search for: falce

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

I have a TE410P running on CentOS 4 which (fortunately) is my test system. This card has been working flawlessly for the past few weeks. Today I did a cvs update to the latest head files, and the card is now not working. When I try a zaptel start, a series of messages appears on the console: Found TE410p at base address fdff0000, remapped to f8a34000 TE410P version c01a010b, burst ON, slip

...issedCount":7,"Total":7}])") in new stack -- Executing [h at ext-queues:3] NoOp("SIP/100-00000050", "") in new stack -- Executing [h at ext-queues:4] Macro("SIP/100-00000050", "hangupcall,") in new st U can see that Execif = 0 = falce but somehow Shell ${SHELL(curl -X POST --header "Content-Type: application/json" --header "Accept: application/json" -d "{\"Phone\": ${FROMEXTEN}, \"Source\": \"asterisk\"}" " http://sIte.com:80/api/v1/calls?apiKey=UABVAEI&cli...

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

Hi All I have a TE110P card connected to a PRI line. In my zaptel.conf I have: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us and my zapata.conf is: [channels] context=inbound-pri switchtype = national pridialplan=unknown ;pridialplan=international signalling = pri_cpe callerid=asreceived busydetect=no usecallerid=yes hidecallerid=no callwaiting=no callwaitingcallerid=no

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi list, After a lot of testing + troubleshooting, I guess I'm observing what I am now calling a regression with zaptel 1.4.10 (is it?) As such I call for peer feedback, before either asking Digium install support or filing a bug. Thanks in advance! System: HP Proliant DL380 G5 with 2x PCI-X + 1x PCIe riser card OS: Centos 5 Kernel: 2.6.18-53.1.14.el5 (also tested under

Hello everyone. I have server with 2E1 PCI card, asterisk 1.4.35, dahdi 2.4.0, libpri 1.4.12-beta2. One PRI trunk looks to PSTN and take a clocksource from telco. Another trunk looks to PBX with DECT system. Some outgoing calls from asterisk to PSTN drops. The last message that exists before hanging up process is: DEBUG[28467] channel.c: Got a FRAME_CONTROL (8) frame on channel DAHDI/... This

Hi, I'm trying to get a TE212 working on a Dell PowerEdge 1850 running Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1) and asterisk (1.4.4). The initilization of the Octasic echo canceller seems to fail when the wct4xxp module is loaded. [...] VPM450: echo cancellation for 64 channels Failed to open chip, code 00103017! VPM450: Failed to initialize [...] By looking

Hello: Have a TE110P laying around and decided to see if I could build a router around it. I've tried compiling several versions of zaptel .1.4.x with the same results. I checked the zaptel changelog and can't find anything about it no longer being supported (or that it ever was for that matter). ztcfg: Zaptel Configuration SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

I've seen this consistently on three systems, with three different cards, and multiple versions of DAHDI. At first I thought the issue only occurred on newer, Nehalem-based, systems, but I reproduced it on a Core 2 Duo box as well. I've tested with dahdi-linux 2.2.0.2, dadhi- linux-complete 2.0.0+2.0.0, 2.1.0.2+2.1.0.2, and 2.2.0.2+2.2.0. The card is a Digium TE220B which uses the

Hi to all, I have a problem with this wildcard and one E1 line. The server is a Asus P4P800S with the 865PE chipset, and 512MB RAM. The kernel version is 2.4.26. I have donwload and build the latest CVS version of zaptel, libpri and asterisk following the ufficial instructions of digium. I have set up my server in this way: zaptel.conf loadzone=it defaultzone=it

Hi guys I'm Danilo Falc?o (fcon), a Sys Admin from Brazil and living in Germany. Recently I have joined Fedora QA & Infrastructure and now the CentOS project to work with Lokesh (lsm5) building RPMS for Docker and related packages. In the past years I've been working a lot with Virtualization (XEN and KVM mostly) and since Docker appeared I became a big fan of it. I'm also a