asterisk users - Apr 2007 - Problems with Digium TE110P

Hi everyone

I have a Digium card TE110P and after plug it, turn on the computer and
configure, the LEDs don't light up in spite of what Digium FAQ says about
the
LEDs:

When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP?
... The TE110P LED's will light up RED when the span is configured and
kernel
module is loaded. If configured correctly and a circuit or channel bank is
connected the LED should turn GREEN.
...

Below are the output of dmesg, lsmod, /etc/zaptel.conf and ztcfg -vvv. Did
anyone have this problem before?

Thanks
Ant?nio The?philo J?nior

root@paggo-asterisk01:~# dmesg | more
...
[42949385.790000] Zapata Telephony Interface Registered on major 196
[42949385.790000] Zaptel Version: 1.2.10 Echo Canceller: KB1
[42949385.840000] e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
[42949385.840000] e100: Copyright(c) 1999-2005 Intel Corporation
[42949385.960000] intel8x0_measure_ac97_clock: measured 61046 usecs
[42949385.960000] intel8x0: clocking to 48000
[42949385.970000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low)
-> IRQ 209
[42949385.970000] Controller version: 24
[42949385.970000] FALC version: 00000000
[42949385.970000] TE110P: Setting up global serial parameters for E1 FALC V1.2
[42949385.970000] TE110P: Successfully initialized serial bus for card
[42949385.970000] Found a Wildcard: Digium Wildcard TE110P T1/E1
[42949386.000000] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low)
-> IRQ 217
[42949386.020000] e100: eth0: e100_probe: addr 0xff8fe000, irq 217, MAC addr
00:0C:F1:E7:1B:0B
[42949386.060000] Registered tone zone 20 (Brazil)
[42949386.060000] TE110P: Span configured for CAS/HDB3
[42949386.060000] Calling startup (flags is 4099)
[42949386.100000] CSLIP: code copyright 1989 Regents of the University of
California
[42949386.130000] ISDN subsystem Rev:
1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded
[42949386.190000] HiSax: Linux Driver for passive ISDN cards
[42949386.190000] HiSax: Version 3.5 (module)
[42949386.190000] HiSax: Layer1 Revision 2.46.2.5
[42949386.190000] HiSax: Layer2 Revision 2.30.2.4
[42949386.190000] HiSax: TeiMgr Revision 2.20.2.3
[42949386.190000] HiSax: Layer3 Revision 2.22.2.3
[42949386.190000] HiSax: LinkLayer Revision 2.59.2.4
[42949386.380000] lp0: using parport0 (interrupt-driven).
...

root@paggo-asterisk01:~# lsmod
Module                  Size  Used by
ipv6                  287584  24
ext3                  147848  1
jbd                    62996  1 ext3
dm_mod                 63512  1
md_mod                 76756  0
lp                     13220  0
hisax                 575824  0
isdn                  153056  1 hisax
slhc                    8320  1 isdn
e100                   43012  0
mii                     7040  1 e100
wcte11xp               27424  0
zaptel                192900  1 wcte11xp
crc_ccitt               3200  2 hisax,zaptel
snd_intel8x0           36380  0
snd_ac97_codec        100512  1 snd_intel8x0
snd_ac97_bus            3328  1 snd_ac97_codec
snd_pcm_oss            56992  0
snd_mixer_oss          21248  1 snd_pcm_oss
snd_pcm                96516  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer              27140  1 snd_pcm
i2c_i810                6276  0
i2c_algo_bit           10760  1 i2c_i810
hw_random               6420  0
psmouse                40836  0
snd                    59748  6
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore              11232  1 snd
snd_page_alloc         12296  2 snd_intel8x0,snd_pcm
i2c_core               23296  1 i2c_algo_bit
shpchp                 50144  0
pci_hotplug            30652  1 shpchp
intel_agp              25628  1
agpgart                37580  1 intel_agp
parport_pc             38724  1
parport                39624  2 lp,parport_pc
serio_raw               8580  0
pcspkr                  3204  0
floppy                 65252  0
evdev                  11136  0
xfs                   648156  10
exportfs                7296  1 xfs
ide_generic             2432  0
ehci_hcd               34824  0
uhci_hcd               35984  0
usbcore               137732  3 ehci_hcd,uhci_hcd
ide_cd                 36740  0
cdrom                  42272  1 ide_cd
ide_disk               19968  13
piix                   12420  1
generic                 5892  0
thermal                14728  0
processor              27080  1 thermal
fan                     5764  0
capability              5896  0
commoncap               8192  1 capability
vga16fb                14856  1
vgastate               11136  1 vga16fb
fbcon                  44448  70
tileblit                3712  1 fbcon
font                    9216  1 fbcon
bitblit                 7424  1 fbcon
softcursor              3200  1 bitblit

root@paggo-asterisk01:~# more /etc/zaptel.conf | egrep -v '^#'

span=1,0,0,cas,hdb3
cas=1-15:1001
dchan=16
cas=17-31:1001

loadzone=br
defaultzone=br

root@paggo-asterisk01:~# ztcfg -vvvv

Zaptel Configuration
=====================
SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: CAS / User (Default) (Slaves: 01)
Channel 02: CAS / User (Default) (Slaves: 02)
Channel 03: CAS / User (Default) (Slaves: 03)
Channel 04: CAS / User (Default) (Slaves: 04)
Channel 05: CAS / User (Default) (Slaves: 05)
Channel 06: CAS / User (Default) (Slaves: 06)
Channel 07: CAS / User (Default) (Slaves: 07)
Channel 08: CAS / User (Default) (Slaves: 08)
Channel 09: CAS / User (Default) (Slaves: 09)
Channel 10: CAS / User (Default) (Slaves: 10)
Channel 11: CAS / User (Default) (Slaves: 11)
Channel 12: CAS / User (Default) (Slaves: 12)
Channel 13: CAS / User (Default) (Slaves: 13)
Channel 14: CAS / User (Default) (Slaves: 14)
Channel 15: CAS / User (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: CAS / User (Default) (Slaves: 17)
Channel 18: CAS / User (Default) (Slaves: 18)
Channel 19: CAS / User (Default) (Slaves: 19)
Channel 20: CAS / User (Default) (Slaves: 20)
Channel 21: CAS / User (Default) (Slaves: 21)
Channel 22: CAS / User (Default) (Slaves: 22)
Channel 23: CAS / User (Default) (Slaves: 23)
Channel 24: CAS / User (Default) (Slaves: 24)
Channel 25: CAS / User (Default) (Slaves: 25)
Channel 26: CAS / User (Default) (Slaves: 26)
Channel 27: CAS / User (Default) (Slaves: 27)
Channel 28: CAS / User (Default) (Slaves: 28)
Channel 29: CAS / User (Default) (Slaves: 29)
Channel 30: CAS / User (Default) (Slaves: 30)
Channel 31: CAS / User (Default) (Slaves: 31)

31 channels configured.

Esta mensagem pode conter informacao confidencial e/ou privilegiada. 
Se voce nao for o destinatario ou a pessoa autorizada a receber esta mensagem,
nao pode usar, copiar ou divulgar as informacoes nela contidas ou tomar qualquer
acao baseada nessas informacoes.

Se voce recebeu esta mensagem por engano, por favor avise imediatamente o
remetente, respondendo o e-mail e em seguida apague-o. Agradecemos sua
cooperacao.

This message may contain confidential or privileged information. If you are not
the addressee or authorized to receive this for the addressee, you must not use,
copy, disclose or take any action based on this message or any
information herein. If you have received this message in error, please advise
the sender immediately by reply e-mail and delete this message. Thank you for
your cooperation.