Steven Timm
2008-Apr-18 01:24 UTC
[Xen-users] help--dom0 network goes unpingable when xend starts
I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way.>From lspci04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) from lspci Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006) ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 16, node addr 0019b9ec40ba ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 16, node addr 0019b9ec40b8 --------------- note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 from what the redhatized non-xen kernel does. This is undone by ifcfg-eth0. When the xen kernel boots, before xend starts, I can see the outside network just fine. [root@fnpcsrv3 xen]# netstat -nNr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 eth0 [root@fnpcsrv3 xen]# ifconfig eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 inet addr:131.225.166.97 Bcast:131.225.167.255 Mask:255.255.254.0 inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) Interrupt:16 Memory:f8000000-f8011100 eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f4000000-f4011100 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) -------------------------------------------------------------- Now here''s ifconfig from an identical system once xend is turned on [root@fnpcsrv5 ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 inet addr:131.225.166.100 Bcast:131.225.167.255 Mask:255.255.254.0 inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:21 errors:0 dropped:0 overruns:0 frame:0 TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) Interrupt:16 Memory:f4000000-f4011100 vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) ------------------------------------------------------------------------ As part of the debugging I dialed back my configuration, which normally has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one network interface on each domU and on the dom0. Nevertheless the problem is the same and I can''t seem to get rid of the xenbr1. I note that at the start of the xend there is a timeout of about 10-15 seconds as it is trying to turn on the second bridge. Now here is the really strange part. While logged in on the console of the dom0, I can go ahead and start xen domU''s, and they go ahead and boot up normally and can see the outside network fine. [root@fnpcsrv5 ~]# xm list Name ID Mem VCPUs State Time(s) Domain-0 0 1953 8 r----- 127.3 fnpc5x1 1 6000 4 -b---- 23.1 fnpc5x4 2 2000 1 -b---- 20.6 [root@fnpcsrv5 ~]# Oh, and by the way, dom0 is pingable from the domU''s although it cannot be seen from the outside net. What should I be looking at? Steve Timm ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Steven Timm
2008-Apr-18 03:35 UTC
[Xen-users] Re: help--dom0 network goes unpingable when xend starts
Six more things about the situation below: 1) network guys have checked out the switch and give us a clean bill of health. 2) I see this problem on 3 identical machines, each time I lose the network when I start up the xend. 3) Dell poweredge 2950 (which works) as compared to dell poweredge1950 (which doesn''t)--one possible difference is that there is a 2nd mac address associated with the port which is normally the eth0 on the PE 1950, used for the IPMI controller. but I disabled this, and also switched the cable to the other port which doesn''t have the extra mac. same problem as before., 4) i reported below that the domu''s can ping the dom0. Turns out that the dom0 can ping the domu''s too. and 5) netstat -a on the non-working machine doesn''t show all the bridges that normally show up. 6) Theres a 169.254.0.0 route of unknown origin on this machine on the same interface that I''m trying to use. Is there any idea--what to strace? what to tcpdump? Steve ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. On Thu, 17 Apr 2008, Steven Timm wrote:> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on > three new machines today, using a configuration setup that I''ve > used successfully many times before. However, I encountered a > new problem. > > These are Dell Poweredge 1950 servers, by the way. > From lspci > 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > > from lspci > Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006) > ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found > at > mem f4000000, IRQ 16, node addr 0019b9ec40ba > ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found > at > mem f8000000, IRQ 16, node addr 0019b9ec40b8 > > --------------- > > note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 > from what the redhatized non-xen kernel does. This is > undone by ifcfg-eth0. > > When the xen kernel boots, before xend starts, I can see the outside network > just fine. > > [root@fnpcsrv3 xen]# netstat -nNr > Kernel IP routing table > Destination Gateway Genmask Flags MSS Window irtt > Iface > 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 > 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 eth0 > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 > 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 eth0 > > > [root@fnpcsrv3 xen]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 > inet addr:131.225.166.97 Bcast:131.225.167.255 Mask:255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) > Interrupt:16 Memory:f8000000-f8011100 > > eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA > inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:16 Memory:f4000000-f4011100 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:192 errors:0 dropped:0 overruns:0 frame:0 > TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) > -------------------------------------------------------------- > > Now here''s ifconfig from an identical system once xend is turned on > > [root@fnpcsrv5 ~]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 > inet addr:131.225.166.100 Bcast:131.225.167.255 Mask:255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 > TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:21 errors:0 dropped:0 overruns:0 frame:0 > TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) > > peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 > TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) > Interrupt:16 Memory:f4000000-f4011100 > > vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:33 errors:0 dropped:0 overruns:0 frame:0 > TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) > > vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 > TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) > > vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 > TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) > > xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) > > xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) > > ------------------------------------------------------------------------ > > As part of the debugging I dialed back my configuration, which normally > has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one > network interface on each domU and on the dom0. Nevertheless the > problem is the same and I can''t seem to get rid of the xenbr1. > I note that at the start of the xend there is a timeout of about 10-15 > seconds as it is trying to turn on the second bridge. > > Now here is the really strange part. While logged in on the > console of the dom0, I can go ahead and start xen domU''s, and they > go ahead and boot up normally and can see the outside network fine. > > [root@fnpcsrv5 ~]# xm list > Name ID Mem VCPUs State Time(s) > Domain-0 0 1953 8 r----- 127.3 > fnpc5x1 1 6000 4 -b---- 23.1 > fnpc5x4 2 2000 1 -b---- 20.6 > [root@fnpcsrv5 ~]# > > Oh, and by the way, dom0 is pingable from the domU''s although > it cannot be seen from the outside net. > > What should I be looking at? > > Steve Timm > > > > ------------------------------------------------------------------ > Steven C. Timm, Ph.D (630) 840-8525 > timm@fnal.gov http://home.fnal.gov/~timm/ > Fermilab Computing Division, Scientific Computing Facilities, > Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Todd Deshane
2008-Apr-21 21:20 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
On Thu, Apr 17, 2008 at 9:24 PM, Steven Timm <timm@fnal.gov> wrote:> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on > three new machines today, using a configuration setup that I''ve > used successfully many times before. However, I encountered a > new problem. > > These are Dell Poweredge 1950 servers, by the way. > > > From lspci > > > 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > > from lspci > Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, > 2006) > ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz > found at > mem f4000000, IRQ 16, node addr 0019b9ec40ba > ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz > found at > mem f8000000, IRQ 16, node addr 0019b9ec40b8 > > --------------- > > note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 > from what the redhatized non-xen kernel does. This is > undone by ifcfg-eth0. > > When the xen kernel boots, before xend starts, I can see the outside > network just fine. > > [root@fnpcsrv3 xen]# netstat -nNr > Kernel IP routing table > Destination Gateway Genmask Flags MSS Window irtt > Iface > 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 > eth1 > 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 > eth0 > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 > eth1 > 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 > eth0 > > > [root@fnpcsrv3 xen]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 > inet addr:131.225.166.97 Bcast:131.225.167.255 Mask: > 255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) > Interrupt:16 Memory:f8000000-f8011100 > > eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA > inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:16 Memory:f4000000-f4011100 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:192 errors:0 dropped:0 overruns:0 frame:0 > TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) > -------------------------------------------------------------- > > Now here''s ifconfig from an identical system once xend is turned on > > [root@fnpcsrv5 ~]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 > inet addr:131.225.166.100 Bcast:131.225.167.255 Mask: > 255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 > TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:21 errors:0 dropped:0 overruns:0 frame:0 > TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) > > peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 > TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) > Interrupt:16 Memory:f4000000-f4011100 > > vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:33 errors:0 dropped:0 overruns:0 frame:0 > TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) > > vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 > TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) > > vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 > TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) > > xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) > > xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) > > ------------------------------------------------------------------------ > > As part of the debugging I dialed back my configuration, which normally > has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one > network interface on each domU and on the dom0. Nevertheless the > problem is the same and I can''t seem to get rid of the xenbr1. > I note that at the start of the xend there is a timeout of about 10-15 > seconds as it is trying to turn on the second bridge. > > Now here is the really strange part. While logged in on the > console of the dom0, I can go ahead and start xen domU''s, and they > go ahead and boot up normally and can see the outside network fine. > > [root@fnpcsrv5 ~]# xm list > Name ID Mem VCPUs State > Time(s) > Domain-0 0 1953 8 r----- > 127.3 > fnpc5x1 1 6000 4 -b---- > 23.1 > fnpc5x4 2 2000 1 -b---- > 20.6 > [root@fnpcsrv5 ~]# > > Oh, and by the way, dom0 is pingable from the domU''s although > it cannot be seen from the outside net. > > What should I be looking at? >Could you also provide the output of: brctl show grep net /etc/xen/xend-config.sxp | grep -v ''#'' Also, in the domU config files what are you specifying for the bridge? Are you running any custom network scripts (these would be specified in /etc/xen/xend-config.sxp and should have shown up in the output of the grep above. Cheers, Todd> Steve Timm > > > > ------------------------------------------------------------------ > Steven C. Timm, Ph.D (630) 840-8525 > timm@fnal.gov http://home.fnal.gov/~timm/ <http://home.fnal.gov/%7Etimm/> > Fermilab Computing Division, Scientific Computing Facilities, > Grid Facilities Department, FermiGrid Services Group, Assistant Group > Leader. > > _______________________________________________ > Xen-users mailing list > Xen-users@lists.xensource.com > http://lists.xensource.com/xen-users >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Steven Timm
2008-Apr-28 15:39 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
Here''s the output of [root@fnpcsrv5 ~]# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.feffffffffff no vif2.0 vif1.0 peth0 vif0.0 xenbr1 8000.000000000000 no and here''s xend-config.sxp [root@fnpcsrv5 xen]# grep net xend-config.sxp | grep -v ^# (network-script network-bridge) And here''s what the domU config files show at the moment: vif = [ ''mac=00:16:3e:0f:05:01, bridge=xenbr0'' ] ------------ I was at one point running a second bridge, but took it out during the debugging. Nevertheless the xenbr1 doesn''t go away. and I haven''t figured out any brctl commands that will make it go away.>From a similarly-configured working machine on different hardware, thisis what I wanted to do (and what I had originally configured on this one too), and has been working fine for me on many other machines. [root@fermigrid5 ~]# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.feffffffffff no vif12.0 vif10.0 vif9.0 vif8.0 vif7.0 peth0 vif0.0 xenbr1 8000.feffffffffff no vif12.1 vif10.1 vif9.1 vif8.1 vif7.1 peth1 vif0. ------------------------------- [root@fermigrid5 xen]# grep net xend-config.sxp | grep -v ^# (network-script my-network-bridge) [root@fermigrid5 xen]# more scripts/my-network-bridge #!/bin/sh # start bridges on both eth0 and eth1 XENDIR="/etc/xen/scripts" $XENDIR/network-bridge "$@" netdev=eth0 bridge=xenbr0 vifnum=0 $XENDIR/network-bridge "$@" netdev=eth1 bridge=xenbr1 vifnum=1 [root@fermigrid5 xen]# vif = [ ''mac=00:16:3e:05:05:01, bridge=xenbr0'', ''mac=00:16:3e:05:05:0a, bridge=xenbr1'' ] Hope this helps us figure out what is wrong. Have seen a couple places on the net that a bios upgrade and-or tweak to the broadcom controller is needed for the PE1950 to fix related problems. Has anyone tried? Steve Timm On Mon, 21 Apr 2008, Todd Deshane wrote:> On Thu, Apr 17, 2008 at 9:24 PM, Steven Timm <timm@fnal.gov> wrote: > >> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on >> three new machines today, using a configuration setup that I''ve >> used successfully many times before. However, I encountered a >> new problem. >> >> These are Dell Poweredge 1950 servers, by the way. >> >>> From lspci >>> >> 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >> Gigabit Ethernet (rev 12) >> 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >> Gigabit Ethernet (rev 12) >> >> from lspci >> Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, >> 2006) >> ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >> eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >> found at >> mem f4000000, IRQ 16, node addr 0019b9ec40ba >> ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >> eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >> found at >> mem f8000000, IRQ 16, node addr 0019b9ec40b8 >> >> --------------- >> >> note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 >> from what the redhatized non-xen kernel does. This is >> undone by ifcfg-eth0. >> >> When the xen kernel boots, before xend starts, I can see the outside >> network just fine. >> >> [root@fnpcsrv3 xen]# netstat -nNr >> Kernel IP routing table >> Destination Gateway Genmask Flags MSS Window irtt >> Iface >> 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 >> eth1 >> 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 >> eth0 >> 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 >> eth1 >> 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 >> eth0 >> >> >> [root@fnpcsrv3 xen]# ifconfig >> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 >> inet addr:131.225.166.97 Bcast:131.225.167.255 Mask: >> 255.255.254.0 >> inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) >> Interrupt:16 Memory:f8000000-f8011100 >> >> eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA >> inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 >> UP BROADCAST MULTICAST MTU:1500 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) >> Interrupt:16 Memory:f4000000-f4011100 >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:16436 Metric:1 >> RX packets:192 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) >> -------------------------------------------------------------- >> >> Now here''s ifconfig from an identical system once xend is turned on >> >> [root@fnpcsrv5 ~]# ifconfig >> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 >> inet addr:131.225.166.100 Bcast:131.225.167.255 Mask: >> 255.255.254.0 >> inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:16436 Metric:1 >> RX packets:21 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) >> >> peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) >> Interrupt:16 Memory:f4000000-f4011100 >> >> vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:33 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) >> >> vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 >> collisions:0 txqueuelen:32 >> RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) >> >> vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 >> collisions:0 txqueuelen:32 >> RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) >> >> xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) >> >> xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 >> inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) >> >> ------------------------------------------------------------------------ >> >> As part of the debugging I dialed back my configuration, which normally >> has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one >> network interface on each domU and on the dom0. Nevertheless the >> problem is the same and I can''t seem to get rid of the xenbr1. >> I note that at the start of the xend there is a timeout of about 10-15 >> seconds as it is trying to turn on the second bridge. >> >> Now here is the really strange part. While logged in on the >> console of the dom0, I can go ahead and start xen domU''s, and they >> go ahead and boot up normally and can see the outside network fine. >> >> [root@fnpcsrv5 ~]# xm list >> Name ID Mem VCPUs State >> Time(s) >> Domain-0 0 1953 8 r----- >> 127.3 >> fnpc5x1 1 6000 4 -b---- >> 23.1 >> fnpc5x4 2 2000 1 -b---- >> 20.6 >> [root@fnpcsrv5 ~]# >> >> Oh, and by the way, dom0 is pingable from the domU''s although >> it cannot be seen from the outside net. >> >> What should I be looking at? >> > > > Could you also provide the output of: > > brctl show > > grep net /etc/xen/xend-config.sxp | grep -v ''#'' > > Also, in the domU config files what are you specifying for the bridge? > > Are you running any custom network scripts (these would be specified in > /etc/xen/xend-config.sxp and should have shown up in the output of the grep > above. > > Cheers, > Todd > > >> Steve Timm >> >> >> >> ------------------------------------------------------------------ >> Steven C. Timm, Ph.D (630) 840-8525 >> timm@fnal.gov http://home.fnal.gov/~timm/ <http://home.fnal.gov/%7Etimm/> >> Fermilab Computing Division, Scientific Computing Facilities, >> Grid Facilities Department, FermiGrid Services Group, Assistant Group >> Leader. >> >> _______________________________________________ >> Xen-users mailing list >> Xen-users@lists.xensource.com >> http://lists.xensource.com/xen-users >> >-- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Todd Deshane
2008-Apr-28 16:02 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
To get rid of the xenbr1 manually, you should be able to do: brctl delif <any interface that is on that bridge> then, when no more interfaces do: ifconfig xenbr1 down brctl delbr xenbr1 Do you get any warning or error to stdout or to the /var/log/xen/* log files when starting/restarting xend? Have you tried to start the network-bridge script on the command line manually with: /etc/xen/scripts/network-bridge start It is also not clear to me anymore what works and what doesn''t. Could you clarify that again? Thanks, Todd On Mon, Apr 28, 2008 at 11:39 AM, Steven Timm <timm@fnal.gov> wrote:> Here''s the output of > > [root@fnpcsrv5 ~]# brctl show > bridge name bridge id STP enabled interfaces > xenbr0 8000.feffffffffff no vif2.0 > vif1.0 > peth0 > vif0.0 > xenbr1 8000.000000000000 no > > and here''s xend-config.sxp > > [root@fnpcsrv5 xen]# grep net xend-config.sxp | grep -v ^# > (network-script network-bridge) > > And here''s what the domU config files show at the moment: > > vif = [ ''mac=00:16:3e:0f:05:01, bridge=xenbr0'' ] > > > > ------------ > I was at one point running a second bridge, but took it out > during the debugging. Nevertheless the xenbr1 doesn''t go away. > and I haven''t figured out any brctl commands that will make it go away. > > From a similarly-configured working machine on different hardware, this > is what I wanted to do (and what I had originally configured on this one > too), and has been working fine for me on many other > machines. > > > [root@fermigrid5 ~]# brctl show > bridge name bridge id STP enabled interfaces > xenbr0 8000.feffffffffff no vif12.0 > vif10.0 > vif9.0 > vif8.0 > vif7.0 > peth0 > vif0.0 > xenbr1 8000.feffffffffff no vif12.1 > vif10.1 > vif9.1 > vif8.1 > vif7.1 > peth1 > vif0. > > > ------------------------------- > > [root@fermigrid5 xen]# grep net xend-config.sxp | grep -v ^# > (network-script my-network-bridge) > [root@fermigrid5 xen]# more scripts/my-network-bridge > #!/bin/sh > # start bridges on both eth0 and eth1 > > XENDIR="/etc/xen/scripts" > > $XENDIR/network-bridge "$@" netdev=eth0 bridge=xenbr0 vifnum=0 > $XENDIR/network-bridge "$@" netdev=eth1 bridge=xenbr1 vifnum=1 > [root@fermigrid5 xen]# > > vif = [ ''mac=00:16:3e:05:05:01, bridge=xenbr0'', ''mac=00:16:3e:05:05:0a, > bridge=xenbr1'' ] > > Hope this helps us figure out what is wrong. > > Have seen a couple places on the net that a bios upgrade > and-or tweak to the broadcom controller is needed > for the PE1950 to fix related problems. Has anyone tried? > > Steve Timm > > > > > > On Mon, 21 Apr 2008, Todd Deshane wrote: > > > > > > > > > > On Thu, Apr 17, 2008 at 9:24 PM, Steven Timm <timm@fnal.gov> wrote: > > > > > > > I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on > > > three new machines today, using a configuration setup that I''ve > > > used successfully many times before. However, I encountered a > > > new problem. > > > > > > These are Dell Poweredge 1950 servers, by the way. > > > > > > > > > > From lspci > > > > > > > > > > > 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > > > Gigabit Ethernet (rev 12) > > > 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > > > Gigabit Ethernet (rev 12) > > > > > > from lspci > > > Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, > > > 2006) > > > ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > > > eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz > > > found at > > > mem f4000000, IRQ 16, node addr 0019b9ec40ba > > > ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > > > eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz > > > found at > > > mem f8000000, IRQ 16, node addr 0019b9ec40b8 > > > > > > --------------- > > > > > > note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 > > > from what the redhatized non-xen kernel does. This is > > > undone by ifcfg-eth0. > > > > > > When the xen kernel boots, before xend starts, I can see the outside > > > network just fine. > > > > > > [root@fnpcsrv3 xen]# netstat -nNr > > > Kernel IP routing table > > > Destination Gateway Genmask Flags MSS Window irtt > > > Iface > > > 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 > > > eth1 > > > 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 > > > eth0 > > > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 > > > eth1 > > > 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 > > > eth0 > > > > > > > > > [root@fnpcsrv3 xen]# ifconfig > > > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 > > > inet addr:131.225.166.97 Bcast:131.225.167.255 Mask: > > > 255.255.254.0 > > > inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > > RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) > > > Interrupt:16 Memory:f8000000-f8011100 > > > > > > eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA > > > inet addr:192.168.167.3 Bcast:192.168.167.255 > Mask:255.255.255.0 > > > UP BROADCAST MULTICAST MTU:1500 Metric:1 > > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > > Interrupt:16 Memory:f4000000-f4011100 > > > > > > lo Link encap:Local Loopback > > > inet addr:127.0.0.1 Mask:255.0.0.0 > > > inet6 addr: ::1/128 Scope:Host > > > UP LOOPBACK RUNNING MTU:16436 Metric:1 > > > RX packets:192 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) > > > -------------------------------------------------------------- > > > > > > Now here''s ifconfig from an identical system once xend is turned on > > > > > > [root@fnpcsrv5 ~]# ifconfig > > > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 > > > inet addr:131.225.166.100 Bcast:131.225.167.255 Mask: > > > 255.255.254.0 > > > inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > > RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) > > > > > > lo Link encap:Local Loopback > > > inet addr:127.0.0.1 Mask:255.0.0.0 > > > inet6 addr: ::1/128 Scope:Host > > > UP LOOPBACK RUNNING MTU:16436 Metric:1 > > > RX packets:21 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) > > > > > > peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > > > RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:1000 > > > RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) > > > Interrupt:16 Memory:f4000000-f4011100 > > > > > > vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > > > RX packets:33 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) > > > > > > vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > > > RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 > > > collisions:0 txqueuelen:32 > > > RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) > > > > > > vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > > > RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 > > > collisions:0 txqueuelen:32 > > > RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) > > > > > > xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > > RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) > > > > > > xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 > > > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > > TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 > > > collisions:0 txqueuelen:0 > > > RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) > > > > > > ------------------------------------------------------------------------ > > > > > > As part of the debugging I dialed back my configuration, which normally > > > has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one > > > network interface on each domU and on the dom0. Nevertheless the > > > problem is the same and I can''t seem to get rid of the xenbr1. > > > I note that at the start of the xend there is a timeout of about 10-15 > > > seconds as it is trying to turn on the second bridge. > > > > > > Now here is the really strange part. While logged in on the > > > console of the dom0, I can go ahead and start xen domU''s, and they > > > go ahead and boot up normally and can see the outside network fine. > > > > > > [root@fnpcsrv5 ~]# xm list > > > Name ID Mem VCPUs State > > > Time(s) > > > Domain-0 0 1953 8 r----- > > > 127.3 > > > fnpc5x1 1 6000 4 -b---- > > > 23.1 > > > fnpc5x4 2 2000 1 -b---- > > > 20.6 > > > [root@fnpcsrv5 ~]# > > > > > > Oh, and by the way, dom0 is pingable from the domU''s although > > > it cannot be seen from the outside net. > > > > > > What should I be looking at? > > > > > > > > > > > > Could you also provide the output of: > > > > brctl show > > > > grep net /etc/xen/xend-config.sxp | grep -v ''#'' > > > > Also, in the domU config files what are you specifying for the bridge? > > > > Are you running any custom network scripts (these would be specified in > > /etc/xen/xend-config.sxp and should have shown up in the output of the > grep > > above. > > > > Cheers, > > Todd > > > > > > > > > > > > > > > > > > Steve Timm > > > > > > > > > > > > ------------------------------------------------------------------ > > > Steven C. Timm, Ph.D (630) 840-8525 > > > timm@fnal.gov http://home.fnal.gov/~timm/ > <http://home.fnal.gov/%7Etimm/> > > > > > > Fermilab Computing Division, Scientific Computing Facilities, > > > Grid Facilities Department, FermiGrid Services Group, Assistant Group > > > Leader. > > > > > > _______________________________________________ > > > Xen-users mailing list > > > Xen-users@lists.xensource.com > > > http://lists.xensource.com/xen-users > > > > > > > > > > > > -- > > ------------------------------------------------------------------ > Steven C. Timm, Ph.D (630) 840-8525 > timm@fnal.gov http://home.fnal.gov/~timm/ > Fermilab Computing Division, Scientific Computing Facilities, > Grid Facilities Department, FermiGrid Services Group, Assistant Group > Leader. >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Steven Timm
2008-Apr-28 18:46 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. On Mon, 28 Apr 2008, Todd Deshane wrote:> To get rid of the xenbr1 manually, you should be able to do: > > brctl delif <any interface that is on that bridge> > then, when no more interfaces do: > ifconfig xenbr1 down > brctl delbr xenbr1This worked, xenbr1 is gone.> > Do you get any warning or error to stdout or to the /var/log/xen/* log > files when starting/restarting xend?[2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VBD.set_device not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VBD.set_mode not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VBD.set_type not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VM.get_auto_power_on not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VM.set_auto_power_on not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VM.set_VCPUs_max not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VM.set_VCPUs_at_startup not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: debug.get_all not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: console.get_other_config not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: console.set_other_config not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VIF.get_network not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VIF.set_device not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VIF.set_MAC not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: VIF.set_MTU not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: session.get_all_records not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: event.get_record not found [2008-04-17 15:57:00 3711] WARNING (XendAPI:672) API call: event.get_all not found> > Have you tried to start the network-bridge script on the command line > manually with: > /etc/xen/scripts/network-bridge start >I tried this by hand. /etc/xen/scripts/network-bridge start Nothing to flush. Nothing to flush. Waiting for peth0 to negotiate link.... ...and then it hangs forever. Machine then goes unpingable. Restarting network doesn''t help. rebooting, but not restarting xen, we get the network back.> > It is also not clear to me anymore what works and what doesn''t. Could > you clarify that again? > > Thanks, > Todd >Basic problem: dom0 can''t ping the outside world or be pinged by the outside world. domU can ping dom0 and the outside world. dom0 can ping domU but nothing else. Steve timm> On Mon, Apr 28, 2008 at 11:39 AM, Steven Timm <timm@fnal.gov> wrote: >> Here''s the output of >> >> [root@fnpcsrv5 ~]# brctl show >> bridge name bridge id STP enabled interfaces >> xenbr0 8000.feffffffffff no vif2.0 >> vif1.0 >> peth0 >> vif0.0 >> xenbr1 8000.000000000000 no >> >> and here''s xend-config.sxp >> >> [root@fnpcsrv5 xen]# grep net xend-config.sxp | grep -v ^# >> (network-script network-bridge) >> >> And here''s what the domU config files show at the moment: >> >> vif = [ ''mac=00:16:3e:0f:05:01, bridge=xenbr0'' ] >> >> >> >> ------------ >> I was at one point running a second bridge, but took it out >> during the debugging. Nevertheless the xenbr1 doesn''t go away. >> and I haven''t figured out any brctl commands that will make it go away. >> >> From a similarly-configured working machine on different hardware, this >> is what I wanted to do (and what I had originally configured on this one >> too), and has been working fine for me on many other >> machines. >> >> >> [root@fermigrid5 ~]# brctl show >> bridge name bridge id STP enabled interfaces >> xenbr0 8000.feffffffffff no vif12.0 >> vif10.0 >> vif9.0 >> vif8.0 >> vif7.0 >> peth0 >> vif0.0 >> xenbr1 8000.feffffffffff no vif12.1 >> vif10.1 >> vif9.1 >> vif8.1 >> vif7.1 >> peth1 >> vif0. >> >> >> ------------------------------- >> >> [root@fermigrid5 xen]# grep net xend-config.sxp | grep -v ^# >> (network-script my-network-bridge) >> [root@fermigrid5 xen]# more scripts/my-network-bridge >> #!/bin/sh >> # start bridges on both eth0 and eth1 >> >> XENDIR="/etc/xen/scripts" >> >> $XENDIR/network-bridge "$@" netdev=eth0 bridge=xenbr0 vifnum=0 >> $XENDIR/network-bridge "$@" netdev=eth1 bridge=xenbr1 vifnum=1 >> [root@fermigrid5 xen]# >> >> vif = [ ''mac=00:16:3e:05:05:01, bridge=xenbr0'', ''mac=00:16:3e:05:05:0a, >> bridge=xenbr1'' ] >> >> Hope this helps us figure out what is wrong. >> >> Have seen a couple places on the net that a bios upgrade >> and-or tweak to the broadcom controller is needed >> for the PE1950 to fix related problems. Has anyone tried? >> >> Steve Timm >> >> >> >> >> >> On Mon, 21 Apr 2008, Todd Deshane wrote: >> >> >>> >>> >>> >>> On Thu, Apr 17, 2008 at 9:24 PM, Steven Timm <timm@fnal.gov> wrote: >>> >>> >>>> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on >>>> three new machines today, using a configuration setup that I''ve >>>> used successfully many times before. However, I encountered a >>>> new problem. >>>> >>>> These are Dell Poweredge 1950 servers, by the way. >>>> >>>> >>>>> From lspci >>>>> >>>>> >>>> 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >>>> Gigabit Ethernet (rev 12) >>>> 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >>>> Gigabit Ethernet (rev 12) >>>> >>>> from lspci >>>> Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, >>>> 2006) >>>> ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >>>> eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >>>> found at >>>> mem f4000000, IRQ 16, node addr 0019b9ec40ba >>>> ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >>>> eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >>>> found at >>>> mem f8000000, IRQ 16, node addr 0019b9ec40b8 >>>> >>>> --------------- >>>> >>>> note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 >>>> from what the redhatized non-xen kernel does. This is >>>> undone by ifcfg-eth0. >>>> >>>> When the xen kernel boots, before xend starts, I can see the outside >>>> network just fine. >>>> >>>> [root@fnpcsrv3 xen]# netstat -nNr >>>> Kernel IP routing table >>>> Destination Gateway Genmask Flags MSS Window irtt >>>> Iface >>>> 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 >>>> eth1 >>>> 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 >>>> eth0 >>>> 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 >>>> eth1 >>>> 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 >>>> eth0 >>>> >>>> >>>> [root@fnpcsrv3 xen]# ifconfig >>>> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 >>>> inet addr:131.225.166.97 Bcast:131.225.167.255 Mask: >>>> 255.255.254.0 >>>> inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link >>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>> RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:1000 >>>> RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) >>>> Interrupt:16 Memory:f8000000-f8011100 >>>> >>>> eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA >>>> inet addr:192.168.167.3 Bcast:192.168.167.255 >> Mask:255.255.255.0 >>>> UP BROADCAST MULTICAST MTU:1500 Metric:1 >>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:1000 >>>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) >>>> Interrupt:16 Memory:f4000000-f4011100 >>>> >>>> lo Link encap:Local Loopback >>>> inet addr:127.0.0.1 Mask:255.0.0.0 >>>> inet6 addr: ::1/128 Scope:Host >>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>>> RX packets:192 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) >>>> -------------------------------------------------------------- >>>> >>>> Now here''s ifconfig from an identical system once xend is turned on >>>> >>>> [root@fnpcsrv5 ~]# ifconfig >>>> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 >>>> inet addr:131.225.166.100 Bcast:131.225.167.255 Mask: >>>> 255.255.254.0 >>>> inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link >>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>> RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) >>>> >>>> lo Link encap:Local Loopback >>>> inet addr:127.0.0.1 Mask:255.0.0.0 >>>> inet6 addr: ::1/128 Scope:Host >>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>>> RX packets:21 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) >>>> >>>> peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >>>> RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:1000 >>>> RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) >>>> Interrupt:16 Memory:f4000000-f4011100 >>>> >>>> vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >>>> RX packets:33 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) >>>> >>>> vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >>>> RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:32 >>>> RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) >>>> >>>> vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >>>> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >>>> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >>>> RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:32 >>>> RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) >>>> >>>> xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>> RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) >>>> >>>> xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 >>>> inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link >>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >>>> TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 >>>> collisions:0 txqueuelen:0 >>>> RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) >>>> >>>> ------------------------------------------------------------------------ >>>> >>>> As part of the debugging I dialed back my configuration, which normally >>>> has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one >>>> network interface on each domU and on the dom0. Nevertheless the >>>> problem is the same and I can''t seem to get rid of the xenbr1. >>>> I note that at the start of the xend there is a timeout of about 10-15 >>>> seconds as it is trying to turn on the second bridge. >>>> >>>> Now here is the really strange part. While logged in on the >>>> console of the dom0, I can go ahead and start xen domU''s, and they >>>> go ahead and boot up normally and can see the outside network fine. >>>> >>>> [root@fnpcsrv5 ~]# xm list >>>> Name ID Mem VCPUs State >>>> Time(s) >>>> Domain-0 0 1953 8 r----- >>>> 127.3 >>>> fnpc5x1 1 6000 4 -b---- >>>> 23.1 >>>> fnpc5x4 2 2000 1 -b---- >>>> 20.6 >>>> [root@fnpcsrv5 ~]# >>>> >>>> Oh, and by the way, dom0 is pingable from the domU''s although >>>> it cannot be seen from the outside net. >>>> >>>> What should I be looking at? >>>> >>>> >>> >>> >>> Could you also provide the output of: >>> >>> brctl show >>> >>> grep net /etc/xen/xend-config.sxp | grep -v ''#'' >>> >>> Also, in the domU config files what are you specifying for the bridge? >>> >>> Are you running any custom network scripts (these would be specified in >>> /etc/xen/xend-config.sxp and should have shown up in the output of the >> grep >>> above. >>> >>> Cheers, >>> Todd >>> >>> >>> >>>> >>>> >>>> >>>> Steve Timm >>>> >>>> >>>> >>>> ------------------------------------------------------------------ >>>> Steven C. Timm, Ph.D (630) 840-8525 >>>> timm@fnal.gov http://home.fnal.gov/~timm/ >> <http://home.fnal.gov/%7Etimm/> >>>> >>>> Fermilab Computing Division, Scientific Computing Facilities, >>>> Grid Facilities Department, FermiGrid Services Group, Assistant Group >>>> Leader. >>>> >>>> _______________________________________________ >>>> Xen-users mailing list >>>> Xen-users@lists.xensource.com >>>> http://lists.xensource.com/xen-users >>>> >>>> >>> >>> >> >> -- >> >> ------------------------------------------------------------------ >> Steven C. Timm, Ph.D (630) 840-8525 >> timm@fnal.gov http://home.fnal.gov/~timm/ >> Fermilab Computing Division, Scientific Computing Facilities, >> Grid Facilities Department, FermiGrid Services Group, Assistant Group >> Leader. >> > > _______________________________________________ > Xen-users mailing list > Xen-users@lists.xensource.com > http://lists.xensource.com/xen-users >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Steven Timm
2008-May-05 19:02 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
Here''s another update. Some wiki''s suggested that a firmware upgrade on the NIC and on the PE1950 bios would solve the problem. Unfortunately it did not. Problem is exactly the same as before--that the network will boot OK for starters but as soon as xend is started up (before any domu''s start) the network locks up totally and dom0 is unpingable from the outside. It can ping any domu''s it starts and the domu''s can ping it, and also get to the outside world. I''ve looked through the network wiki but thus far have not found the right diagnostics that I should be checking. Does anyone have Xen 3.1 working on a poweredge 1950? IF so, what did you do? Steve On Thu, 17 Apr 2008, Steven Timm wrote:> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on > three new machines today, using a configuration setup that I''ve > used successfully many times before. However, I encountered a > new problem. > > These are Dell Poweredge 1950 servers, by the way. >> From lspci > 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > Gigabit Ethernet (rev 12) > > from lspci > Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006) > ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found > at > mem f4000000, IRQ 16, node addr 0019b9ec40ba > ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 > eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found > at > mem f8000000, IRQ 16, node addr 0019b9ec40b8 > > --------------- > > note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 > from what the redhatized non-xen kernel does. This is > undone by ifcfg-eth0. > > When the xen kernel boots, before xend starts, I can see the outside network > just fine. > > [root@fnpcsrv3 xen]# netstat -nNr > Kernel IP routing table > Destination Gateway Genmask Flags MSS Window irtt > Iface > 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 > 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 eth0 > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 > 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 eth0 > > > [root@fnpcsrv3 xen]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 > inet addr:131.225.166.97 Bcast:131.225.167.255 Mask:255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) > Interrupt:16 Memory:f8000000-f8011100 > > eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA > inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:16 Memory:f4000000-f4011100 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:192 errors:0 dropped:0 overruns:0 frame:0 > TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) > -------------------------------------------------------------- > > Now here''s ifconfig from an identical system once xend is turned on > > [root@fnpcsrv5 ~]# ifconfig > eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 > inet addr:131.225.166.100 Bcast:131.225.167.255 Mask:255.255.254.0 > inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 > TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:21 errors:0 dropped:0 overruns:0 frame:0 > TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) > > peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 > TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) > Interrupt:16 Memory:f4000000-f4011100 > > vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:33 errors:0 dropped:0 overruns:0 frame:0 > TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) > > vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 > TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) > > vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 > RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 > TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 > collisions:0 txqueuelen:32 > RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) > > xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) > > xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) > > ------------------------------------------------------------------------ > > As part of the debugging I dialed back my configuration, which normally > has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one > network interface on each domU and on the dom0. Nevertheless the > problem is the same and I can''t seem to get rid of the xenbr1. > I note that at the start of the xend there is a timeout of about 10-15 > seconds as it is trying to turn on the second bridge. > > Now here is the really strange part. While logged in on the > console of the dom0, I can go ahead and start xen domU''s, and they > go ahead and boot up normally and can see the outside network fine. > > [root@fnpcsrv5 ~]# xm list > Name ID Mem VCPUs State Time(s) > Domain-0 0 1953 8 r----- 127.3 > fnpc5x1 1 6000 4 -b---- 23.1 > fnpc5x4 2 2000 1 -b---- 20.6 > [root@fnpcsrv5 ~]# > > Oh, and by the way, dom0 is pingable from the domU''s although > it cannot be seen from the outside net. > > What should I be looking at? > > Steve Timm > > > > ------------------------------------------------------------------ > Steven C. Timm, Ph.D (630) 840-8525 > timm@fnal.gov http://home.fnal.gov/~timm/ > Fermilab Computing Division, Scientific Computing Facilities, > Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. > > _______________________________________________ > Xen-users mailing list > Xen-users@lists.xensource.com > http://lists.xensource.com/xen-users >-- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Steven Timm
2008-May-06 14:00 UTC
Re: [Xen-users] help--dom0 network goes unpingable when xend starts
By following the section of the following wiki: http://mywiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround in particular downloading the broadcom netextreme MS-DOS utilities mentioned there, booting under DOS, and disabling the IPMI network management on both broadcom nic''s on the poweredge 1950, I can now see the network from dom0 and domU after the Xen instance is started up. This works both with single bridge and dual bridge configurations. Steve Timm On Mon, 5 May 2008, Steven Timm wrote:> Here''s another update. Some wiki''s suggested that a > firmware upgrade on the NIC and on the PE1950 bios would solve > the problem. Unfortunately it did not. Problem is exactly > the same as before--that the network will boot OK for starters but > as soon as xend is started up (before any domu''s start) the > network locks up totally and dom0 is unpingable from the outside. > It can ping any domu''s it starts and the domu''s can ping it, and > also get to the outside world. > > I''ve looked through the network wiki but thus far have not found > the right diagnostics that I should be checking. > > Does anyone have Xen 3.1 working on a poweredge 1950? IF so, what did > you do? > > Steve > > > On Thu, 17 Apr 2008, Steven Timm wrote: > >> I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on >> three new machines today, using a configuration setup that I''ve >> used successfully many times before. However, I encountered a >> new problem. >> >> These are Dell Poweredge 1950 servers, by the way. >>> From lspci >> 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >> Gigabit Ethernet (rev 12) >> 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 >> Gigabit Ethernet (rev 12) >> >> from lspci >> Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, >> 2006) >> ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >> eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >> found at >> mem f4000000, IRQ 16, node addr 0019b9ec40ba >> ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16 >> eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz >> found at >> mem f8000000, IRQ 16, node addr 0019b9ec40b8 >> >> --------------- >> >> note that the Xen kernel 2.6.18 picks the opposite mac addresses as eth0 >> from what the redhatized non-xen kernel does. This is >> undone by ifcfg-eth0. >> >> When the xen kernel boots, before xend starts, I can see the outside >> network just fine. >> >> [root@fnpcsrv3 xen]# netstat -nNr >> Kernel IP routing table >> Destination Gateway Genmask Flags MSS Window irtt >> Iface >> 192.168.167.0 0.0.0.0 255.255.255.0 U 0 0 0 >> eth1 >> 131.225.166.0 0.0.0.0 255.255.254.0 U 0 0 0 >> eth0 >> 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 >> eth1 >> 0.0.0.0 131.225.167.200 0.0.0.0 UG 0 0 0 >> eth0 >> >> >> [root@fnpcsrv3 xen]# ifconfig >> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:40:B8 >> inet addr:131.225.166.97 Bcast:131.225.167.255 Mask:255.255.254.0 >> inet6 addr: fe80::219:b9ff:feec:40b8/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:591697 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:3060 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:38067586 (36.3 MiB) TX bytes:395536 (386.2 KiB) >> Interrupt:16 Memory:f8000000-f8011100 >> >> eth1 Link encap:Ethernet HWaddr 00:19:B9:EC:40:BA >> inet addr:192.168.167.3 Bcast:192.168.167.255 Mask:255.255.255.0 >> UP BROADCAST MULTICAST MTU:1500 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) >> Interrupt:16 Memory:f4000000-f4011100 >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:16436 Metric:1 >> RX packets:192 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:15314 (14.9 KiB) TX bytes:15314 (14.9 KiB) >> -------------------------------------------------------------- >> >> Now here''s ifconfig from an identical system once xend is turned on >> >> [root@fnpcsrv5 ~]# ifconfig >> eth0 Link encap:Ethernet HWaddr 00:19:B9:EC:4A:21 >> inet addr:131.225.166.100 Bcast:131.225.167.255 >> Mask:255.255.254.0 >> inet6 addr: fe80::219:b9ff:feec:4a21/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:508292 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:33 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:30786266 (29.3 MiB) TX bytes:1658 (1.6 KiB) >> >> lo Link encap:Local Loopback >> inet addr:127.0.0.1 Mask:255.0.0.0 >> inet6 addr: ::1/128 Scope:Host >> UP LOOPBACK RUNNING MTU:16436 Metric:1 >> RX packets:21 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:21 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:1916 (1.8 KiB) TX bytes:1916 (1.8 KiB) >> >> peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:523679 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:15964 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:1000 >> RX bytes:33836052 (32.2 MiB) TX bytes:1132609 (1.0 MiB) >> Interrupt:16 Memory:f4000000-f4011100 >> >> vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:33 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:508293 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:1658 (1.6 KiB) TX bytes:30786336 (29.3 MiB) >> >> vif1.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:7848 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:499340 errors:0 dropped:159 overruns:0 carrier:0 >> collisions:0 txqueuelen:32 >> RX bytes:347417 (339.2 KiB) TX bytes:30239848 (28.8 MiB) >> >> vif2.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link >> UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 >> RX packets:7867 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:496186 errors:0 dropped:191 overruns:0 carrier:0 >> collisions:0 txqueuelen:32 >> RX bytes:346478 (338.3 KiB) TX bytes:30050363 (28.6 MiB) >> >> xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:508099 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:23650570 (22.5 MiB) TX bytes:90 (90.0 b) >> >> xenbr1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 >> inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link >> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >> TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 >> collisions:0 txqueuelen:0 >> RX bytes:0 (0.0 b) TX bytes:468 (468.0 b) >> >> ------------------------------------------------------------------------ >> >> As part of the debugging I dialed back my configuration, which normally >> has a xenbr0 and a xenbr1, to use a just a xenbr0 and have just one >> network interface on each domU and on the dom0. Nevertheless the >> problem is the same and I can''t seem to get rid of the xenbr1. >> I note that at the start of the xend there is a timeout of about 10-15 >> seconds as it is trying to turn on the second bridge. >> >> Now here is the really strange part. While logged in on the >> console of the dom0, I can go ahead and start xen domU''s, and they >> go ahead and boot up normally and can see the outside network fine. >> >> [root@fnpcsrv5 ~]# xm list >> Name ID Mem VCPUs State Time(s) >> Domain-0 0 1953 8 r----- >> 127.3 >> fnpc5x1 1 6000 4 -b---- >> 23.1 >> fnpc5x4 2 2000 1 -b---- >> 20.6 >> [root@fnpcsrv5 ~]# >> >> Oh, and by the way, dom0 is pingable from the domU''s although >> it cannot be seen from the outside net. >> >> What should I be looking at? >> >> Steve Timm >> >> >> >> ------------------------------------------------------------------ >> Steven C. Timm, Ph.D (630) 840-8525 >> timm@fnal.gov http://home.fnal.gov/~timm/ >> Fermilab Computing Division, Scientific Computing Facilities, >> Grid Facilities Department, FermiGrid Services Group, Assistant Group >> Leader. >> >> _______________________________________________ >> Xen-users mailing list >> Xen-users@lists.xensource.com >> http://lists.xensource.com/xen-users >> > >-- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users