similar to: Bad Line Noise over T1

Hey All, I have an Asterisk box connected to a Nortel Option 11C via a T1. In the Asterisk box we have a Sangoma A101C and in the Nortel we have a TMDI card. The Nortel is also hooked to the PSTN via a T1 on a different NTAK09 PRI card. I've included the Zapata.conf and zaptel.conf files below. Our issue is that when a call is sent over the tie line between the two systems, the audio on the

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hello All Any body used sangoma card A101. I have problem with this card. My system are: Linux Redhat 8.0. asterisk 1.07 and libpri, zaptel,... i connected E1 and MF/R2 signalling. i configure HDLC and TDM Voice. this is my configure as belows: #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Sun May

Hello, I'm fairly new to asterisk and Trixbox, I'm setting up a Trixbox based email to fax gateway. At this time, I have a ZAP PRI link between the eFax server and my VoIPSwitch. The ZAP channels are configured, the B and D channels are up, and I have green link lights on either end of my cabling, but when I dial the number I have assigned to my eFax server, the call never seems to route

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Hello, I have another little problem with my ZAPs channels, in fact, when I received a call, I heard no sound while in the CLI, sound is played: -- Starting simple switch on 'Zap/4-1' -- Executing [s at from-zaptel:1] Answer("Zap/4-1", "") in new stack -- Executing [s at from-zaptel:2] BackGround("Zap/4-1", "hello-world") in new stack --

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

I'm running Trixbox 1.2.3 with 2 TDM400s (FXOs). With Trixbox out of the mix and a regular phone connected I get the CID fine yet Trixbox shows 'unknown': dialparties.agi: Caller ID name is 'unknown' number is 'unknown' dialparties.agi: Methodology of ring is 'ringall' Here is my Zapata.conf if it helps: ############################# ; ; Zapata telephony

Can't get a Digium TDM04B working. Asterisk is running. I seem to have setup the trunks OK. But whenever I make an outgoing call get the 'all circuits are busy now' message. If I call in nothing happens at all! Here is my zapata.conf file: ; ; Zapata telephony interface ; ; Configuration file [trunkgroups] [channels] language=en context=from-pstn signalling=fxs_ks fxsks=1-4

Hey all, posted this the other day, but re-read it & realized I didn't give enough info to be useful.. so I thought I'd try again.. I'm using AAH 2.0 (* 1.2.0) and am unable to transfer a call when I initiate the outgoing call. In AMPs general settings, I've tried changing the Dial command using tT but transfers are only available when I'm the recipient of the call, not

Hi, I am using asterisk 1.2.5 and have some problems with asterisk connected with an E1 card to our PRI. Dialling in and out generally works. When someone dials in from a mobile phone, all numbers are sent as a block, and the called extension rings as intended. when someone picks up his phone handset, waits for a dial tone, and then dials in manually, the call will be redirected to the

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I've been going nuts lately trying to get rid of an annoying echo problem that makes my asterisk server unusable when clients try to call me. Here's the breakdown of the issue - Hoping that someone can throw me a clue: My setup is as such: Single AMD Athon machine with X100P clone card and voip through multiple providers . * Inbound calls through the X100P that do not bridge to

I've spent all day today trying to fix an echo problem and I've made no ground whatsoever. I have Digium TDM400 with 3 FXO & 1 FXS. I've tried this computer at two completely different sites with different phone providers. I've tried compiling & installing different versions of Zaptel (currently running 1.4.0, started at 1.2.9 and worked my way up). I've tried

Hi, I am trying to configure * 1.0.7 box with a Digium Wildcard TE110P T1/E1 and libunicall latest code. All libs compiled successfully and the E1 have a green light! I am able to receive a call (or at least) testcall shows some information when an incoming call is received so the drivers and basic configuration is working. My * box has 2 cards, one TDM400B (2 fxs and 2 fxo) and one TE110P

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hi all I wonder if anyone can give a little insight into this; asterisk@home 2.2, HP Proliant gl3, sangoma A101,Cable and Wireless, ISDN30. 10 zactive channels Incoming calls work fine no problems tested 43 DIDs all working. zaptel.conf # Global data loadzone = uk defaultzone = uk span=1,1,0,ccs,hdb3,crc4 bchan=1-10 dchan=16 zapata.conf [channels] language=en context=from-pstn

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

Hi *, now for a long time i am trying to set the outgoing callerid, without luck. I am here in Germany, my asterisk has a pri interface connected to a PMX installed by Telekom. All telephone calls are preselected to EcoVoice. I am using asterisk 1.2.7.1, zaptel 1.2.5 and libpri 1.2.2. A week ago we tried with a device able to simulate a telephone system so send out a callerid, and that