search for: basechan

...bchan=217-240 span=11,11,0,esf,b8zs bchan=241-264 span=12,12,0,esf,b8zs bchan=265-288 dahdi_scan : [1] active=yes alarms=OK description=T4XXP (PCI) Card 0 Span 1 name=TE4/0/1 manufacturer=Digium devicetype=Wildcard TE410P (3rd Gen) (VPMOCT128) location=Board ID Switch 0 basechan=1 totchans=24 irq=225 type=digital-T1 syncsrc=1 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI framing_opts=ESF,D4 coding=B8ZS framing=ESF [2] active=yes alarms=OK description=T4XXP (PCI) Card 0 Span 2 name=TE4/0/2 manufacturer=Digium devicetype=Wildcard TE410P (3rd Gen) (VP...

...pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16 type=digital-E1 syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=HDB3 framing_opts=CCS,CRC4 coding=HDB3 framing=CCS [2] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 2 name=TE2/0/2 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Swit...

...(Slaves: 02) 2 channels to configure. Setting echocan for channel 1 to mg2 Setting echocan for channel 2 to mg2 [root at pbx asterisk]# dahdi_scan [1] active=yes alarms=OK description=Wildcard X101P Board 1 name=WCFXO/0 manufacturer=Digium devicetype=Wildcard X101P location=PCI Bus 00 Slot 15 basechan=1 totchans=1 irq=11 type=analog port=1,FXO [2] active=yes alarms=OK description=Wildcard TDM400P REV E/F Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV E/F location=PCI Bus 00 Slot 14 basechan=2 totchans=4 irq=11 type=analog port=2,FXS port=3,none port=4,none port=5,none...

...01 Wildcard TDM400P REV E/F pci:0000:11:00.0 wcb4xxp+ d161:b410 Digium Wildcard B410P but ?dahdi_scan? just recognize the B410P: [1] active=yes alarms=RED description=B4XXP (PCI) Card 0 Span 1 name=B4/0/1 manufacturer=Digium devicetype=Wildcard B410P location=PCI Bus 17 Slot 01 basechan=1 totchans=3 irq=66 type=digital-TE syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI,HDB3 framing_opts=ESF,D4,CCS,CRC4 coding=AMI framing=CCS [2] active=yes alarms=RED description=B4XXP (PCI) Card 0 Span 2 name=B4/0/2 manufacturer=Digium devicetype=Wildcard B410P lo...

...[ OK ] Running dahdi_cfg: [ OK ] The dahdi_scan result is the following: [1] active=yes alarms=OK description=B4XXP (PCI) Card 0 Span 1 name=B4/0/1 manufacturer=Digium devicetype=Wildcard B410P location=PCI Bus 17 Slot 01 basechan=1 totchans=3 irq=66 type=digital-TE syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI,HDB3 framing_opts=ESF,D4,CCS,CRC4 coding=AMI framing=CCS [2] active=yes alarms=OK description=B4XXP (PCI) Card 0 Span 2 name=B4/0/2 manufacturer=Digium devicetype=Wildcard B410P loc...

...02.0 wcb4xxp+ 1397:08b4 Junghanns QuadBRI ISDN card ------------------------------------------ root at pbx:~ $ dahdi_scan [1] active=yes alarms=RED description=B4XXP (PCI) Card 0 Span 1 name=B4/0/1 manufacturer=Digium devicetype=HFC-4S Junghanns.NET quadBRI PCI location=PCI Bus 06 Slot 03 basechan=1 totchans=3 irq=78 type=digital-TE syncsrc=0 lbo=399-533 feet (DSX-1) coding_opts=B8ZS,AMI,HDB3 framing_opts=ESF,D4,CCS,CRC4 coding=AMI framing=CCS [2] active=yes alarms=RED description=B4XXP (PCI) Card 0 Span 2 name=B4/0/2 manufacturer=Digium devicetype=HFC-4S Junghanns.NET quadBRI PCI location=P...

...I Tools Version - 2.1.0.2 DAHDI Version: 2.1.0.4 Echo Canceller(s): Configuration ====================== 0 channels to configure. dahdi_scan: [1] active=yes alarms=UNCONFIGURED description=DAHDI_DUMMY/1 (source: HRtimer) 1 name=DAHDI_DUMMY/1 manufacturer= devicetype=DAHDI Dummy Timing location= basechan=1 totchans=0 irq=0 Nada parece funcionar y realmente no se donde esta el error... alguna idea?

...some documentation on what _could_ cause a (cause 0 - Unknown) then I can investigate those. Some details below: geriatrix ~ # dahdi_scan [1] active=yes alarms=OK description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE210P (4th Gen) location=Board ID Switch 0 basechan=1 totchans=24 irq=48 type=digital-T1 syncsrc=1 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI framing_opts=ESF,D4 coding=B8ZS framing=ESF [2] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 2 name=TE2/0/2 manufacturer=Digium devicetype=Wildcard TE210P (4th Gen) location=Board ID S...

...0 09:20:36] WARNING[32270] chan_dahdi.c: No D-channels available! Using Primary channel 16 as D-channel anyway! gentoo1 ~ # dahdi_scan [1] active=yes alarms=LMFA/OK description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (5th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16 type=digital-E1 syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=AMI,HDB3 framing_opts=CCS,CRC4 coding=HDB3 framing=CCS/CRC4 [2] active=yes alarms=LMFA/OK description=T2XXP (PCI) Card 0 Span 2 name=TE2/0/2 manufacturer=Digium devicetype=Wildcard TE220 (5th Gen) location=...

...ear RED 21 TE2/0/1/21 Clear RED 22 TE2/0/1/22 Clear RED 23 TE2/0/1/23 Clear RED 24 TE2/0/1/24 HDLCFCS RED 5. dahdi_scan [1] active=yes alarms=BLU/RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE210P location=Board ID Switch 0 basechan=1 totchans=24 irq=22 type=digital-T1 syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI framing_opts=ESF,D4 coding=B8ZS framing=ESF [2] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 2 name=TE2/0/2 manufacturer=Digium devicetype=Wildcard TE210P location=Board ID Switch 0 ba...

...| Connected | wanpipe2 | AFT TE1 | N/A | Disconnected | wanpipe3 | AFT TE1 | N/A | Disconnected | wanpipe4 | AFT TE1 | N/A | Disconnected | However: # dahdi_scan 2 [2] active=yes alarms=OK description=wanpipe2 card 1 name=WPE1/1 manufacturer= devicetype= location= basechan=1 totchans=31 irq=0 type=digital- syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=HDB3 framing_opts=CCS,CRC4 coding=HDB3 framing=CCS Why are the dahdi tools not reflecting the values by wanrouter? Roger.

...pri show version libpri version: 1.4.10.2 brs-dev*CLI> dahdi show version DAHDI Version: 2.3.0 Echo Canceller: KB1 Each LED is green but dahdi_scan says : # dahdi_scan [1] active=yes alarms=OK description=quadBRI PCI ISDN Card 1 Span 1 [TE] (ca name=ztqoz/1/1 manufacturer= devicetype= location= basechan=1 totchans=3 irq=0 type=digital- syncsrc=0 lbo=399-533 feet (DSX-1) coding_opts=AMI framing_opts=CCS coding=AMI framing=CCS 1. Is this syncsrc=0 normal (we're in TE mode) ? 2. Am I correct to hope "pri show spans" to display something ? 3. Suggestions ? Regards -------------- next...

...hdi with no luck. The other two cards are working fine. I put a loop plug the ports and same problem. dahdi_scan [9] active=yes alarms=RED/LFA/LMFA description=T4XXP (PCI) Card 2 Span 1 name=TE4/2/1 manufacturer=Digium devicetype=Wildcard TE410P (4th Gen) (VPMOCT128) location=PCI Bus 10 Slot 04 basechan=193 totchans=24 irq=50 type=digital-T1 syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=B8ZS,AMI framing_opts=ESF,D4 coding=B8ZS framing=ESF [10] active=yes alarms=RED/LFA/LMFA description=T4XXP (PCI) Card 2 Span 2 name=TE4/2/2 manufacturer=Digium devicetype=Wildcard TE410P (4th Gen) (VPMOCT...

...doesn't work either, and now I'm confused. dahdi_scan recognizes the s110, but it says it fails. Output looks like this: [2] active=yes alarms=OK description=Wildcard TDM400P REV E/F Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV E/F location=PCI Bus 05 Slot 01 basechan=5 totchans=4 irq=169 type=analog port=5,FXO port=6,FXO port=7,FXO port=8,FXS FAILED I tried moving both the s110s to other positions on the TDM400, but it fails in all of them. Is this a power issue? The system it's in only has sata power connectors, so I had to splice on an ide power connec...

...r device [Sep 1 10:57:51] ERROR[31696]: chan_dahdi.c:14170 build_channels: Unable to register channel '1' # dahdi_scan [1] active=yes alarms=OK description=Wildcard AEX410 Board 1 name=WCTDM/0 manufacturer=Digium devicetype=Wildcard AEX410 with VPMADT032 location=PCI Express Bus 11 Slot 09 basechan=1 totchans=4 irq=16 [2] active=yes alarms=UNCONFIGURED description=DAHDI_DUMMY/1 (source: HRtimer) 1 name=DAHDI_DUMMY/1 manufacturer= devicetype=DAHDI Dummy Timing location= basechan=5 totchans=0 irq=0 Note, I have compiled DAHDI 2.2.0.2 but it still shows 2.1.0.4 in the tool. Version bug? If it s...

...n 1. Another thing that I find odd is the output of dadhi_scan, that indicates that syncsrc=0 for all spans. Is that correct? [1] active=yes alarms=OK description=T4XXP (PCI) Card 0 Span 1 name=TE4/0/1 manufacturer=Digium devicetype=Wildcard TE420 (4th Gen) (VPMOCT128) location=Board ID Switch 0 basechan=1 totchans=31 irq=177 type=digital-E1 syncsrc=0 lbo=0 db (CSU)/0-133 feet (DSX-1) coding_opts=HDB3 framing_opts=CCS,CRC4 coding=HDB3 framing=CCS [2] active=yes alarms=OK description=T4XXP (PCI) Card 0 Span 2 name=TE4/0/2 manufacturer=Digium devicetype=Wildcard TE420 (4th Gen) (VPMOCT128) location=B...

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

...P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK description=Wildcard TDM400P REV E/F Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV E/F location=PCI Bus 02 Slot 02 basechan=1 totchans=4 irq=169 type=analog port=1,FXO port=2,none port=3,none port=4,none /etc/dahdi/system.conf ---------------------- fxsks=1 echocanceller=mg2,1 loadzone = uk defaultzone = uk dmesg when loaded dadhi ----------------------- dahdi: Telephony Interface Registered on major 196 da...

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the