asterisk users - Jan 2005 - TE410P problem (Looping UP Span 1...)

Hi list,
 
We have been trying to configure a Quad Span T1 card in a system running RH9. We
have followed the instructions in the Wiki and searched the mailing lists, but
so far havent got any success. Cable is connected to the first span, and module
is loaded. Without loading the module the LED glows in red colour, but the
moment we load module, it goes off. (No red or green) .
 
We ran zttool and tried to run a loop test, but zttool simply hung with the
message 'Looping UP Span 1...'. We had to terminate zttool with
'kill'.  Here is the output of the lsmod command. Can someone shed some
light on this?
 
Thanks,
-Sid
 
Module                  Size  Used by    Not tainted
wcusb                  20128   0  (unused)
wct4xxp                54272   0  (unused)
zaptel                182432   0  [wcusb wct4xxp]
 
tail -f /var/log/messages
Jan  6 14:54:32 localhost kernel: TE410P: Launching card: 0
Jan  6 14:54:32 localhost kernel: TE410P: Setting up global serial parameters
Jan  6 14:54:32 localhost kernel: Found a Wildcard: Wildcard TE410P-Xilinx
Jan  6 14:54:32 localhost kernel: usb.c: registered new driver wcusb
Jan  6 14:54:32 localhost kernel: Wildcard USB FXS Interface driver registered
Jan  6 14:54:33 localhost kernel: Registered tone zone 0 (United States / North
America)
Jan  6 14:54:33 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
Jan  6 14:54:33 localhost zaptel: Running ztcfg:  succeeded
Jan  6 14:55:07 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
Jan  6 14:55:07 localhost kernel: Registered tone zone 0 (United States / North
America)
 

		
---------------------------------
Do you Yahoo!?
 Yahoo! Mail - Helps protect you from nasty viruses.
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20050106/8ae20f5e/attachment.htm

Sid-

Try connecting one port to another.  Note that one of the ports must be 
set up as "cpe" and the other as "net" in zapata.conf when
you loop them
together like this.

A suitable crossover cable for testing can be constructed by cutting up 
a CAT 5 cable, and connecting:
Pin 1 <--> Pin 4 on the other end
Pin 2 <--> Pin 5
Pin 4 <--> Pin 1
Pin 5 <--> Pin 2

You should get green's on both the connected channels if your zaptel and 
zapata configurations are ok, and if you've run both modprobe and ztcfg 
as documented.

Good luck
Scott Stingel
President
EVT, Inc.

www.evtmedia.com



Sid wrote:
> Hi list,
>  
> We have been trying to configure a Quad Span T1 card in a system 
> running RH9. We have followed the instructions in the Wiki and 
> searched the mailing lists, but so far havent got any success. Cable 
> is connected to the first span, and module is loaded. Without loading 
> the module the LED glows in red colour, but the moment we load module, 
> it goes off. (No red or green) .
>  
> We ran zttool and tried to run a loop test, but zttool simply hung 
> with the message 'Looping UP Span 1...'. We had to terminate zttool
> with 'kill'.  Here is the output of the lsmod command. Can someone 
> shed some light on this?
>  
> Thanks,
> -Sid
>  
> Module                  Size  Used by    Not tainted
> wcusb                  20128   0  (unused)
> wct4xxp                54272   0  (unused)
> zaptel                182432   0  [wcusb wct4xxp]
>  
> tail -f /var/log/messages
> Jan  6 14:54:32 localhost kernel: TE410P: Launching card: 0
> Jan  6 14:54:32 localhost kernel: TE410P: Setting up global serial 
> parameters
> Jan  6 14:54:32 localhost kernel: Found a Wildcard: Wildcard TE410P-Xilinx
> Jan  6 14:54:32 localhost kernel: usb.c: registered new driver wcusb
> Jan  6 14:54:32 localhost kernel: Wildcard USB FXS Interface driver 
> registered
> Jan  6 14:54:33 localhost kernel: Registered tone zone 0 (United 
> States / North America)
> Jan  6 14:54:33 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
> Jan  6 14:54:33 localhost zaptel: Running ztcfg:  succeeded
> Jan  6 14:55:07 localhost kernel: TE410P: Span 1 configured for ESF/B8ZS
> Jan  6 14:55:07 localhost kernel: Registered tone zone 0 (United 
> States / North America)
>  
>
> ------------------------------------------------------------------------
> Do you Yahoo!?
> Yahoo! Mail 
>
<http://us.rd.yahoo.com/mail_us/taglines/virus/*http://promotions.yahoo.com/new_mail/static/protection.html>
> - Helps protect you from nasty viruses.
>
>------------------------------------------------------------------------
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users@lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>