Displaying 20 results from an estimated 4000 matches similar to: "Problem selecting E1 on TE405P"
2004 Dec 21
2
TE405P E1 coax cables with balun
Hi,
I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in
on a pair of RG-59 coax cables with BNC connectors. So I need an
adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am
not sure that It works. I have configured my asterisk in this way:
zaptel.conf
span=1,1,0,ccs,hdb3,crc4
dchan=16
bchan=1-15,17-31
loadzone=it
defaultzone=it
zapata.conf
2005 Feb 23
2
Trouble installing TE405P with asterisk@home
I successfully installed asterisk@home 0.6, but when i try to load the
wct4xxp module for the TE405P I just got, I get the following:
Found TE410P at base address fb7ffc00, remapped to e0220c00
TE410P version c01a009b
Tried to load 1c8ac800 into 00000000, but got 188ac800 instead
Tried to load 1c8ac000 into 00000001, but got 188ac000 instead
Tried to load 07fc07fc into 00000002, but got 03fc07fc
2004 Jul 18
1
TE405P
I'm installing TE405P card.
This is my zaptel.conf.
--------------------------------------
span=1,0,0,ccs,hdb3,crc4
span=2,1,0,ccs,hdb3,crc4
span=3,0,0,ccs,hdb3,crc4
span=4,0,0,ccs,hdb3,crc4
loadzone = us
defaultzone= us
--------------------------------------
When i modprobe wct4xxp,
--------------------------------------
PCI: Found IRQ 11 for device 02:0b.0
PCI: Sharing IRQ 11 with
2003 Sep 25
3
configuring TE410P for four E1 PRI lines
hi,
I'm trying to configure my newly acquired TE410P card to work as 4
E1 spans. This is
supposed to be a drop-in replacement to the earlier E100P card. However,
on loading the
zaptel module it gets configured as T1 spans basically doing a 'cat' on
/proc/zaptel/1 thru 4,
it shows 24 channels per span. After this ztcfg fails saying
'ZT_CHANCONFIG failed for channel 97'.
2005 Mar 14
3
Problem with TE405P and Slackware 10.0
Hi to all,
I have a problem with this wildcard and one E1 line.
The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The
kernel version is 2.4.26.
I have donwload and build the latest CVS version of zaptel, libpri and
asterisk following the ufficial instructions of digium.
I have set up my server in this way:
zaptel.conf
loadzone=it
defaultzone=it
2005 Jan 22
1
te405P and german PMX
Hi all,
i am stuck with the configuration of asterisk
- modules are loaded ( zaptel and wct4xxp )
- i have zaptel.conf configure, output of ztcfg -vv
--- snip --
rapid:~# ztcfg -vv
Zaptel Configuration
======================
SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1)
SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet
2004 Apr 30
1
Configuring Digium TE405P for use in Germany
Hello all,
I really checked voip-info.org but it still seems to be not very easy and I
just hope that there is anybody with a simular config.
We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second
PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper
than a channel bank :-)
Carrier ----S2M------ * -----S2M------Siemens
|
|
2006 Apr 28
1
RESOLVED - TE405P vs. SoundCard problem (in reality - TE405P No Voice Problem)
Forget the sound card. It isn't related. The subject above should have
read 'TE405P No Voice Problem' or something similar. It appears to be a
zaptel timing issue, but I have found a workaround. For those of you
just tuning in, here is the story:
I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap
1.2.5, both compiled from the source available off the main
2006 Feb 28
2
Problem with two cards Digium
Hello,
I`ve got a problem which I can`t deal with. I own 2 cards - TDM2400P and
TE410P. I`ve put them into a HP Proliant DL380 G4 server, compiled the
drivers according to the manual. Unfortunetly there are both cards
channels are configured in zaptel.conf file the first module (in this
file) sends an error.
For configuration:
span = 1, 1, 0, ccs, hdb3, crc4
fxsks = 21-24
bchan = 25-39,
2004 Jul 26
3
TE405P and E1
Hello
Im from Denmark and i've just got my Digium TE405P. But i have some
problems when i connect it to my E1 connection (ISDN30).
My telco delivered a alcatel box witch have a G.703 120ohm (DB9 with a
serial to rj45) and a 75ohm coax connection.
I've tried to connect using the 120ohm with rj45 and a ordinary utp cable.
But it dosent seem to work. I've tried several zaptel.conf
2007 Jan 31
2
no lights on TE405P, but shows up in lspci, modules loaded
I pulled a working TE405P from one box and put it in another box. I
compiled the zaptel modules, modprobe zaptel, modprobe wct4xxp, but no
lights on the card come on.
I do an lspci and the card shows up there.
I ran ztcfg -vv and got the error message Unable to open master device
'/dev/zap/ctl' so I followed the instructions in README.udev
the error message went away, but now when I
2004 Apr 15
2
TE405P + Adit 600 and FXO module - should this work?
Folks,
I'm experimenting with bringing multiple (8) analog lines from our local
telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
having this talk to Asterisk via the T1 TDM controller on the ADIT and a
TE405P card.
I don't know if this will work well (ie: give me decent echo cancellation,
call disconnect supervision, caller ID etc) but I haven't had much
2005 Jan 25
2
Problems splicing Asterisk with a TE405P between Arcor E1 PRI and Ericsson Business Phone 250
hi,
i'm having problems getting asterisk spliced between an E1 PRI (german
Telco Arcor) and an Ericsson Business Phone 250 digital PBX.
The Asterisk Server has a TE405P with it's port 1 connected to the E1
PRI provided by our telecommunications provider Arcor and port 2
connected to the E1 PRI of our Ericsson BP250.
the setup before:
Arcor TelCo PRI(E1)
2005 Jun 17
2
Can't switch span to E1-mode
Hi,
This error I got it just when I gonfigure zaptel support isdneuro 31
channels.
But if I configure zaptel to support T1 and just 24 channels I have no
problem.
########################################################################
####
#
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
#
loadzone = it
span=1,1,0,ccs,hdb3,crc4
bchan=1-23
dchan=16
2008 Nov 14
3
asterisk/E1
Dear All
I installed a Digium card TE405P with zaptel and its running successfully
with no alarms, but asterisk is not running .
Any one have a cure or advice
03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span
T1/E1/J1 card 5.0V (rev 02)
Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2
Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing
2006 Apr 27
2
TE405P vs. SoundCard problem
My Asterisk server believes that a Digium TE405P and sound are
incompatible. Basically, no matter what else I do to the machine it
terms of hardware, if the TE405P is installed, none of the
playback/background/etc commands work. MOH works fine.
So far, I have tried:
1) Seven different PCI soundcards with different chipsets. (Go go
Computer Junk Store!)
2) Disabling each and every device
2006 Dec 18
2
Digium TE405P with French E1 => Red Alert
Hi
anyone have a idea for debug my digium TE405P card ?
My zaptel.conf:
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone = fr
defaultzone = fr
My Zapata.conf:
[channels]
language=fr
context=from-E1
switchtype = euroisdn
pridialplan = unknown
signalling = pri_cpe
usecallerid=yes
hidecallerid=no
callwaiting=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
2004 Aug 12
5
Question about TE405P
Hi all,
Does somebody know how I have to setup my TE405P ?
Is it correct my configuration below ? Otherwise, can somebody help me ?
Thanks,
Angel.
zaptel.conf
span=1,1,0,ccs,hdb3
span=2,0,1,ccs,hdb3
span=3,0,1,ccs,hdb3
span=4,0,1,ccs,hdb3
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
2005 Mar 07
2
[Asterisk-Dev] TE405P/410P (Quad-T1/E1) driver
Hello,
I would like to know if FreeBSD has drivers for TE405P cards submitted
to the ports. I have acquired a card and would really like to use it
with FreeBSD. The wiki said the drivers havent been tested yet. Have
there been any updates since then?
regards
Kavit
_______________________________________________
Asterisk-Dev mailing list
Asterisk-Dev@lists.digium.com
2006 Nov 22
5
TE110P and TDM400P
Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above:
0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b1d9:0003
Flags: bus master, medium devsel, latency 64, IRQ 169
I/O ports at e800 [size=256]