similar to: TE410P PRI problems

hi all, i am trying to get my TE410P (see previous posts) working in Austria (telekom Austria - i am still waiting for an answer for my questions). my /etc/zaptel.conf looks like -------------------------------- span=1,1,0,ccs,hdb3,crc4,yellow span=2,2,0,ccs,hdb3,crc4,yellow bchan=1-15,17-31 dchan=16 bchan=32-46,48-62 dchan=47 loadzone=at defaultzone=at -------------------------------- after

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

I have a TE405/TE410P card that was working on 1.0.X I upgraded the OS to Centos 4.5, Updated asterisk to 1.4 and zaptel to 1.4.5 and libpri. I copied all the zaptel and zapata and extensions.conf files from 1.0 I did update extensions.conf from 1.0 to 1.4 commands. I cannot get the card to work in 1.4.10. AHHH! I see with zttool that the T1 is in Green, I see calls coming in as the bits go

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040810/16371a21/attachment.htm -------------- next part -------------- ? Hi, I'm using TE410P card with four T1 lines. I've configured all the channels in my /etc/zaptel.conf file. In zttool i'm getting "OK" for the "Span-1" but the other three spans giving

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

I've been running Asterisk for months with no problems. I have grown to the point where I need an aditional TE cards. After many attempts I was able to add the second card without affecting the performance of the first. However, the second card is not working properly. Setup ===== - Running on a Dell Server. - RedHat 8 - Asterisk 1.0 - I have two TE410Ps on that box, card 0 assigned to

Hi all I'm trying to configure a TE410P in Europe with three E1s and a T1 channel bank (already bought in the US) to receive and make calls through *. I managed to get the E1s to work, but I'm having trouble with the channel bank (a Rhino). I have tried the bank in spans 1 and 4 changing jumpers in the card (always with no PRI connected, as I have no PRI where I'm testing now,

Hi all, I'm diagnosing a problem related to PRI card. I would like to know the following: assuming I've got a working PRI card and correctly installed Linux drivers and a PRI line connected to the card, even without starting asterisk, shouldn't I hear a ring tone when I dial the number? I'm getting busy tone all the time. I'm thinking the patch cable I made may be causing

Hello all, I'm using Wildcard TE410P card. Here is a zaptel.cfg loadzone=se defaultzone=se span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 span=2,0,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-62 span=3,0,0,ccs,hdb3,crc4 bchan=63-77 dchan=78 bchan=79-93 span=4,0,0,ccs,hdb3,crc4 bchan=94-108 dchan=109 bchan=110-124 # ztcfg -vvv Zaptel Configuration ====================== SPAN 1:

hi all, i am getting crazy with my TE410P - it won't work now we already think that the only thing which can be wrong is the cable. At our telecom endpoint we have 1-2 tx, 4-5 rx So - which cable do i need to get it working Already tried a cross over cable 1-2 -> 4-5 / 4-5 -> 1-2 (with this cable nothing works -> red alarm on both ends) Also a normal cable 1-2 -> 1-2 / 4-5 ->

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

I'm trying to connect an Asterisk T1 port to a Dialogic card. The Dialogic side is an external VMS. I setup for ISDN-PRI between systems and have green lights on both card/ports. Zttool shows connection is good also. However, when I try attempt terminate or originate a call to either system, nothing appears of CLI. How can I monitor the "D" channel? zaptel.conf: # Span 8:

I just installed a TE410P on a Debian Sarge system running kernel 2.6.11-1-686-smp. Zaptel and Asterisk seem to be working fine. However, I have a couple of problems with the TE410P and Zaptel. First, the TE410P is showing me red alarms on 2 of the 4 T1s. This board (the TE410P) was just moved from another machine running REL3 and all 4 T1s were working there. I don't know why only

Hi everyone! Here is my configuration and messages taken from Asterisk startup. The E1 PRI trunk is connected to our national telecom company here in Croatia. When I call from outside over this trunk to my company I get 'error in connection' respnse. In the same moment I can't see anything in Asterisk, nothing that will tell me that the call reached Asterisk. I think there is a

Hi everybody I've just installed a new Redhat 8.0 and configured it with Asterisk, zaptel and libpri. Afterwards I installed a TE410P and configured this as well. But when starting Asterisk I get the following error message: ------------------------------------------------------- -- Registered channel 1, PRI Signalling signalling ..... -- Registered channel 15, PRI Signalling