Hello again,
I tried with iommu=0 on the Xen command line, and everything boots up
just fine. I was / am hoping to use VT-d. Can anybody shed any light
as to whether this is a problem with, e.g., my RAID card, or something
more fundamental relating to storage controllers?
VT-d works on this system without the RAID card (despite the strange
messages in Xen''s output). I have successfully assigned a Broadcom
NetXtreme NIC to an HVM Windows guest.
Thanks!
-Jon
On Tue, Apr 13, 2010 at 11:13 AM, Jonathan McCune <jonmccune@cmu.edu>
wrote:> Hello,
>
> I''m using Xen 4.0.0 compiled from source with the 2.6.31.13 kernel
> that it pulls down on its own. I added support for the aacraid driver
> to the kernel using ''make menuconfig'' from the
> build-linux-2.6-pvops_x86_64 subdirectory, and then built and
> installed the whole thing using ''make install'' from the
xen-4.0.0
> directory. I compiled this support natively, so I am not using an
> initrd. I''m fairly confident that I''ve compiled the
kernel correctly
> because it boots without Xen. With Xen, I am unable to boot fully
> because the linux kernel gets stuck because it has no root filesystem.
> This I surmise is because the aacraid driver is not initializing
> correctly.
>
> I logged the linux kernel messages via the serial port both with and
> without Xen, and narrowed down the first disk-related difference
> between them.
>
> WORKING, NON-XEN:
>
> [ 3.141977] Adaptec aacraid driver 1.1-5[2461]-ms
> [ 3.146768] aacraid 0000:02:0e.0: PCI INT A -> GSI 18 (level, low)
-> IRQ 18
> [ 3.155385] IRQ 18/aacraid: IRQF_DISABLED is not guaranteed on shared
IRQs
> [ 3.352307] AAC0: kernel 5.2-0[15323] Sep 21 2007
> [ 3.357084] AAC0: monitor 5.2-0[15323]
> [ 3.360905] AAC0: bios 5.2-0[15323]
> [ 3.364466] AAC0: serial 7C3110F43BB
> [ 3.368113] AAC0: Non-DASD support enabled.
> [ 3.372366] AAC0: 64bit support enabled.
> [ 3.376360] AAC0: 64 Bit DAC enabled
> [ 3.387168] scsi0 : aacraid
> [ 3.390319] scsi 0:0:1:0: Direct-Access Adaptec ArraySAS
> V1.0 PQ: 0 ANSI: 2
> [ 3.404997] scsi 0:1:0:0: Direct-Access FUJITSU MAX3147RC
> 0104 PQ: 0 ANSI: 3
>
>
> BROKEN, WITH-XEN:
>
> [ 3.424099] Adaptec aacraid driver 1.1-5[2461]-ms
> [ 3.428901] xen_set_ioapic_routing: irq 18 gsi 18 vector 18 ioapic
> 0 pin 18 triggering 1 polarity 1
> [ 3.438085] aacraid 0000:02:0e.0: PCI INT A -> GSI 18 (level, low)
-> IRQ 18
> [ 3.447573] IRQ 18/aacraid: IRQF_DISABLED is not guaranteed on shared
IRQs
> [ 3.644349] AAC0: kernel 5.2-0[15323] Sep 21 2007
> [ 3.649161] AAC0: monitor 5.2-0[15323]
> [ 3.653013] AAC0: bios 5.2-0[15323]
> [ 3.656602] AAC0: serial 7C3110F43BB
> [ 3.660277] AAC0: Non-DASD support enabled.
> [ 3.664560] AAC0: 64bit support enabled.
> [ 3.668557] AAC0: 64 Bit DAC enabled
> [ 3.679626] scsi0 : aacraid
> [ 3.683518] scsi 0:0:1:0: Direct-Access Adaptec ArraySAS
> V1.0 PQ: 0 ANSI: 2
> [ 3.700562] scsi scan: INQUIRY result too short (5), using 36
> [ 3.706381] scsi 0:1:0:0: Direct-Access
> PQ: 0 ANSI: 0
>
> For some reason if I enable serial output for the Xen kernel then it
> prevents the linux kernel''s serial messages from appearing. Thus,
> these Xen bootup messages are from a different boot (not sure why it
> would matter), but the failure mode is identical:
>
> __ __ _ _ ___ ___
> \ \/ /___ _ __ | || | / _ \ / _ \
> \ // _ \ ''_ \ | || |_| | | | | | |
> / \ __/ | | | |__ _| |_| | |_| |
> /_/\_\___|_| |_| |_|(_)___(_)___/
>
> (XEN) Xen version 4.0.0 (root@) (gcc version 4.3.2 (Debian 4.3.2-1.1)
> ) Tue Apr 13 09:08:06 EDT 2010
> (XEN) Latest ChangeSet: unavailable
> (XEN) Command line: iommu=1 com1=115200,8n1 console=com1,vga
> (XEN) Video information:
> (XEN) VGA is text mode 80x25, font 8x16
> (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds
> (XEN) Disc information:
> (XEN) Found 1 MBR signatures
> (XEN) Found 1 EDD information structures
> (XEN) Xen-e820 RAM map:
> (XEN) 0000000000000000 - 000000000009c400 (usable)
> (XEN) 000000000009c400 - 00000000000a0000 (reserved)
> (XEN) 00000000000e8000 - 0000000000100000 (reserved)
> (XEN) 0000000000100000 - 00000000db7ad440 (usable)
> (XEN) 00000000db7ad440 - 00000000db7af4a0 (ACPI NVS)
> (XEN) 00000000db7af4a0 - 00000000e0000000 (reserved)
> (XEN) 00000000f4000000 - 00000000f8000000 (reserved)
> (XEN) 00000000fe000000 - 00000000fed40000 (reserved)
> (XEN) 00000000fed45000 - 0000000100000000 (reserved)
> (XEN) 0000000100000000 - 00000001fc000000 (usable)
> (XEN) 00000001fc000000 - 0000000200000000 (reserved)
> (XEN) 0000000200000000 - 000000021c000000 (usable)
> (XEN) ACPI: RSDP 000E5410, 0014 (r0 COMPAQ)
> (XEN) ACPI: RSDT DB7D1540, 0044 (r1 HPQOEM SLIC-BPC 20091216 0)
> (XEN) ACPI: FACP DB7D15E8, 0074 (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) ACPI Warning (tbfadt-0444): Optional field
"Pm2ControlBlock" has
> zero address or length: 0000000000000050/0 [20070126]
> (XEN) ACPI: DSDT DB7D1A4F, A606 (r1 COMPAQ DSDT_PRJ 1 MSFT 100000E)
> (XEN) ACPI: FACS DB7D1500, 0040
> (XEN) ACPI: APIC DB7D165C, 00BC (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) ACPI: ASF! DB7D1718, 0063 (r32 COMPAQ IBEXPEAK 1
0)
> (XEN) ACPI: MCFG DB7D177B, 003C (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) ACPI: TCPA DB7D17B7, 0032 (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) ACPI: SLIC DB7D17E9, 0176 (r1 HPQOEM SLIC-BPC 1 0)
> (XEN) ACPI: HPET DB7D195F, 0038 (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) ACPI: DMAR DB7D1997, 00B8 (r1 COMPAQ IBEXPEAK 1 0)
> (XEN) System RAM: 7964MB (8156060kB)
> (XEN) Domain heap initialised
> (XEN) Processor #0 6:5 APIC version 21
> (XEN) Processor #1 6:5 APIC version 21
> (XEN) Processor #4 6:5 APIC version 21
> (XEN) Processor #5 6:5 APIC version 21
> (XEN) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
> (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
> (XEN) Using scheduler: SMP Credit Scheduler (credit)
> (XEN) Detected 3457.923 MHz processor.
> (XEN) Initing memory sharing.
> (XEN) VMX: Supported advanced features:
> (XEN) - APIC MMIO access virtualisation
> (XEN) - APIC TPR shadow
> (XEN) - Extended Page Tables (EPT)
> (XEN) - Virtual-Processor Identifiers (VPID)
> (XEN) - Virtual NMI
> (XEN) - MSR direct-access bitmap
> (XEN) - Unrestricted Guest
> (XEN) HVM: ASIDs enabled.
> (XEN) HVM: VMX enabled
> (XEN) HVM: Hardware Assisted Paging detected.
> (XEN) Intel VT-d Snoop Control not supported.
> (XEN) Intel VT-d DMA Passthrough not supported.
> (XEN) Intel VT-d Queued Invalidation not supported.
> (XEN) Intel VT-d Interrupt Remapping not supported.
> (XEN) I/O virtualisation enabled
> (XEN) I/O virtualisation for PV guests disabled
> (XEN) Enabled directed EOI with ioapic_ack_old on!
> (XEN) Total of 4 processors activated.
> (XEN) ENABLING IO-APIC IRQs
> (XEN) -> Using old ACK method
> (XEN) TSC is reliable, synchronization unnecessary
> (XEN) Platform timer is 14.318MHz HPET
> ÿ(XEN) Brought up 4 CPUs
> (XEN) [VT-D]iommu.c:818: iommu_fault_status: Faul
>
>
> Yes, they stop like that. I don''t know what Xen does to the
serial
> port but it appears to stop working. I can make a video of the screen
> and manually harvest some more info if really necessary.
>
> Do I need to change some setting somewhere to tell the system to give
> the RAID card a little more time?
>
> I am using ''iommu=1'' on the Xen command line, but my
understanding is
> that such support is built into Xen 4.0 by default anyways. Is the
> IOMMU breaking things? Seems very odd to me since this kernel works
> fine without Xen.
>
> The RAID card I''m using is a PCIe Adaptec SAS-3405. The machine
is an
> HP Elite 8100 minitower desktop PC.
>
> Many thanks for any helpful hints or suggestions!
> -Jon
>
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users