Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver http://webservices.jnetdns.de/~junghanns.net/downloads/jnet-dahdi-drivers-1.0.1.tar.gz - every jumper set to TE mode When typing "pri show spans", Asterisk replies nothing : brs-dev*CLI> pri show spans brs-dev*CLI> pri show version libpri version: 1.4.10.2 brs-dev*CLI> dahdi show version DAHDI Version: 2.3.0 Echo Canceller: KB1 Each LED is green but dahdi_scan says : # dahdi_scan [1] active=yes alarms=OK description=quadBRI PCI ISDN Card 1 Span 1 [TE] (ca name=ztqoz/1/1 manufacturerdevicetypelocationbasechan=1 totchans=3 irq=0 type=digital- syncsrc=0 lbo=399-533 feet (DSX-1) coding_opts=AMI framing_opts=CCS coding=AMI framing=CCS 1. Is this syncsrc=0 normal (we're in TE mode) ? 2. Am I correct to hope "pri show spans" to display something ? 3. Suggestions ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100508/cefb7b07/attachment.htm
2010/5/8 Olivier <oza_4h07 at yahoo.fr>> Hi, > > I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. > I'm only getting this : > [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to > create channel of type 'DAHDI' (cause 0 - Unknown) > > My setup is : > Asterisk 1.6.1.18 > libpri 1.4.10.2 > 1 Junghanns QuadBRI PCI-E express with : > - driver > http://webservices.jnetdns.de/~junghanns.net/downloads/jnet-dahdi-drivers-1.0.1.tar.gz<http://webservices.jnetdns.de/%7Ejunghanns.net/downloads/jnet-dahdi-drivers-1.0.1.tar.gz> > - every jumper set to TE mode > > > When typing "pri show spans", Asterisk replies nothing : > brs-dev*CLI> pri show spans > brs-dev*CLI> pri show version > libpri version: 1.4.10.2 > brs-dev*CLI> dahdi show version > DAHDI Version: 2.3.0 Echo Canceller: KB1 > > Each LED is green but dahdi_scan says : > # dahdi_scan > [1] > active=yes > alarms=OK > description=quadBRI PCI ISDN Card 1 Span 1 [TE] (ca > name=ztqoz/1/1 > manufacturer> devicetype> location> basechan=1 > totchans=3 > irq=0 > type=digital- > syncsrc=0 > lbo=399-533 feet (DSX-1) > coding_opts=AMI > framing_opts=CCS > coding=AMI > framing=CCS > > > 1. Is this syncsrc=0 normal (we're in TE mode) ? > 2. Am I correct to hope "pri show spans" to display something ? > 3. Suggestions ? > > Regards > > I should have said I've tried unsuccessfully with both dahdi 2.2.1.1 and2.3. I'm really wondering if PCI-E QuadBRI are supported. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100508/b8e2dade/attachment.htm