd but I according to the manual I should be see when running dmesg PCi0 vendor..... something that tells me sangoma it's being recognized by the system. Now this is the 2nd card I try, the first one according to support was faulty and they sent me a new one. Is it possible to be

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hello All, I have a setup of ABE on rPath linux,Sangoma A101D, and a T-1 line (Not PRI) which is all happily coexisting and all lights are green. The T-1 comes in from the world into a "Shark Box" which splits the T into 384K data and 6 channels voice. The data side is working great. The voice side, not so great. It was originally broken out to 6 pots line and Verizon came back

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

We are having an occasional one w-way audio problem that occurs about every 25 - 30 calls on a system configured as follows: Asterisk 1.2.12.1 Sangoma A101 w/wanpipe beta9 Polycom 500s w 1.5.3 This happens only on inbound calls from the PRI. The external caller can hear our customer answer and say hello, however, our customer cannot here their caller. Typically, the caller calls right back

Has anyone seen something like this before. Randomly, on longish calls, the local side of the call audio goes dead. Meaning remote caller can hear us but we cannot hear the remote person? Linux voip 2.6.18-128.1.6.el5 #1 SMP Wed Apr 1 09:10:25 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux Asterisk 1.4.24.1, Copyright (C) 1999 - 2008 Digium, Inc. and others. WANPIPE Release: 3.4.1 Wanpipe Config:

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference:

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hello, I have a Sangoma A101 connected to an ISDN30 (E1 in the UK) with some Snom 300 and Idefisk softphones. I can do SIP and IAX2 calls just fine, however I cant get any audio in either direction on the Zap channels. When I call in or dial out over the ISDN30 (UK E1) I can see the call answered/placed on the CLI and then silence follows. I've been provisioned 25 out of the 31 channels only

Hi ! We curently have a centos 5 / asterisk 1.4 server that we have some DTMF problems with. It has a Sangoma A104d card and only port one is used to connect to the PSTN. Port 2 is conencted via a cross-over cable to a RAS for modem access and port 3 is connected for data communication via PPP. Now, I want to freshen this setup to something newer. So I installed a Scientific Linux 6 server,

Hi, I have a client who has a system with a Sangoma 1 port PRI card with echo canceling in it. For some reason, when the system comes up the PRI will stay up for about 4-5 hours, then drop. "zap show status" shows everything as ok, but we can't make or receive any calls until the system is rebooted. Just restarting asterisk does not fix the problem. I am going to call

Hi everyone, I'm trying to get a Sangoma A101D-X card talking to a Sasktel PRI (Megalink) circuit and having some trouble getting it to handshake. Thanks for any help or suggestions to diagnose this problem. The problem is that Asterisk has trouble bringing up the link. I see the following lines every couple of minutes: == Primary D-Channel on span 1 up == Primary D-Channel on

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101