similar to: [asterik-users] Installing PRI card

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

I have an Asterisk box running Fedora Core 4, Asterisk 1.4, Lippri, 1.4, and Zaptel 1.4 The Digium cards installed are TDM2400 and TE110P. Everything was working fine until I upgraded to zaptel 1.2.12 from 1.2.9 Now when I run ztcfg I get the following error message: (CAS signalling on span 2 conflicts with Clear channel on channel 40) --NOTE: signaling was spelled wrong in the error

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro

Hello, I'm trying to upgrade an Asterisk 1.2 linux box to Asterisk 1.4. I installed the following -rw-r--r-- 1 root root 10908541 Sep 21 13:25 asterisk-1.4.0- beta2.tar.gz -rw-r--r-- 1 root root 993921 Sep 21 13:25 asterisk-addons-1.4.0- beta1.tar.gz -rw-r--r-- 1 root root 80019 Sep 21 13:25 libpri-1.4.0-beta1.tar.gz -rw-r--r-- 1 root root 1523413 Sep 21 13:25

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Hello, I'm just starting out with asterisk and I'm playing around with the system. Currently I have a Digium TE210P connected to a PRI on the Asterisk server. I have a SIP soft phone on my laptop for testing that is working fine. When I try to place a call from my soft phone I get this from Asterisk: May 1 09:11:41 NOTICE[20098]: app_dial.c:1029 dial_exec_full: Unable to create

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15' Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered

I'm trying to get a Qwest PRI configured and working with my lab Asterisk server. They said that the switchtype is 5ess and the signaling is pri_cpe. My entries into zaptel.conf are: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us channels=1-23 And my entries in zapata.conf are: language=en context=telco-incoming switchtype=5ess signalling=pri_cpe

Have a new TE133 in a dell R320. dahdi_cfg -vvv shows: DAHDI Tools Version - 2.9.1 DAHDI Version: 2.9.1 Echo Canceller(s): Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02) Channel 03: Clear

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Hello, I just bought a TE121 T1/E1 card, and now trying to install it on a 1.4.23.1 asterisk with dahdi 2.1.0.4 Actually first everything went on well and i managed to see my card on dahdi. Here's the output: #asterisk# dahdi_hardware pci:0000:04:08.0 wcte12xp+ d161:8000 Wildcard TE121 and this is the scan: -------------------------- asterisk# dahdi_scan [1] active=yes alarms=RED