So I took a chance with an X100P knock-off on eBay. I'm running Asterisk +
FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel
2.6.16.16. Everything has been fine up until now.
I compile the 1.2.5 Zaptel drivers without a problem, get the udev
configuration in, modprobe zaptel, and finally modprobe wcfxo. At this
point, I get the message:
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
FATAL: Error running install command for wcfxo
dmesg gives me:
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.2.5 Echo Canceller: MG2
Failed to initailize DAA, giving up...
wcfxo: probe of 0000:00:0e.0 failed with error -5
syslog tells me:
May 25 21:28:20 asterisk kernel: Failed to initailize DAA, giving up...
May 25 21:28:20 asterisk kernel: wcfxo: probe of 0000:00:0e.0 failed with
error -5
ztcfg -vv says:
Channel 01: FXS Kewlstart (Default) (Slaves: 01)
1 channels configured.
ZT_CHANCONFIG failed on channel 1: No such device or address (6)
and lspci -vv tells me this:
00:0e.0 Communication controller: Motorola: Unknown device 5608
Subsystem: Motorola: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at fe000800 [size=256]
Region 1: Memory at 81803000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
One of the reasons I'm running on a PowerMac is specifically because
I've
been told the X100P cards work well on this type of hardware, since it tends
to not have problems with flawed PCI buses and IRQ sharing, but I'm starting
to have my doubts. If anyone has experience with X100P cards on PPC, or have
any other insights, it would be greatly appreciated.
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20060525/2b45f83c/attachment.htm
Lachek Butalek wrote:> So I took a chance with an X100P knock-off on eBay. I'm running > Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh > 10.2 and kernel 2.6.16.16 <http://2.6.16.16>. Everything has been fine > up until now. > I compile the 1.2.5 Zaptel drivers without a problem, get the udev > configuration in, modprobe zaptel, and finally modprobe wcfxo. At this > point, I get the message: > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > FATAL: Error running install command for wcfxo > > dmesg gives me: > > Zapata Telephony Interface Registered on major 196 > Zaptel Version: 1.2.5 Echo Canceller: MG2 > Failed to initailize DAA, giving up... > wcfxo: probe of 0000:00:0e.0 failed with error -5 > > syslog tells me: > > May 25 21:28:20 asterisk kernel: Failed to initailize DAA, giving up... > May 25 21:28:20 asterisk kernel: wcfxo: probe of 0000:00:0e.0 failed > with error -5 > > ztcfg -vv says: > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > 1 channels configured. > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > and lspci -vv tells me this: > > 00:0e.0 Communication controller: Motorola: Unknown device 5608 > Subsystem: Motorola: Unknown device 0000 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B-On an Intel machine, it reports a Tigerjet chip. Looks as if you may have the wrong modem chip? John Novack
>From what I understood Zaptel was ported to the Mac quite some time ago.http://lists.digium.com/pipermail/asterisk-users/2004-October/060872.html Also, TerraSoft sponsored an Asterisk port to YellowDog Linux on PPC - from what I gather, with full Zaptel support. http://www.voip-info.org/wiki/view/Asterisk+Linux+Yellow+Dog I didn't think it's be necessary to run YDL to get Zaptel to work. Does anyone know if this is the case? From what I understand, as long as zaptel compiles it's up to udev and the kernel to do the remaining hardware detection and resource assignment, which should be a distribution-agnostic process. Is it possible that this particular chip used in this particular X100P clone is not supported on LinuxPPC? It is a Motorola 6508 chip, identical to the SM56 winmodem. A picture of the card is here: http://cgi.ebay.ca/Its-Real-X100P-FXO-card-oem-for-Digium-Asterisk-pbx_W0QQitemZ9730539695QQcategoryZ61841QQssPageNameZWDVWQQrdZ1QQcmdZViewItem#ebayphotohosting Appreciative for any help. On 5/25/06, Lachek Butalek <lachek@gmail.com> wrote:> > So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + > FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel > 2.6.16.16. Everything has been fine up until now. > I compile the 1.2.5 Zaptel drivers without a problem, get the udev > configuration in, modprobe zaptel, and finally modprobe wcfxo. At this > point, I get the message: > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > FATAL: Error running install command for wcfxo > > dmesg gives me: > > Zapata Telephony Interface Registered on major 196 > Zaptel Version: 1.2.5 Echo Canceller: MG2 > Failed to initailize DAA, giving up... > wcfxo: probe of 0000:00:0e.0 failed with error -5 > > syslog tells me: > > May 25 21:28:20 asterisk kernel: Failed to initailize DAA, giving up... > May 25 21:28:20 asterisk kernel: wcfxo: probe of 0000:00:0e.0 failed with > error -5 > > ztcfg -vv says: > > Channel 01: FXS Kewlstart (Default) (Slaves: 01) > 1 channels configured. > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > > and lspci -vv tells me this: > > 00:0e.0 Communication controller: Motorola: Unknown device 5608 > Subsystem: Motorola: Unknown device 0000 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (250ns min, 32000ns max) > Interrupt: pin A routed to IRQ 24 > Region 0: I/O ports at fe000800 [size=256] > Region 1: Memory at 81803000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [40] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA > PME(D0+,D1-,D2+,D3hot+,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > One of the reasons I'm running on a PowerMac is specifically because I've > been told the X100P cards work well on this type of hardware, since it tends > to not have problems with flawed PCI buses and IRQ sharing, but I'm starting > to have my doubts. If anyone has experience with X100P cards on PPC, or have > any other insights, it would be greatly appreciated. >-------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060526/162c43a1/attachment.htm
> So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + > FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel > 2.6.16.16. Everything has been fine up until now. > I compile the 1.2.5 Zaptel drivers without a problem, get the udev > configuration in, modprobe zaptel, and finally modprobe wcfxo. At this > point, I get the message: > > ZT_CHANCONFIG failed on channel 1: No such device or address (6) > FATAL: Error running install command for wcfxo > > dmesg gives me: > > Zapata Telephony Interface Registered on major 196 > Zaptel Version: 1.2.5 Echo Canceller: MG2 > Failed to initailize DAA, giving up... > wcfxo: probe of 0000:00:0e.0 failed with error -5this is a problem if the card shares interrupt with something on MOtherBOard. configure the slot to other irq, or move the card to other irq. lspci -v will be your friend. Check if someone uses same IRQ as motorola card. -- WoodOO-[P]an[G]alaktikan[A]gent-People <][> http://shadow.pganet.com wpeople@shadow.pganet.com]iCQ#33118021[wpeople.on.iRCNet]wpeople@RedHat.users