Displaying 20 results from an estimated 7000 matches similar to: "No B-Channels. PRI. E100P. HELP!"
2007 Jun 28
2
E1 not coming up
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello List,
since some days i run into the problem that one span on a TE407P is not
comming up correctly. With intense debug on that span i get:
< [ 02 01 7f ]
< Unnumbered frame:
< SAPI: 00 C/R: 1 EA: 0
< TEI: 000 EA: 1
< M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode
extended) ]
< 0 bytes of data
2004 Sep 03
5
Digium E100P and PMX in Germany
Hello ml,
i need some help on my zaptel configuration. My E100P only shows some
YELLOW / RED alarm when I load the wct1xxp module and do a
cat /proc/zaptel/1
Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED
...
..
.
My /etc/zaptel.conf is:
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16
loadzone=nl
defaultzone=nl
I tried zaptel-1.0RC2 and the latest CVS
2008 May 04
1
UK BT ISDN30e PRI Problem
Ok Guys, I've done a tonne of hunting around on this problem, but
can't find much help.
I'm running:
asterisk 1.4.19.1
libpri 1.4.3
and zaptel 1.4.9.2 which I believe has been modified by RedFone to add
the ztd-ethmf module.
My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a
BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic
PBX on span 4. Upon
2004 Jul 17
4
E100P and Colt Telecom (Europe)
Hi,
Has anyone connected * to a Colt E1 line in Europe? If
so could you send me the zaptel.conf and zapata.conf.
Thanks,
Aaron
__________________________________
Do you Yahoo!?
New and Improved Yahoo! Mail - Send 10MB messages!
http://promotions.yahoo.com/new_mail
2003 Jul 11
7
ISDN PRI E1 configuration with E100P
<P>hi Everyone,</P>
<P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P>
<P>*CLI> <BR> == D-Channel on span 1 up<BR> -- B-channel 1 successfully restarted on span 1<BR> --
2003 Oct 09
2
E100P setup in Switzerland
Hi all,
I am trying to setup an E100P for use on Swisscom E1-PRI here in
Switzerland.
Swisscom seems to use Siemens hardware.
Here are my configs (cvs from a few hours ago) :
zaptel.conf
loadzone=fr ; tried "de" but got warning at modprobe
defaultzone=fr
span=1,1,0,cas,hdb3,crc4,yellow ; Seems to be right, as the Siemens
SDSL-G703 modem switches its LEDs off ... not sure
2004 Jan 04
2
Two E100P boards - could not load zaptel module - Channel 63 - no such device
Hi,
I have two E100P boards connected to my PC. I wish to setup two
E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one
with 30 channels. When I try to load zaptel modules, I get an error message:
"Loading zaptel framework:
Loading zaptel hardware modules: wct1xxp wcusb
Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device"
Follows my zaptel.conf:
2004 Jun 12
2
Sending SABME continuosly. Urgent help needed!
Hi, I'm trying to install an E1 PRI, and I need it working by
Monday, but although everything seems ok, I get no response to calls.
When I make a pri extense debug on span 1, I repeatedly get the
following:
Sending Set Asynchronous Balanced Mode Extended
[ 00 01 7f ]
Unnumbered frame:
SAPI: 00 C/R: 0 EA: 0
TEI: 999 EA: 1
M3: 3
2004 Nov 23
1
Error when install E100P
Hi, all
I am trying to install E100P card, the 'modprobe zaptel' is ok, but
when I did 'modprobe wct1xxp', I got such error, so can not load the
driver for the card.
/lib/modules/2.4.20-8/misc/wct1xxp.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters.
You may find more information in syslog
2004 Aug 04
4
Problems with E100P
Hi,
I'm having trouble configuring and E1 link , I know the E1 is a PRI
and the switchtype is 5ess. The problem is that everytime I try to dial
I got and error saying that it was unable to open the zap channel .
Devices are created in the /dev/zap directory and I can open them with a
cat /dev/zap/1. I can also see the channels in /proc/zaptel/1.
Thanks in advance
[zaptel.conf]
2005 Jun 15
2
Nasty little incident ...
We have a te410p, with the following connections:
span 1 connected to a 32 Channel EuroISDN
span 2 connected to a card in a legacy pbx (Meridian)
span 3 connected to a 10 Channel EuroISDN
span 4 connected to a card in a legacy pbx (Meridian)
We have no need for the meridian now, and decided to turn it off. I did
not change the zaptel.conf settings, nor the zapata.conf settings.
When the
2003 Sep 25
3
configuring TE410P for four E1 PRI lines
hi,
I'm trying to configure my newly acquired TE410P card to work as 4
E1 spans. This is
supposed to be a drop-in replacement to the earlier E100P card. However,
on loading the
zaptel module it gets configured as T1 spans basically doing a 'cat' on
/proc/zaptel/1 thru 4,
it shows 24 channels per span. After this ztcfg fails saying
'ZT_CHANCONFIG failed for channel 97'.
2004 Jun 01
1
E100P isdn pri installation
Hi,
I'm installing E100P for isdn pri line.
My configuration are like this.
zaptel.conf
=======================================
span=1,0,0,ccs,hdb3,crc4
loadzone = us
defaultzone=us
bchan=1-15
dchan=16
bchan=17-31
zapata.conf
=================================================
[channels]
context=default
switchtype=euroisdn
context=default
signalling=pri_net
usecallerid=yes
2004 Aug 12
5
Question about TE405P
Hi all,
Does somebody know how I have to setup my TE405P ?
Is it correct my configuration below ? Otherwise, can somebody help me ?
Thanks,
Angel.
zaptel.conf
span=1,1,0,ccs,hdb3
span=2,0,1,ccs,hdb3
span=3,0,1,ccs,hdb3
span=4,0,1,ccs,hdb3
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
bchan=1-15
dchan=16
bchan=17-31
2004 Apr 29
2
e100p installation
Hi, I buyed a wildcard e100p and I installed that but when I load asterisk I
have this error:
Apr 29 18:59:25 WARNING[8192]: chan_zap.c:690 zt_open: Unable to open
'/dev/zap/channel': No such device
Apr 29 18:59:25 ERROR[8192]: chan_zap.c:5403 mkintf: Unable to open channel
1: No such device
here = 0, tmp->channel = 1, channel = 1
Apr 29 18:59:25 ERROR[8192]: chan_zap.c:7526
2003 Jun 23
1
Setting up the E100P
Hello,
I have an E100P, and in the zaptel.conf I have:
span=1,1,0,ccs,hdb4,crc4,yellow
fxsks=1-10
the light on the card is green( BTW what do all those states of the card
that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or
for the card?)
in the asterisks` zapata.conf I have:
[channels]
context=default
switchtype=euroisdn
signalling=fxs_ks
usecallerid=yes
hidecallerid=no
2004 Dec 10
2
Asterisk 1.0.3 - Signaling on E100P.
Hello list ,
I?m putting to work a new asterisk box.
I?m running * 1.0.3 with (one )
Wildcard TDM ( 2FXS* 2FXO) and
(one) E-100P.
Both boards are working well. ztcfg
don?t show me any error.
zttool list both cards as "OK"
But when i run asterisk on verbose mode
i get those errors :
[chan_zap.so] => (Zapata Telephony)
== Parsing '/etc/asterisk/zapata.conf': Found
--
2006 Oct 16
1
ZapHFC & quadBRI D-Channel going down randomly
Hi.
I'm running some asterisk boxes on different sites,
some equipped with a couple of ZapHFC cards, others with
Junghanns quadBRI cards.
All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6)
and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with
kernel 2.6.17.3
The cards are connected to Telecom Italia's NT1/NT1+ S/T lines;
some of them are point-to-point,
2007 Aug 24
2
TE210P digim card PRI problem
Dear all
I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI
asterisk think PRI_CPE and remote end also CPE
i have configure /etc/zaptel.conf
span=1,1,0,ccs,hdb3
2004 Sep 16
2
Help with E1 configuration
Hi,
I currently have a E100P card installed on my machine and the E1
subscription will be activated pretty soon. However, I have no idea how to
configure asterisk to make inbound and outbound call using the E1.
Especially for extensions.conf. Below is the configuration I used for
zaptel.conf and zapata.conf. Is it possible if someone can verify if the
configuration for zaptel and zapata is