Darren Nickerson
2004-Apr-15 22:29 UTC
[Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
Folks,
I'm experimenting with bringing multiple (8) analog lines from our local
telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
having this talk to Asterisk via the T1 TDM controller on the ADIT and a
TE405P card.
I don't know if this will work well (ie: give me decent echo cancellation,
call disconnect supervision, caller ID etc) but I haven't had much luck
getting this combination flying at all thus far. Should it work?
I've been concentrating on the Adit T1 interface <----> TE405P
connection
... and have the following in zapata.conf:
span=1,1,0,esf,b8zs
fxsks=1-24
loadzone = us
defaultzone=us
At the end of my zaptel.conf, I have:
signalling=fxs_ks
group=2
callerid="Joe Schmoe" <(215) 555-1212>
channel => 1-24
To get things flying, I do:
modprobe zaptel
modprobe wct4xxp
which causes the TE405P card to activate, but show a single flashing red
alarm on the configured span.
The Adit's TDM controller also displays a solid red LED. Here's its
status:
Adit 600> status a:1
SLOT A:
Status for DS1 1:
Receive: Loss of Signal
Transmit: RAI/Yellow Alarm
Loopback: OFF
Adit 600>
I'm not sure I have the DS1 configured appropriately. It says:
Adit 600> show a:1
SLOT A:
Settings for DS1 1:
Circuit ID: CAC DS1# A:1
Up/Down: UP
Framing: ESF
Line Coding: B8ZS
Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB)
Loop Code Detection: ON
Loopback: OFF
FDL Type: None
Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors
here?
-Darren
--
Darren Nickerson
Senior Sales & Support Engineer
iFAX Solutions, Inc. www.ifax.com
darren.nickerson@ifax.com
+1.215.438.4638 ext 8106 office
+1.215.243.8335 fax
Paul Zimm
2004-Apr-16 05:05 UTC
[Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
I have an Adit 600 working with a TDM400p card.
- check this link for info on Adit-600 configuration
http://lists.digium.com/pipermail/asterisk-users/2003-June/013072.html
-Make sure the pinouts for your T1 cable are correct:
DigiumT1 -> RJ-48(F) X-over
Digium T1 Card Channel Bank RJ-48(F)
Pin Pair# T/R Color Pin T/R
1 2 T white/orange 4
R1
2 2 R orange/white 5 T
4 1 T blue/white 1
R
5 1 R white/blue 2
T1
3, 6, 7, 8 Not assigned
Darren Nickerson wrote:
>Folks,
>
>I'm experimenting with bringing multiple (8) analog lines from our local
>telco into a Carrier Access ADIT 600 channel bank with an FXO module, then
>having this talk to Asterisk via the T1 TDM controller on the ADIT and a
>TE405P card.
>
>I don't know if this will work well (ie: give me decent echo
cancellation,
>call disconnect supervision, caller ID etc) but I haven't had much luck
>getting this combination flying at all thus far. Should it work?
>
>I've been concentrating on the Adit T1 interface <----> TE405P
connection
>... and have the following in zapata.conf:
>
> span=1,1,0,esf,b8zs
> fxsks=1-24
> loadzone = us
> defaultzone=us
>
>At the end of my zaptel.conf, I have:
>
> signalling=fxs_ks
> group=2
> callerid="Joe Schmoe" <(215) 555-1212>
> channel => 1-24
>
>To get things flying, I do:
>
> modprobe zaptel
> modprobe wct4xxp
>
>which causes the TE405P card to activate, but show a single flashing red
>alarm on the configured span.
>
>The Adit's TDM controller also displays a solid red LED. Here's its
status:
>
> Adit 600> status a:1
> SLOT A:
> Status for DS1 1:
> Receive: Loss of Signal
> Transmit: RAI/Yellow Alarm
> Loopback: OFF
>
> Adit 600>
>
>I'm not sure I have the DS1 configured appropriately. It says:
>
> Adit 600> show a:1
> SLOT A:
> Settings for DS1 1:
> Circuit ID: CAC DS1# A:1
> Up/Down: UP
> Framing: ESF
> Line Coding: B8ZS
> Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB)
> Loop Code Detection: ON
> Loopback: OFF
> FDL Type: None
>
>Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors
>here?
>
>-Darren
>
>
>
Darren Nickerson
2004-Apr-16 05:33 UTC
[Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?
Thanks! I'll spend some time with this information, check the pinouts and I should be well on my way. Glad to know it can work! ;-) -Darren -- Darren Nickerson Senior Sales & Support Engineer iFAX Solutions, Inc. www.ifax.com darren.nickerson@ifax.com +1.215.438.4638 ext 8106 office +1.215.243.8335 fax ----- Original Message ----- From: "Darren Nickerson" <darren.nickerson@ifax.com> To: <asterisk-users@lists.digium.com> Sent: Friday, April 16, 2004 1:29 AM Subject: [Asterisk-Users] TE405P + Adit 600 and FXO module - should this work?> Folks, > > I'm experimenting with bringing multiple (8) analog lines from our local > telco into a Carrier Access ADIT 600 channel bank with an FXO module, then > having this talk to Asterisk via the T1 TDM controller on the ADIT and a > TE405P card. > > I don't know if this will work well (ie: give me decent echo cancellation, > call disconnect supervision, caller ID etc) but I haven't had much luck > getting this combination flying at all thus far. Should it work? > > I've been concentrating on the Adit T1 interface <----> TE405P connection > ... and have the following in zapata.conf: > > span=1,1,0,esf,b8zs > fxsks=1-24 > loadzone = us > defaultzone=us > > At the end of my zaptel.conf, I have: > > signalling=fxs_ks > group=2 > callerid="Joe Schmoe" <(215) 555-1212> > channel => 1-24 > > To get things flying, I do: > > modprobe zaptel > modprobe wct4xxp > > which causes the TE405P card to activate, but show a single flashing red > alarm on the configured span. > > The Adit's TDM controller also displays a solid red LED. Here's itsstatus:> > Adit 600> status a:1 > SLOT A: > Status for DS1 1: > Receive: Loss of Signal > Transmit: RAI/Yellow Alarm > Loopback: OFF > > Adit 600> > > I'm not sure I have the DS1 configured appropriately. It says: > > Adit 600> show a:1 > SLOT A: > Settings for DS1 1: > Circuit ID: CAC DS1# A:1 > Up/Down: UP > Framing: ESF > Line Coding: B8ZS > Line Build Out: DSX-1 EQUALIZATION FOR 0-133 ft. (CSU 0dB) > Loop Code Detection: ON > Loopback: OFF > FDL Type: None > > Can anyone familiar with the Adit 600 and/or TE405P see any obvious errors > here? > > -Darren > > -- > Darren Nickerson > Senior Sales & Support Engineer > iFAX Solutions, Inc. www.ifax.com > darren.nickerson@ifax.com > +1.215.438.4638 ext 8106 office > +1.215.243.8335 fax > > _______________________________________________ > Asterisk-Users mailing list > Asterisk-Users@lists.digium.com > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users >