similar to: Asterisk's configuration : Which signalling in France with an E1 ?

All, I'd like to buy an E100P Wildcard frm Digium, but i prefer to buy it in Europe (costs, ...). Could somebody point me to an european reseller ? Thanks in advance. -- Nicolas Cartron nc@ncartron.org

Hello, Thanks to members of the list things changed on my installation (asterisk + digium E100P with of course an E1 line). Here is my zaptel.conf : - span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=fr defaultzone=fr - Output of zttool: - Alarms Span YEL/RED Digium Wildcard E100P E1/PRA Card 0 - [root@asterisk root]# head /proc/zaptel/1 Span 1: WCT1/0 "Digium

Hullo everyone, Iam new to Asterix but am trying to get R2 signalling working with a Digium E100P E1/PRA Card. My Telecom doesn't have an implementation of ISDN PRI yet, so it's R2 that is supported. Could anyone have a patch to fix this for me. Am told it has something to do with Assembly Language programming. Please help me fix this. Regards, Nicholas

Hola! I've a Digium E1 card, zaptel recognizes it as (loading the module with debug=1) Setting up DMA (write/read = 321b2000/321b2200) Controller version: 43 Framer: DS21554, Revision: 5 (E1) Found a Wildcard: Digium Wildcard E100P E1/PRA Using CCS/HDB3 coding/framing with CRC4 120 Ohms Calling startup (flags is 4099) Started DMA Got interrupt: 0x0005 /etc/zaptel.conf:

Hello, I have a little problem with signalling. An E100p is connected to an Alcatel PBX, wich has an E1 to the outside. Located in Germany. zapata.conf: switchtype=euroisdn pridialplan=local prilocaldialplan=local overlapdial=yes signalling=pri_cpe .... With asterisk 1.0.2 I can call from a SIP phone to a phone connected to the Alcatel and the SIP number is correctly displayed at the caller.

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi ! I am trying to configure two E100P cards, but I am a bit confused with zapta.conf in what I am trying to achieve. The * will be connected to a pstn switch with two E1 PRI lines. The E1 lines will be used for incoming calls as well as outgoing calls. My problem now is what to put in zapta.conf, I would like to group all channels from both cards together (if that's possible). Does this

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hey all! I had an experience trying to set up an E1 in Brazil which could help somebody. In Brazil is very common telcos to have just R2 digital as their primary signaling. As I were trying to set up an E100P, which does not support R2 yet, I had to test an other signaling which works perfectly with Asterisk. They call this signaling as RDSI, using ccs as framing and PA (primary access) as

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hi, I currently have a E100P card installed on my machine and the E1 subscription will be activated pretty soon. However, I have no idea how to configure asterisk to make inbound and outbound call using the E1. Especially for extensions.conf. Below is the configuration I used for zaptel.conf and zapata.conf. Is it possible if someone can verify if the configuration for zaptel and zapata is

Hi All, I've bought a R2Adapter to convert R2Digital to ISDN. I am trying to config E100P card but D-Channel is down. I know R2Adapter uses ETSI ISDN Protocol so I tried unsucessfully setup switchtype to EuroISDN. Any clue? Daniel

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

hi guys, I have a little problem maybe you can help ... I have an asterisk setup, with an E100P, and an ISDN-PRI 30 channel line from the telco going into it .. the E1 line is OK, because plugged into a Lucent Portmaster 4 it works OK .. plugged into the asterisk box I just get an engaged tone, and asterisk posts this message on screen : WARNING[1167272000]: File chan_zap.c, Line 5275

I've got a * box with a TDM40B and an E100P. The E1 is connected to a Shout900 VoIP gateway from net.com. My question is, when I place a call from an analog phone and that call is routed over the E1, what encoding is used? And do I have any control over that? I'm obviously not an expert here, but the Shout900 vendor is claiming that some difficulties that we are having with integration are

I've been beating my head a bit against the 1.0.6 Debian builds of Asterisk, using an E100P (E1, single span) board. In machines I've built in the past (back in 1.0.0 days), config I'm using and that card and 1.0.0 driver combo worked fine. ztcfg reports no problems: SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 31 channels configured. And zttool sees the card, and

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

We are not having any luck with the E100p card here in Australia, it will work with a crossover cable to another device but will not talk to our Telco Telstra who probably have a weird implementation of an E1. Any suggestions on a replacement? Regards Mark McKibbin DCS Internet 64 Queen St Warragul Victoria 3820 Australia www.dcsi.net.au mark@team.dcsi.net.au Ph. 1300 665575 Fx. 1300 556595

Hi all, I have got the following problem (E100P, pri_cpe): My number range is <6digits>xyz. (e.g. 123456-999)