thr3ads.net - asterisk users - [Asterisk-Users] Problem getting two x200p cards working on 1.2.4 [Mar 2006]

If this information is useful, please help other people find it:
Share via:

Guillermo Salas M

2006-Mar-06 14:25 UTC

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp
 kernel. 

I've two x100p cards connected, only one card is reconigzed by asterisk.

02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN interface
02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
compatible 10/100 Ethernet (rev 31)
02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN interface

This is the cli output for zap show channels :

My /etc/zaptel.conf :

# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#

# It must be in the module loading order


# Span 1: WCFXO/1 "Generic Clone Board 2"
fxsks=1

# Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"

# Global data

loadzone        = us
defaultzone     = us


My /etc/asterisk/zapata-auto.conf

; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is
intended
; to be #include-d by /etc/zapata.conf that will include the global
settings
;
callerid=asreceived

; Span 1: WCFXO/1 "Generic Clone Board 2"
signalling=fxs_ks
; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 1
context=from-pstn
group=0
channel => 1


; Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"


This is the corresponding 'lspci -vv -n' for my two cards:

02:01.0 Class 0780: e159:0001
        Subsystem: 8086:0003
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (250ns min, 32000ns max)
        Interrupt: pin A routed to IRQ 201
        Region 0: I/O ports at b800 [size=256]
        Region 1: Memory at feaff000 (32-bit, non-prefetchable)
[size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


02:03.0 Class 0780: e159:0001
        Subsystem: 8086:0003
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (250ns min, 32000ns max)
        Interrupt: pin A routed to IRQ 177
        Region 0: I/O ports at b000 [size=256]
        Region 1: Memory at feafd000 (32-bit, non-prefetchable)
[size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-



And dmesg shows:

NET: Registered protocol family 10
Disabled Privacy Extensions on device c0340020(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
eth0: no IPv6 routers present
Freed a Wildcard
Unregistered Tormenta2
Zapata Telephony Interface Unloaded
Zapata Telephony Interface Registered on major 196
Zaptel Version:  Echo Canceller: KB1
Registered Tormenta2 PCI
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 201
Failed to initailize DAA, giving up...
wcfxo: probe of 0000:02:01.0 failed with error -5
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
wcfxo: DAA mode is 'FCC'
Found a Wildcard FXO: Generic Clone
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)
Registered tone zone 0 (United States / North America)


Any ideas?

-- 
Guillermo Salas M.
Telconet S.A. Manta
Calle 15 y Av. 24 Esq.
Phone : 593 5 262 8071
Mobile: 593 9 985 5138
SIP   : 105@sip.manta.telconet.net
e-mail: gsalas@manta.telconet.net
www   : http://www.telconet.net
        http://www.telcocarrier.net

Linux User: 255902
Soporte en Linea en http://www.manta.telconet.net

Please avoid sending me Word or PowerPoint attachments.
See http://www.fsf.org/philosophy/no-word-attachments.html

Mojo with Horan & Company, LLC

2006-Mar-06 16:11 UTC

head link

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

in zaptel.conf, you have fxsks=1 -- this only allocates the first card. 
  try fxsks=1-2 instead.


Guillermo Salas M wrote:> Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp
>  kernel. 
> 
> I've two x100p cards connected, only one card is reconigzed by
asterisk.
> 
> 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
> compatible 10/100 Ethernet (rev 31)
> 02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 
> This is the cli output for zap show channels :
> 
> My /etc/zaptel.conf :
> 
> # Zaptel Configuration File
> #
> # This file is parsed by the Zaptel Configurator, ztcfg
> #
> 
> # It must be in the module loading order
> 
> 
> # Span 1: WCFXO/1 "Generic Clone Board 2"
> fxsks=1
> 
> # Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> # Global data
> 
> loadzone        = us
> defaultzone     = us
> 
> 
> My /etc/asterisk/zapata-auto.conf
> 
> ; Zaptel Channels Configurations (zapata.conf)
> ;
> ; This is not intended to be a complete zapata.conf. Rather, it is
> intended
> ; to be #include-d by /etc/zapata.conf that will include the global
> settings
> ;
> callerid=asreceived
> 
> ; Span 1: WCFXO/1 "Generic Clone Board 2"
> signalling=fxs_ks
> ; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 1
> context=from-pstn
> group=0
> channel => 1
> 
> 
> ; Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> 
> This is the corresponding 'lspci -vv -n' for my two cards:
> 
> 02:01.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 201
>         Region 0: I/O ports at b800 [size=256]
>         Region 1: Memory at feaff000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 02:03.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 177
>         Region 0: I/O ports at b000 [size=256]
>         Region 1: Memory at feafd000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 
> And dmesg shows:
> 
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0340020(lo)
> IPv6 over IPv4 tunneling driver
> divert: not allocating divert_blk for non-ethernet device sit0
> eth0: no IPv6 routers present
> Freed a Wildcard
> Unregistered Tormenta2
> Zapata Telephony Interface Unloaded
> Zapata Telephony Interface Registered on major 196
> Zaptel Version:  Echo Canceller: KB1
> Registered Tormenta2 PCI
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 201
> Failed to initailize DAA, giving up...
> wcfxo: probe of 0000:02:01.0 failed with error -5
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
> wcfxo: DAA mode is 'FCC'
> Found a Wildcard FXO: Generic Clone
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> 
> 
> Any ideas?
> 
-- 
Mojo <mojo@horanappraisals.com>
Office Manger, Horan & Company, LLC
(907) 747-6666 x112

Mojo with Horan & Company, LLC

2006-Mar-06 16:13 UTC

head link

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

forgot to add this -- after the change in zaptel.conf, you would want to 
put a "channel => 2" in zapata.conf right after the "channel
=> 1" at
the bottom.

Now asterisk can actually see it.

Guillermo Salas M wrote:> Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp
>  kernel. 
> 
> I've two x100p cards connected, only one card is reconigzed by
asterisk.
> 
> 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
> compatible 10/100 Ethernet (rev 31)
> 02:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
> Modem/ISDN interface
> 
> This is the cli output for zap show channels :
> 
> My /etc/zaptel.conf :
> 
> # Zaptel Configuration File
> #
> # This file is parsed by the Zaptel Configurator, ztcfg
> #
> 
> # It must be in the module loading order
> 
> 
> # Span 1: WCFXO/1 "Generic Clone Board 2"
> fxsks=1
> 
> # Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> # Global data
> 
> loadzone        = us
> defaultzone     = us
> 
> 
> My /etc/asterisk/zapata-auto.conf
> 
> ; Zaptel Channels Configurations (zapata.conf)
> ;
> ; This is not intended to be a complete zapata.conf. Rather, it is
> intended
> ; to be #include-d by /etc/zapata.conf that will include the global
> settings
> ;
> callerid=asreceived
> 
> ; Span 1: WCFXO/1 "Generic Clone Board 2"
> signalling=fxs_ks
> ; Note: this is a trunk. Create a ZAP trunk in AMP for Channel 1
> context=from-pstn
> group=0
> channel => 1
> 
> 
> ; Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> 
> This is the corresponding 'lspci -vv -n' for my two cards:
> 
> 02:01.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 201
>         Region 0: I/O ports at b800 [size=256]
>         Region 1: Memory at feaff000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 02:03.0 Class 0780: e159:0001
>         Subsystem: 8086:0003
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
>         Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>         Latency: 32 (250ns min, 32000ns max)
>         Interrupt: pin A routed to IRQ 177
>         Region 0: I/O ports at b000 [size=256]
>         Region 1: Memory at feafd000 (32-bit, non-prefetchable)
> [size=4K]
>         Capabilities: [40] Power Management version 2
>                 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0
> +,D1-,D2+,D3hot+,D3cold+)
>                 Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 
> 
> And dmesg shows:
> 
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0340020(lo)
> IPv6 over IPv4 tunneling driver
> divert: not allocating divert_blk for non-ethernet device sit0
> eth0: no IPv6 routers present
> Freed a Wildcard
> Unregistered Tormenta2
> Zapata Telephony Interface Unloaded
> Zapata Telephony Interface Registered on major 196
> Zaptel Version:  Echo Canceller: KB1
> Registered Tormenta2 PCI
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 201
> Failed to initailize DAA, giving up...
> wcfxo: probe of 0000:02:01.0 failed with error -5
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 177
> wcfxo: DAA mode is 'FCC'
> Found a Wildcard FXO: Generic Clone
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> Registered tone zone 0 (United States / North America)
> 
> 
> Any ideas?
> 
-- 
Mojo <mojo@horanappraisals.com>
Office Manger, Horan & Company, LLC
(907) 747-6666 x112

Apparently Analagous Threads

Search for more reasonably related threads

asterisk users - Mar 2006 - Problem getting two x200p cards working on 1.2.4

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

[Asterisk-Users] Problem getting two x200p cards working on 1.2.4

Apparently Analagous Threads