Wiley E. Siler
2004-Oct-05 02:13 UTC
[Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap'
This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W -----Original Message----- From: khoonking [mailto:khoonkingsg@yahoo.com.sg] Sent: Tuesday, October 05, 2004 1:53 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap' Hi, This is what I have when I run ztcfg [root]# modprobe zaptel [root]# modprobe wcfxo [root]# ztcfg -vv Zaptel Configuration ===================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured.>Basically you need to look through the startup messages till you come >up with the proper error message concerning why it isn't accepting the >zap definition.I don't see any error message when I run asterisk -vvvvgc. Ussually, it will print parsing of extensions.conf, sip.conf and etc. Does it parse the file zapata.conf? -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, October 05, 2004 3:39 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegistered for 'Zap' On Tue, 2004-10-05 at 02:15, khoonking wrote:> Hi, > > I have confirmed that there is no space between "=>" but still the > same problem. > > > zapatel.conf > > =======================> > [channels] > > signalling=fxs_ks > > context=incoming > channel => 1 ;X100P > > >[incoming] > >;exten => s,1,Echo ;for testing the connection > >exten => s,1,Answer ; Answer the line > >exten => s,2,Playback,demo-thanks ;for playing a file > > > [default] > > exten => 6200,1,Dial(SIP/6200,20) > > exten => 6203,1,Dial(SIP/6203,20) > > exten => _X.,1,Dial,Zap/1/${EXTEN} > > When I call from an analog phone to the X100P ext, Asterisk CLI screen> does not print anything.if asterisk doesn't know about the port yet, it can't detect the signal nor answer the line. Basically you need to look through the startup messages till you come up with the proper error message concerning why it isn't accepting the zap definition. -- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer
khoonking
2004-Oct-05 02:32 UTC
[Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor'Zap'
>If you run ZAP SHOW CHANNELS from the CLI what do you see?No such command Best Regards Meng Kim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Wiley E. Siler Sent: Tuesday, October 05, 2004 5:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor'Zap' This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W -----Original Message----- From: khoonking [mailto:khoonkingsg@yahoo.com.sg] Sent: Tuesday, October 05, 2004 1:53 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap' Hi, This is what I have when I run ztcfg [root]# modprobe zaptel [root]# modprobe wcfxo [root]# ztcfg -vv Zaptel Configuration ===================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured.>Basically you need to look through the startup messages till you come >up with the proper error message concerning why it isn't accepting the >zap definition.I don't see any error message when I run asterisk -vvvvgc. Ussually, it will print parsing of extensions.conf, sip.conf and etc. Does it parse the file zapata.conf? -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, October 05, 2004 3:39 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegistered for 'Zap' On Tue, 2004-10-05 at 02:15, khoonking wrote:> Hi, > > I have confirmed that there is no space between "=>" but still the > same problem. > > > zapatel.conf > > =======================> > [channels] > > signalling=fxs_ks > > context=incoming > channel => 1 ;X100P > > >[incoming] > >;exten => s,1,Echo ;for testing the connection > >exten => s,1,Answer ; Answer the line > >exten => s,2,Playback,demo-thanks ;for playing a file > > > [default] > > exten => 6200,1,Dial(SIP/6200,20) > > exten => 6203,1,Dial(SIP/6203,20) > > exten => _X.,1,Dial,Zap/1/${EXTEN} > > When I call from an analog phone to the X100P ext, Asterisk CLI screen> does not print anything.if asterisk doesn't know about the port yet, it can't detect the signal nor answer the line. Basically you need to look through the startup messages till you come up with the proper error message concerning why it isn't accepting the zap definition. -- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
khoonking
2004-Oct-05 02:34 UTC
[Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor'Zap'
>If you run ZAP SHOW CHANNELS from the CLI what do you see?No such command Did I miss out anything? Best Regards Meng Kim -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Wiley E. Siler Sent: Tuesday, October 05, 2004 5:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor'Zap' This may seem obvious or silly but have you tried using a different phone cord? A bad phone cord played havoc on a colleague of mine during initial config. Fro what you show as your output from ztcfg, you should have one channel configured successfully then. Your example shows you have the channel set to one so no problem there. If you run ZAP SHOW CHANNELS from the CLI what do you see? W -----Original Message----- From: khoonking [mailto:khoonkingsg@yahoo.com.sg] Sent: Tuesday, October 05, 2004 1:53 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegisteredfor 'Zap' Hi, This is what I have when I run ztcfg [root]# modprobe zaptel [root]# modprobe wcfxo [root]# ztcfg -vv Zaptel Configuration ===================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured.>Basically you need to look through the startup messages till you come >up with the proper error message concerning why it isn't accepting the >zap definition.I don't see any error message when I run asterisk -vvvvgc. Ussually, it will print parsing of extensions.conf, sip.conf and etc. Does it parse the file zapata.conf? -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Steven Critchfield Sent: Tuesday, October 05, 2004 3:39 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: RE: [Asterisk-Users] problems with X100P - Nochanneltyperegistered for 'Zap' On Tue, 2004-10-05 at 02:15, khoonking wrote:> Hi, > > I have confirmed that there is no space between "=>" but still the > same problem. > > > zapatel.conf > > =======================> > [channels] > > signalling=fxs_ks > > context=incoming > channel => 1 ;X100P > > >[incoming] > >;exten => s,1,Echo ;for testing the connection > >exten => s,1,Answer ; Answer the line > >exten => s,2,Playback,demo-thanks ;for playing a file > > > [default] > > exten => 6200,1,Dial(SIP/6200,20) > > exten => 6203,1,Dial(SIP/6203,20) > > exten => _X.,1,Dial,Zap/1/${EXTEN} > > When I call from an analog phone to the X100P ext, Asterisk CLI screen> does not print anything.if asterisk doesn't know about the port yet, it can't detect the signal nor answer the line. Basically you need to look through the startup messages till you come up with the proper error message concerning why it isn't accepting the zap definition. -- Steven Critchfield <critch@basesys.com> _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the sender and delete the material from any computer _______________________________________________ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Reasonably Related Threads
- problems with X100P -Nochanneltyperegisteredfor'Zap'
- problems withX100P-Nochanneltyperegisteredfor'Zap'
- problems with X100P - No channeltyperegisteredfor 'Zap'
- problems with X100P - No channel type registered for 'Zap'
- cli command to check the codec use for the connected calls