Hi-
Just a couple of things to check:
I assume that the LED's blink RED when you first power up, meaning that
the board is basically alive.
Since you're E1, just checking that you've installed the 4 required
jumpers on the card for E1
It's possible you need a crossover cable instead of straight through:
1 <--> 4
2 <--> 5
4 <--> 1
5 <--> 2
You can cut up a CAT5 cable to make a cross over, but note that this
wiring is not the same as a CAT5 crossover.
Once you make this cable, you can also use it to connect channels to
each other on the card to get green lights (if your software is set up
correctly). This allows you to see if the problem is outside or inside
the system.
Good luck!
Scott Stingel
www.evtmedia.com
Ciro La Ferrara wrote:
> Hi,
> I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy
> come in on a pair of RG-59 coax cables with BNC connectors. So I need
> an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It
> but I am not sure that It works. I have configured my asterisk in this
> way:
>
> zaptel.conf
> span=1,1,0,ccs,hdb3,crc4
> dchan=16
> bchan=1-15,17-31
> loadzone=it
> defaultzone=it
>
> zapata.conf
> switchtype = EuroISDN
> signalling = pri_cpe
> pridialplan = unknown
> context = incoming
> group = 2
> channel => 1-15,17-31
>
> lsmod
> wct4xxp 51680 31
> zaptel 175904 64 [wct4xxp]
>
> ztcfg -vv
> Zaptel Configuration
> =====================>
> SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>
> Channel map:
>
> Channel 01: Individual Clear channel (Default) (Slaves: 01)
> Channel 02: Individual Clear channel (Default) (Slaves: 02)
> Channel 03: Individual Clear channel (Default) (Slaves: 03)
> Channel 04: Individual Clear channel (Default) (Slaves: 04)
> Channel 05: Individual Clear channel (Default) (Slaves: 05)
> Channel 06: Individual Clear channel (Default) (Slaves: 06)
> Channel 07: Individual Clear channel (Default) (Slaves: 07)
> Channel 08: Individual Clear channel (Default) (Slaves: 08)
> Channel 09: Individual Clear channel (Default) (Slaves: 09)
> Channel 10: Individual Clear channel (Default) (Slaves: 10)
> Channel 11: Individual Clear channel (Default) (Slaves: 11)
> Channel 12: Individual Clear channel (Default) (Slaves: 12)
> Channel 13: Individual Clear channel (Default) (Slaves: 13)
> Channel 14: Individual Clear channel (Default) (Slaves: 14)
> Channel 15: Individual Clear channel (Default) (Slaves: 15)
> Channel 16: D-channel (Default) (Slaves: 16)
> Channel 17: Individual Clear channel (Default) (Slaves: 17)
> Channel 18: Individual Clear channel (Default) (Slaves: 18)
> Channel 19: Individual Clear channel (Default) (Slaves: 19)
> Channel 20: Individual Clear channel (Default) (Slaves: 20)
> Channel 21: Individual Clear channel (Default) (Slaves: 21)
> Channel 22: Individual Clear channel (Default) (Slaves: 22)
> Channel 23: Individual Clear channel (Default) (Slaves: 23)
> Channel 24: Individual Clear channel (Default) (Slaves: 24)
> Channel 25: Individual Clear channel (Default) (Slaves: 25)
> Channel 26: Individual Clear channel (Default) (Slaves: 26)
> Channel 27: Individual Clear channel (Default) (Slaves: 27)
> Channel 28: Individual Clear channel (Default) (Slaves: 28)
> Channel 29: Individual Clear channel (Default) (Slaves: 29)
> Channel 30: Individual Clear channel (Default) (Slaves: 30)
> Channel 31: Individual Clear channel (Default) (Slaves: 31)
>
> 31 channels configured.
>
>
> With cable plugged in, the led are turned off.
> What's wrong?
>
> Ciro La Ferrara
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users@lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
> .
>