similar to: Adit 600 as VoIP router (MGCP) and Asterisk

Has anyone had any success using the Adit 600 with the CMG card talking MGCP to asterisk? I want to have a central asterisk server with 10 Adit 600's at various locations providing 24 FXS ports.... Thanks, Isaac

I've finally got my Adit 600 and are configuring it right now. But I have to say, there aren't much documentation for it. I've setup MGCP and Asterisk seems to find it. But all channels (40 FXS channels) are "Down"! But the MGCP itself is "Up" according to the statistics. I can't find any documents how to set each channel to "Up" in the CLI. Any

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Does anyone know what I need to put in the mgcp.conf to connect to an adit 600? Also if you know what I need to configure on the Adit600 itself, that would help too. - --Tod -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.1 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

According to CarrierAccess, the Adit 600 uses CAS for voice signalling. What is this? This should not be a problem for Asterisk? Does the Asterisk server need to reencode CAS into aLaw when going to Euro ISDN? BR Daniel Nystr?m

I am trying to find a manual for the Carrier Access Adit 600. Does anyone know where I might be able to find one? Thanks -Jon -- Jon J. Brandon jon@monsoonretail.com http://www.monsoonretail.com

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and

Do anyone knows abount European resellers of these products: * Digium Wildcard TE410P * CarrierAccess Adit 600 Preferably in Sweden, but Europe is also better. Have anyone within EU ordered products from these companies directly from the US? In that case, how is the service and delivery? Thanks, folks!

I've searched but can't find an answer as to how many MGCP paths can a single ADIT/CMG card support? It appears it's only 24 ports, maybe 48. What I'd like to do is install 6 Telco T1's into a single (or more) Adit 600 and route inbound calls towards asterisk. Can I have more than one CMG in a single chassis? Or maybe you know of a better way to connect T1's to

Hi, Anybody out there running Adit600s? I have in my care an Adit600 channel bank connected to an old (version 1.0.6) Asterisk instance with MGCP. When trying a more recent Asterisk (1.4.21.2~dfsg-3+lenny1, Stock current Debian) calls fail. I have attempted to add the "slowsequence = yes" line to mgcp.conf. (It seemed to be the only likely candidate in the example files I found

I am forklifting a Merridian option 51c with 112 Nortel Digital Handsets and 400 analog units. For the analog units I have quotes for 9 ADIT 600 48 port fxs units and 17 Rhino 24 port FXS channel banks. I have used neither. Which is the best choice? The price difference is not that great. I am looking at Citelinks 24 port Handset Gateway for the Nortel Digital units. (Any other suggestions

I'm emailing this as the customer in this case, since my carrier appears to be completely unable to solve this. A brief rundown of the problem: - We have several voice lines going through the ADIT, of course into a VoIP type of arrangement. - Voice traffic will become choppy, even drop calls completely, at random but quite often. Modem calls (which we needed unfortunately) are a joke. -

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Hi again folks! ;) As before, I will transform one E1 30 Channel PRI into 30 FXS channels using Adit 600. Now I'm into choosing server platform. And the two opponents are: * Dell PowerEdge 750 w/ SCSI RAID (or even SATA RAID1) * FujistuSiemens PRIMERGY RX100 S2 (SATA RAID1) As I've seen people having problem with HP server, I havn't looked at it at all. What experience do you

Hi All, I'm trying to hook up asterisk (CVS-HEAD-02/09/05-13:44:11 ) to a ADIT 600 via MGCP. Got it working really nice but now have a pretty bad problem: 1. When I perform a flash on the telephone, I usually get a second dialtone, but when I dial, dialtone doesn't break. If I flash back and forth a few times, it will eventually give me no dialtone.. here if I dial, it successfully

What server hardware would you recommend for an Asterisk system which are really critical? The additional hardware will probably be two digium TE110P cards, and an Adit 600 platform. If it's possible to run on -48VDC, It would be great! Are there any experiences with any HP or FujitsuSiemens systems? Or other "complete server" systems? Thanks! BR Daniel Nystr?m

I have this idea to use an old ADIT 600 with a CMG card to convert two T1 TDM circuits to MGCP towards asterisk. The basics I've found on the net, but there is not much available. I've cut and pasted the mgcp.conf details I could find, but there not much as far as CMG setup. I was hoping I could hook-up with someone that's tried this so I could pick your brain about the finer

A little off-topic maybe, but it's still for the Adit used with Asterisk. ;) I wonder where I can buy 50 pin Amphenol cables, with connector on one side, and open cables on the other for mounting in our own patch panels. In Europe, or Sweden preferably. It's said to be very common on telcos, but I can't find it for sale anywhere! Thanks!

I have an adit 600 with an fxo card connected to a digium T1 card. If I try to make an outgoing call and the T1 cable is disconnected, asterisks returns congested like it should. But, if the adit 600 is connected to the T1 card, the adit 600 immediately "answers" the call even if there are no physical lines attached. I even removed the fxo card and the adit 600 still

Ok, I've pretty much decided to try the Adit route. Somebody who has experience with these tell me if I'm missing something. I have 15 incoming PSTN lines. T1 is not an option at current location. I want to put in an Adit 600 with 2 8-port FXO boards. The adit will then connect to * via a digium t1 board. I configure zaptel.conf for the T1. What other parts would be needed? How do

Folks, I'm experimenting with bringing multiple (8) analog lines from our local telco into a Carrier Access ADIT 600 channel bank with an FXO module, then having this talk to Asterisk via the T1 TDM controller on the ADIT and a TE405P card. I don't know if this will work well (ie: give me decent echo cancellation, call disconnect supervision, caller ID etc) but I haven't had much