Rahul Arvind Jadhav
2003-Sep-25 07:06 UTC
[Asterisk-Users] configuring TE410P for four E1 PRI lines
hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'. This is obviously because Quad T1 has only 96 channels. The question is how do i get the zaptel module to recognize the card as Quad E1 and not Quad T1. My current /etc/zaptel.conf goes as follows: ----------------------- span=1,0,0,ccs,hdb3,crc4 span=2,0,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 bchan=32-46,48-62 dchan=47 bchan=63-77,79-93 dchan=78 bchan=94-108,110-124 dchan=109 loadzone = us defaultzone = us ----------EOF------- Thanks, Rahul -- Rahul Arvind Jadhav Sr. Software Engineer (VoIP) NetYantra India Pvt. Ltd --------------------------
Richard Smith
2003-Sep-25 07:30 UTC
[Asterisk-Users] configuring TE410P for four E1 PRI lines
Rahul Arvind Jadhav wrote:> hi, > I'm trying to configure my newly acquired TE410P card to work as 4 E1 > spans. This is > supposed to be a drop-in replacement to the earlier E100P card. However, > on loading the > zaptel module it gets configured as T1 spans basically doing a 'cat' on > /proc/zaptel/1 thru 4, > it shows 24 channels per span. After this ztcfg fails saying > 'ZT_CHANCONFIG failed for channel 97'. > This is obviously because Quad T1 has only 96 channels. The question is > how do i get the zaptel module > to recognize the card as Quad E1 and not Quad T1. > My current /etc/zaptel.conf goes as follows: >There's jumpers on the board that are clearly marked. Jumper on = E1 Jumper Off = T1 Hope this helps.. -- Richard
Alastair Maw
2003-Sep-25 07:36 UTC
[Asterisk-Users] configuring TE410P for four E1 PRI lines
Rahul Arvind Jadhav wrote:> This is obviously because Quad T1 has only 96 channels. The question is > how do i get the zaptel module to recognize the card as Quad E1 and not Quad T1.You have to change the jumpers on the card. There are four in the middle of the card. Your zaptel.conf looks good, by the way. -- Alastair Maw MX Telecom - Systems Analyst http://www.mxtelecom.com
Leo Ann Boon
2003-Sep-25 16:28 UTC
[Asterisk-Users] configuring TE410P for four E1 PRI lines
Rahul Arvind Jadhav wrote:> hi, > I'm trying to configure my newly acquired TE410P card to work as 4 > E1 spans. This is > supposed to be a drop-in replacement to the earlier E100P card. > However, on loading the > zaptel module it gets configured as T1 spans basically doing a 'cat' > on /proc/zaptel/1 thru 4, > it shows 24 channels per span. After this ztcfg fails saying > 'ZT_CHANCONFIG failed for channel 97'. > This is obviously because Quad T1 has only 96 channels. The question > is how do i get the zaptel module > to recognize the card as Quad E1 and not Quad T1. > My current /etc/zaptel.conf goes as follows: > > ----------------------- > > span=1,0,0,ccs,hdb3,crc4 > span=2,0,0,ccs,hdb3,crc4 > span=3,0,0,ccs,hdb3,crc4 > span=4,0,0,ccs,hdb3,crc4 > > bchan=1-15,17-31 > dchan=16 > bchan=32-46,48-62 > dchan=47 > bchan=63-77,79-93 > dchan=78 > bchan=94-108,110-124 > dchan=109 > > loadzone = us > defaultzone = us > > ----------EOF------- > > Thanks, > RahulYou need to set the jumpers on the card.