Anderson Ling
2006-Jun-06 23:46 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel configurations. asterisk version: 1.2.9.1 Zaptel Version: 1.2.6 Echo Canceller: KB1 # Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1" fxsks=1 fxsks=2 fxsks=3 fxsks=4 fxsks=5 | | fxsks=21 fxsks=22 fxsks=23 fxsks=24 # Global data loadzone = us defaultzone = us [root#] lspci -vb 06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11) Subsystem: Digium, Inc. Wildcard TDM2400P Flags: bus master, medium devsel, latency 32, IRQ 3 I/O ports at b800 Memory at ff520000 (32-bit, non-prefetchable) Expansion ROM at ff500000 [disabled] Capabilities: [c0] Power Management version 2 [root#] dmesg --------snip ----------- Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.6 Echo Canceller: KB1 PCI: Found IRQ 3 for device 0000:06:00.0 PCI Config reg is 02900117 WCTDM2400P: New Reg: fe590000! Detected REG0: 00000100 Detected REG1: 00007849 Detected REG2: 0000001d (pre) Reg fc is 50000027 (post) Reg fc is 50000024 Detected REG2: 0000ffff wctdm2400p: reg is a04c0004 Resetting the modules... During Resetting the modules... After resetting the modules... Port 1: Installed -- AUTO FXO (MALAYSIA mode) Port 2: Installed -- AUTO FXO (MALAYSIA mode) Port 3: Installed -- AUTO FXO (MALAYSIA mode) Port 4: Installed -- AUTO FXO (MALAYSIA mode) Port 5: Installed -- AUTO FXO (MALAYSIA mode) Port 6: Installed -- AUTO FXO (MALAYSIA mode) Port 7: Installed -- AUTO FXO (MALAYSIA mode) Port 8: Installed -- AUTO FXO (MALAYSIA mode) Port 9: Installed -- AUTO FXO (MALAYSIA mode) Port 10: Installed -- AUTO FXO (MALAYSIA mode) Port 11: Installed -- AUTO FXO (MALAYSIA mode) Port 12: Installed -- AUTO FXO (MALAYSIA mode) Port 13: Installed -- AUTO FXO (MALAYSIA mode) Port 14: Installed -- AUTO FXO (MALAYSIA mode) Port 15: Installed -- AUTO FXO (MALAYSIA mode) Port 16: Installed -- AUTO FXO (MALAYSIA mode) Port 17: Installed -- AUTO FXO (MALAYSIA mode) Port 18: Installed -- AUTO FXO (MALAYSIA mode) Port 19: Installed -- AUTO FXO (MALAYSIA mode) Port 20: Installed -- AUTO FXO (MALAYSIA mode) Port 21: Installed -- AUTO FXO (MALAYSIA mode) Port 22: Installed -- AUTO FXO (MALAYSIA mode) Port 23: Installed -- AUTO FXO (MALAYSIA mode) Port 24: Installed -- AUTO FXO (MALAYSIA mode) VPM Revision: 01 VPM: U-law mode VPM: DTMF threshold set to 1250 VPM: Present and operational (Rev B) Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules) Registered tone zone 0 (United States / North America) ----------- snip --------------- [root]# cat zapata.conf [trunkgroups] [channels] language=en context=from-zaptel signalling=fxs_ks rxwink=300 ; Atlas seems to use long (250ms) winks ; ; Whether or not to do distinctive ring detection on FXO lines ; ;usedistinctiveringdetection=yes usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=no echotraining=800 rxgain=0.0 txgain=0.0 group=0 callgroup=1 pickupgroup=1 immediate=no useincomingcalleridonzaptransfer=yes busycount=4 callprogress = yes ;faxdetect=both ;faxdetect=incoming ;faxdetect=outgoing ;faxdetect=no ;Include genzaptelconf configs #include zapata-auto.conf group=1 ;Include AMP configs #include zapata_additional.conf
Anderson Ling
2006-Jun-07 21:37 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
Looks like no body know this> Hi all, > I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in > my office. the out going calls symptom like when called party pickup > the phone but the calling party still hearing the ring tone from the > IP phone. > Please light me up. it been many sleepless night by googling around > trying to get the right answers. > > The digium card running on Intel 915G chipset. Below are my zaptel > configurations. > asterisk version: 1.2.9.1 > Zaptel Version: 1.2.6 Echo Canceller: KB1 > # Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1" > fxsks=1 > fxsks=2 > fxsks=3 > fxsks=4 > fxsks=5 > | > | > fxsks=21 > fxsks=22 > fxsks=23 > fxsks=24 > > # Global data > loadzone = us > defaultzone = us > > [root#] lspci -vb > > 06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11) > Subsystem: Digium, Inc. Wildcard TDM2400P > Flags: bus master, medium devsel, latency 32, IRQ 3 > I/O ports at b800 > Memory at ff520000 (32-bit, non-prefetchable) > Expansion ROM at ff500000 [disabled] > Capabilities: [c0] Power Management version 2 > > [root#] dmesg > > --------snip ----------- > Zapata Telephony Interface Registered on major 196 > Zaptel Version: 1.2.6 Echo Canceller: KB1 > PCI: Found IRQ 3 for device 0000:06:00.0 > PCI Config reg is 02900117 > WCTDM2400P: New Reg: fe590000! > Detected REG0: 00000100 > Detected REG1: 00007849 > Detected REG2: 0000001d > (pre) Reg fc is 50000027 > (post) Reg fc is 50000024 > Detected REG2: 0000ffff > wctdm2400p: reg is a04c0004 > Resetting the modules... > During Resetting the modules... > After resetting the modules... > Port 1: Installed -- AUTO FXO (MALAYSIA mode) > Port 2: Installed -- AUTO FXO (MALAYSIA mode) > Port 3: Installed -- AUTO FXO (MALAYSIA mode) > Port 4: Installed -- AUTO FXO (MALAYSIA mode) > Port 5: Installed -- AUTO FXO (MALAYSIA mode) > Port 6: Installed -- AUTO FXO (MALAYSIA mode) > Port 7: Installed -- AUTO FXO (MALAYSIA mode) > Port 8: Installed -- AUTO FXO (MALAYSIA mode) > Port 9: Installed -- AUTO FXO (MALAYSIA mode) > Port 10: Installed -- AUTO FXO (MALAYSIA mode) > Port 11: Installed -- AUTO FXO (MALAYSIA mode) > Port 12: Installed -- AUTO FXO (MALAYSIA mode) > Port 13: Installed -- AUTO FXO (MALAYSIA mode) > Port 14: Installed -- AUTO FXO (MALAYSIA mode) > Port 15: Installed -- AUTO FXO (MALAYSIA mode) > Port 16: Installed -- AUTO FXO (MALAYSIA mode) > Port 17: Installed -- AUTO FXO (MALAYSIA mode) > Port 18: Installed -- AUTO FXO (MALAYSIA mode) > Port 19: Installed -- AUTO FXO (MALAYSIA mode) > Port 20: Installed -- AUTO FXO (MALAYSIA mode) > Port 21: Installed -- AUTO FXO (MALAYSIA mode) > Port 22: Installed -- AUTO FXO (MALAYSIA mode) > Port 23: Installed -- AUTO FXO (MALAYSIA mode) > Port 24: Installed -- AUTO FXO (MALAYSIA mode) > VPM Revision: 01 > VPM: U-law mode > VPM: DTMF threshold set to 1250 > VPM: Present and operational (Rev B) > Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules) > Registered tone zone 0 (United States / North America) > ----------- snip --------------- > > [root]# cat zapata.conf > [trunkgroups] > [channels] > language=en > context=from-zaptel > signalling=fxs_ks > rxwink=300 ; Atlas seems to use long (250ms) winks > ; > ; Whether or not to do distinctive ring detection on FXO lines > ; > ;usedistinctiveringdetection=yes > > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=no > echotraining=800 > rxgain=0.0 > txgain=0.0 > group=0 > callgroup=1 > pickupgroup=1 > immediate=no > useincomingcalleridonzaptransfer=yes > busycount=4 > callprogress = yes > > ;faxdetect=both > ;faxdetect=incoming > ;faxdetect=outgoing > ;faxdetect=no > > ;Include genzaptelconf configs > #include zapata-auto.conf > > group=1 > > ;Include AMP configs > #include zapata_additional.conf > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > >
Time Bandit
2006-Jun-07 22:03 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
> Looks like no body know thisI think your problem is right there in zapata.conf :> > callprogress = yesset it to no. Asterisk think that the other end as not answered yet. If you stay on the line (ignoring the ringing) you will be disconnected after you dial timeout parameter. hth
Tzafrir Cohen
2006-Jun-07 22:09 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
On Wed, Jun 07, 2006 at 02:46:41PM +0800, Anderson Ling wrote:> Hi all, > I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in > my office. the out going calls symptom like when called party pickup the > phone but the calling party still hearing the ring tone from the IP phone. > Please light me up. it been many sleepless night by googling around > trying to get the right answers.First off, your post does not include the complete chan_zap configuration: zapata_auto and zapata_additional are still missing. Also: what do you see in the CLI as the output of the cmmand 'show channes' when there is such a call?> > The digium card running on Intel 915G chipset. Below are my zaptel > configurations. > asterisk version: 1.2.9.1 > Zaptel Version: 1.2.6 Echo Canceller: KB1 > # Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1" > fxsks=1 > fxsks=2 > fxsks=3 > fxsks=4 > fxsks=5 > | > | > fxsks=21 > fxsks=22 > fxsks=23 > fxsks=24 > > # Global data > loadzone = us > defaultzone = us > > [root#] lspci -vb > > 06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11) > Subsystem: Digium, Inc. Wildcard TDM2400P > Flags: bus master, medium devsel, latency 32, IRQ 3 > I/O ports at b800 > Memory at ff520000 (32-bit, non-prefetchable) > Expansion ROM at ff500000 [disabled] > Capabilities: [c0] Power Management version 2 > > [root#] dmesg > > --------snip ----------- > Zapata Telephony Interface Registered on major 196 > Zaptel Version: 1.2.6 Echo Canceller: KB1 > PCI: Found IRQ 3 for device 0000:06:00.0 > PCI Config reg is 02900117 > WCTDM2400P: New Reg: fe590000! > Detected REG0: 00000100 > Detected REG1: 00007849 > Detected REG2: 0000001d > (pre) Reg fc is 50000027 > (post) Reg fc is 50000024 > Detected REG2: 0000ffff > wctdm2400p: reg is a04c0004 > Resetting the modules... > During Resetting the modules... > After resetting the modules... > Port 1: Installed -- AUTO FXO (MALAYSIA mode) > Port 2: Installed -- AUTO FXO (MALAYSIA mode) > Port 3: Installed -- AUTO FXO (MALAYSIA mode) > Port 4: Installed -- AUTO FXO (MALAYSIA mode) > Port 5: Installed -- AUTO FXO (MALAYSIA mode) > Port 6: Installed -- AUTO FXO (MALAYSIA mode) > Port 7: Installed -- AUTO FXO (MALAYSIA mode) > Port 8: Installed -- AUTO FXO (MALAYSIA mode) > Port 9: Installed -- AUTO FXO (MALAYSIA mode) > Port 10: Installed -- AUTO FXO (MALAYSIA mode) > Port 11: Installed -- AUTO FXO (MALAYSIA mode) > Port 12: Installed -- AUTO FXO (MALAYSIA mode) > Port 13: Installed -- AUTO FXO (MALAYSIA mode) > Port 14: Installed -- AUTO FXO (MALAYSIA mode) > Port 15: Installed -- AUTO FXO (MALAYSIA mode) > Port 16: Installed -- AUTO FXO (MALAYSIA mode) > Port 17: Installed -- AUTO FXO (MALAYSIA mode) > Port 18: Installed -- AUTO FXO (MALAYSIA mode) > Port 19: Installed -- AUTO FXO (MALAYSIA mode) > Port 20: Installed -- AUTO FXO (MALAYSIA mode) > Port 21: Installed -- AUTO FXO (MALAYSIA mode) > Port 22: Installed -- AUTO FXO (MALAYSIA mode) > Port 23: Installed -- AUTO FXO (MALAYSIA mode) > Port 24: Installed -- AUTO FXO (MALAYSIA mode) > VPM Revision: 01 > VPM: U-law mode > VPM: DTMF threshold set to 1250 > VPM: Present and operational (Rev B) > Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules) > Registered tone zone 0 (United States / North America) > ----------- snip --------------- > > [root]# cat zapata.conf > [trunkgroups] > [channels] > language=en > context=from-zaptel > signalling=fxs_ks > rxwink=300 ; Atlas seems to use long (250ms) winks > ; > ; Whether or not to do distinctive ring detection on FXO lines > ; > ;usedistinctiveringdetection=yes > > usecallerid=yes > hidecallerid=no > callwaiting=yes > usecallingpres=yes > callwaitingcallerid=yes > threewaycalling=yes > transfer=yes > cancallforward=yes > callreturn=yes > echocancel=yes > echocancelwhenbridged=no > echotraining=800 > rxgain=0.0 > txgain=0.0 > group=0 > callgroup=1 > pickupgroup=1 > immediate=no > useincomingcalleridonzaptransfer=yes > busycount=4 > callprogress = yes > > ;faxdetect=both > ;faxdetect=incoming > ;faxdetect=outgoing > ;faxdetect=no > > ;Include genzaptelconf configs > #include zapata-auto.conf > > group=1 > > ;Include AMP configs > #include zapata_additional.conf > > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >-- Tzafrir Cohen sip:tzafrir@local.xorcom.com icq#16849755 iax:tzafrir@local.xorcom.com +972-50-7952406 tzafrir.cohen@xorcom.com http://www.xorcom.com
El Flynn
2006-Jun-07 22:31 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
Anderson Ling wrote:> Hi all, > I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in > my office. the out going calls symptom like when called party pickup the > phone but the calling party still hearing the ring tone from the IP phone. > Please light me up. it been many sleepless night by googling around > trying to get the right answers. > > [root]# cat zapata.conf<snip>> callgroup=1 > pickupgroup=1 > immediate=no > useincomingcalleridonzaptransfer=yes > busycount=4 > callprogress = yes >You might not want to use callprogress, as this is more related to US type of call progress analysis. The tones are different in Malaysia. Flynn
Anderson Ling
2006-Jun-08 22:24 UTC
[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.
Hi Flynn, Thanks for your reply, after changing the callprogress =no the zap lines are working fine now. Thank you very much. anderson El Flynn wrote:> Anderson Ling wrote: >> Hi all, >> I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting >> in my office. the out going calls symptom like when called party >> pickup the phone but the calling party still hearing the ring tone >> from the IP phone. >> Please light me up. it been many sleepless night by googling around >> trying to get the right answers. >> >> [root]# cat zapata.conf > <snip> >> callgroup=1 >> pickupgroup=1 >> immediate=no >> useincomingcalleridonzaptransfer=yes >> busycount=4 >> callprogress = yes >> > > You might not want to use callprogress, as this is more related to US > type of call progress analysis. The tones are different in Malaysia. > > Flynn > > > >