I successfully installed asterisk@home 0.6, but when i try to load the
wct4xxp module for the TE405P I just got, I get the following:
Found TE410P at base address fb7ffc00, remapped to e0220c00
TE410P version c01a009b
Tried to load 1c8ac800 into 00000000, but got 188ac800 instead
Tried to load 1c8ac000 into 00000001, but got 188ac000 instead
Tried to load 07fc07fc into 00000002, but got 03fc07fc instead
FALC version: 00000005, Board ID: 00
Reg 0: 0x188ac800
Reg 1: 0x188ac000
Reg 2: 0x03fc07fc
Reg 3: 0x00000000
Reg 4: 0x00000000
Reg 5: 0x00000000
Reg 6: 0xc01a009b
Reg 7: 0x00001f00
Reg 8: 0x00000000
Reg 9: 0x00ff0000
Reg 10: 0x00000000
TE410P: Launching card: 0
TE410P: Setting up global serial parameters
Found a Wildcard: Wildcard TE410P-Xilinx
Wildcard USB FXS Interface driver registered
This is if I haven't yet defined the channels in zatel.conf.
If I define them the system starts scrolling the main console with messages
like:
Tried to load 1c8ac000 into 00000001, but got 188ac000 instead
This goes on and on, and the only way to stop it is a hard reboot.
I don't think this is an IRQ problem - when I run cat /proc/interrupts I get
this:
CPU0 CPU1
0: 1905021 1902517 IO-APIC-edge timer
1: 119 77 IO-APIC-edge keyboard
2: 0 0 XT-PIC cascade
8: 1 0 IO-APIC-edge rtc
12: 1196 1188 IO-APIC-edge PS/2 Mouse
14: 2 0 IO-APIC-edge ide0
18: 0 0 IO-APIC-level t4xxp
19: 14144 10091 IO-APIC-level libata
20: 4208 0 IO-APIC-level eth0
23: 0 0 IO-APIC-level ehci-hcd
NMI: 0 0
LOC: 3807385 3807383
ERR: 0
MIS: 0
The system is a P4 3000 with 1GB RAM, Intel D915GAV Motherboard
Any help would be greatly appreciated.
Asterisk@Home
2005-Feb-23 22:30 UTC
[Asterisk-Users] Trouble installing TE405P with asterisk@home
did you try the auto-config? help-aah will tell you how to do this. --- BSDR <bsdr2@netvision.net.il> wrote:> I successfully installed asterisk@home 0.6, but when > i try to load the > wct4xxp module for the TE405P I just got, I get the > following: > > Found TE410P at base address fb7ffc00, remapped to > e0220c00 > TE410P version c01a009b > Tried to load 1c8ac800 into 00000000, but got > 188ac800 instead > Tried to load 1c8ac000 into 00000001, but got > 188ac000 instead > Tried to load 07fc07fc into 00000002, but got > 03fc07fc instead > FALC version: 00000005, Board ID: 00 > Reg 0: 0x188ac800 > Reg 1: 0x188ac000 > Reg 2: 0x03fc07fc > Reg 3: 0x00000000 > Reg 4: 0x00000000 > Reg 5: 0x00000000 > Reg 6: 0xc01a009b > Reg 7: 0x00001f00 > Reg 8: 0x00000000 > Reg 9: 0x00ff0000 > Reg 10: 0x00000000 > TE410P: Launching card: 0 > TE410P: Setting up global serial parameters > Found a Wildcard: Wildcard TE410P-Xilinx > Wildcard USB FXS Interface driver registered > > This is if I haven't yet defined the channels in > zatel.conf. > If I define them the system starts scrolling the > main console with messages > like: > Tried to load 1c8ac000 into 00000001, but got > 188ac000 instead > This goes on and on, and the only way to stop it is > a hard reboot. > > I don't think this is an IRQ problem - when I run > cat /proc/interrupts I get > this: > CPU0 CPU1 > 0: 1905021 1902517 IO-APIC-edge timer > 1: 119 77 IO-APIC-edge keyboard > 2: 0 0 XT-PIC cascade > 8: 1 0 IO-APIC-edge rtc > 12: 1196 1188 IO-APIC-edge PS/2 > Mouse > 14: 2 0 IO-APIC-edge ide0 > 18: 0 0 IO-APIC-level t4xxp > 19: 14144 10091 IO-APIC-level libata > 20: 4208 0 IO-APIC-level eth0 > 23: 0 0 IO-APIC-level ehci-hcd > NMI: 0 0 > LOC: 3807385 3807383 > ERR: 0 > MIS: 0 > > The system is a P4 3000 with 1GB RAM, Intel D915GAV > Motherboard > > Any help would be greatly appreciated. > > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com >http://lists.digium.com/mailman/listinfo/asterisk-users> To UNSUBSCRIBE or update options visit: > >http://lists.digium.com/mailman/listinfo/asterisk-users>__________________________________ Do you Yahoo!? Yahoo! Mail - 250MB free storage. Do more. Manage less. http://info.mail.yahoo.com/mail_250
Thanks for the reply.> did you try the auto-config? help-aah will tell you > how to do this.Yes I did. It put the span definitions etc. in zaptel.conf *as comments* (BTW, is this to be expected - that the defenitions are commented?), but if I uncomment those lines then the it starts giving me "Tried to load 1c8ac000 into 00000001, but got 188ac000 instead" or similar messages, and I have to to a hard reset to get out, as I wrote in my original post.