samba - May 2003 - Setting up CUPS for Samba on 390

I've scoured the newsgroups and asked MANY people, does anyone out there 
have any ideas ?

I'm new to the CUPS arena and I'm trying to figure out what to do from 
the separate docs.  I'm using SLES7 (2.4.7 kernel).  The files I'm using
are:

4368072 May 22 06:22 cups-1.1.19rc5-source.tar.gz
197341 May 22 06:22 cups-samba-1.1.19rc2.tar.gz
4961128 May 22 07:58 ghostscript-7.05.tar.gz
14520320 May 22 06:22 gimp-print-4.3.14.tar
610697 May 23 06:20 pkgconfig-0.15.0.tar.gz
5463358 May 22 06:24 samba-2.2.8a.tar.gz

So far I have compiled cups, ghostscript (with the cups patch), cups-
samba drivers, & samba with cups enabled.

I have setup my smb.conf file to use cups and I can see the printer I 
setup through Network Neigh.  I used the windows interface to install the 
printer driver and I can install the driver onto my client through the 
APW interface.  When I try to print I get "test page failed to print"
I'm guessing it's because I don't have the gimp-print package
installed
yet, and that's where I'm stuck.

When I ran "./configure --with-cups --without-gimp
--disable-gimp-test"
for the gimp-print package I got errors about not finding glib-config and 
pkg-config.  I found the pkgconfig package at the url listed in the 
error.  I did the usual configure,make,make install, but then it gave 
errors about not finding .h files.  I went through one at a time moving 
them to the /usr/local/include directory because apparently the make 
install doesn't do that.  

Now I still get errors surrounding glib-config and pkg-config.

Am I going down the right path here ?  I've 

TIA

Josh

Josh Konkol samba at guidemail.com
> Fri May 23 13:41:28 GMT 2003
> 
> 
> I've scoured the newsgroups and asked MANY people, does anyone out
there
> have any ideas ?
Here!
> I'm new to the CUPS arena and I'm trying to figure out what to do
from
> the separate docs.  I'm using SLES7 (2.4.7 kernel).  The files I'm
using
> are:
> 
> 4368072 May 22 06:22 cups-1.1.19rc5-source.tar.gz
> 197341 May 22 06:22 cups-samba-1.1.19rc2.tar.gz
> 4961128 May 22 07:58 ghostscript-7.05.tar.gz
> 14520320 May 22 06:22 gimp-print-4.3.14.tar
> 610697 May 23 06:20 pkgconfig-0.15.0.tar.gz
> 5463358 May 22 06:24 samba-2.2.8a.tar.gz
> 
> So far I have compiled cups, ghostscript (with the cups patch), cups-
> samba drivers, 
You seem to be on a wrong track here. The cups-samba drivers don't
need to be compiled. They arrive as pre-compiled binaries.
> & samba with cups enabled.
> 
> I have setup my smb.conf file to use cups and I can see the printer I 
> setup through Network Neigh.  I used the windows interface to install the 
> printer driver 
What do you mean "used the windows interface to install the printer
driver" ?

* The CUPS-Samba drivers are installed with "cupsaddsmb" (*not* the
Windows
   "Add Printer Wizard") into the [print$] share on the Samba side.

* To install them on a [WinNT/2K/XP] client, use the usual
"Point'n'Print"
   method familiar to many WinNT admins.
> and I can install the driver onto my client through the 
> APW interface.  When I try to print I get "test page failed to
print"
Probably you need to "set the correct Device Mode" first....

Please check out this documentation and see if it helps you:

    http://www.linuxprinting.org/kpfeifle/SambaPrintHOWTO/

The sections about the Device Mode are f.e. here:

   
http://www.linuxprinting.org/kpfeifle/SambaPrintHOWTO/Samba-HOWTO-Collection-3.0-PrintingChapter-9th-draft.html#11_2_10

I am currently working on some minor clarifications about the CUPS-Samba
driver files.

A new version of that document's draft should be uploaded by Sunday
evening (European time).


[....]
> 
> Josh
> 
Cheers,
Kurt