similar to: Trying to install X100P

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

Hi, I have already installed the X100P drivers but when I make to make call call, I always get No channel type registered for 'Zap'. Any idea how to solve this problem? It seems that the Zap module is not loaded but I have already load the driver by modprobe zaptel > modprobe wcfxo > ztcfg -vv thanks -------------- next part -------------- An HTML

I have just purchased a 2nd hand X100P, if I do a ztcfg -vv I get: "Zaptel Version: 1.4.0 Echo Canceller: MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured." My understanding of the above is that the zaptel driver has detected the card. What do I now need to do, in order to get an incoming call to work with

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I was studying the asterisk-users list archives to learn if anyone has had success with an X100P on a sparc. I noticed some postings on the subject. I am wondering if anyone has learned anything new? I have an Ultra-60 running Gentoo with 2.6.10 and udev. I built * 1.0.5 and have been enjoying various SIP configurations, with 2 sipura phones and 2 UIP200 phones (got them working!) in my home,

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hi Folks, Prior to upgrading my Zaptel sources everything was working fine. I have a X100P connected to my analogue line. The handset port of the X100P is connected to my desk phone's line 2 input. When the analogue line rings I see the CID on my line 2 but not from Asterisk on line 1 via the Cicso ATA. This used to work fine until I upgraded the sources. I get this when watching the

Hey all, ? I'm trying to get an E400P and 2 X100Ps working together in the one box and don't seem to be having much luck. ? I can get the two different types of boards working separately, but not together.? I've made calls on both the X100P and have seen sync and correct signalling on the E400P.? But when I try to enable to configs together I get the following: ? modprobe wcfxo

I've just installed a Digitnetworks X100P clone in my * server and run the install script for the voicepet-single-x100p tarball. The install appeared to run OK with modprobe wcfxo successful and the ztcfg reporting "Channel 01: FXS Kewlstart (Default) (Slaves: 01)". When I try to start * though I get a segmentation fault after loading res_features.so. I discovered that the

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a

Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o

PROBLEM: My x100p only does bad things. When I plug the line from the wall into the card, other phones in my house go nuts, no dialtone, crazy clicking, random tones, etc. Following the steps below, the line is screwed up any time I test after step 2. Just plugging the line from the wall into the x100p takes my other phones off line. External calls to my line hear busy. Obviously, can't

This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W

Tengo en una maquia ubuntu 8.10 el kernel es Linux 2.6.27-14-generic Quiero configurar una tarjeta x100p i usarla con asterisk, asi que descague compile e instale lo siguiente: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 Sin embargo no logro configurar la tarjeta con exito, ya probe casi? todo. Esto aparece si ejecuto lspci: 04:06.0 Communication controller: Motorola

Hi List, Could some kind soul post me a quick config that makes use of a Wildcat X100P when I do a show channels nothing is there lsmod shows the wcfxo and related drivers loaded and with no errors zap show channels is blank as well mucho thanks

Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, perhaps I can grepfor it and send you a smaller version. I have attached these as a tar ball to get below the 40K limit at which moderator approval is required. Thanks for the help. > Date: Fri, 7 Sep 2007 10:26:11

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

You should see something like this.... (I have 8 channels) tuxpbx*CLI> zap show channels Chan Extension Context Language MusicOnHold pseudo incoming en 1 incoming en 2 incoming en 3 incoming en 4 incoming en 5 incoming en 6

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or