similar to: PowerWalker VFI 2000 RT LCD

UPS: PowerWalker VFI 3000RT LCD CentOS 6.5, nut installed from RPM package: nut-2.6.5-2.el6.x86_64 nut-client-2.6.5-2.el6.x86_64 Driver: blazer_usb Problem description: USB device "loops" when starting blazer_usb. USB device permissions are ok. Receives some information. Error messages: "failed to claim USB device: could not claim interface 0: Device or resource busy"

Hello! I'm trying to use nut with a Ippon Smart Winner 3000 UPS (http://shop.key.ru/photo/items/45535.jpg) which looks like a custom-labeled OEM model of the megatec branch. I tried both the megatec_usb and the blazer_usb drivers for it, with a obvious config section: [ippon] driver = blazer_usb port = auto vendorid = 06da productid = 0003 desc = "Ippon Smart Winner 3000" If I

hi! When I turn on my pc everything works fine, but if I restart fails (I'm not sure if this is true at 100%)?(then, i can do 'sudo /etc/init.d/nut restart' and it works) But what is certain is that sometimes when start up the pc it works and sometimes fails, can be a problem with the start time (i have a fast ssd) and the initialization of the driver and the usb port? thanks! syslog:

[As posted as Ubuntu Question #184284 on Launchpad] Hi, I try to set up nut (2.4.3) on my Lucid (10.04.3 LTS) to make use of my old but very trusty UPS (Best Power Fortress 660 LI). Yes, this UPS is old (about 16 years), but with its third battery pack last week it is as good as new. It runs perfectly well with Windows XP, Vista and even Windows 7. But not so with Ubuntu and nut. After

Hi I Bought a cheap Plexus 800VA UPS from ebuyer : http://www.ebuyer.com/product/240319 to use with my Netgear ReadyNAS duo. Initial version of NUT was very old and NAS didn't detect it although in the NAS log it said "UPS Disconnected". Syslog did send the following : Jan 25 12:46:36 nas-27lfc kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 Jan 25 12:46:37

Hello again! Sorry for not being able to test this before. Ulisses, please apply the patch to fix typo in my e-mail address. I've compiled it against nut-2.6.5 about 10 hours ago. It was everything fine until now. I'm seeing CHRG but the ups led wasn't blinking at all. Vendor software was strangely showing charging also. I am assuming this is expected behavior. I've set the

cmd test.battery.start.deep was not tested yet. cmd test.battery.start.quick works as expected. cmd test.battery.start 120 works as expected. cmd test.battery.stop works as expected. cmd beeper.toggle works as expected. cmd shutdown.return works as expected. cmd shutdown.reboot does not work entirely. After a minute, UPS is shut down but didn't come back. (Issuing shutdown.stop power up it

Hello, I have just installed nut_2.6.0 from Debian testing, do anyone know the correct driver for this ups? The blazer_usb don't report battery-charge, the bundled software report charge and runtime. root at pluto<~>upsc powerwalker battery.voltage: 40.86 battery.voltage.nominal: 36.0 beeper.status: enabled device.mfr: device.model: HV 1K device.type: ups driver.name: blazer_usb

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hi, I know it's been a topic many times here, but I've searched the archives, googled for days, and I simply don't believe, that there is still no solution to this. I'm using a PowerCom BNT-600AP ups with usb port. I've downloaded the latest version from svn, compiled it, and tried to use it: * megatec(_usb) - no luck, it did not find the UPS (I?ve read in this list, that

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

Hello, i've a problem, this is my configuration: - Atlantis Land UPS with serial port - a generic RS232 to USB cable adapter (QinHeng Electronics HL-340 USB-Serial adapter for linux). The problem is in the syslog file where i find: [...] Aug 19 09:07:25 ProLiant megatec[1126]: Communications with UPS lost: No status from UPS. Aug 19 09:07:26 ProLiant megatec[1126]: Communications with UPS

On 10/08/2012 21:58, nut-upsuser-request at lists.alioth.debian.org wrote: >>> Arnaud Quette<aquette.dev<at> gmail.com> writes: >>>> 2012/6/3 Chris Rees<crees<at> freebsd.org>: >>>>> Hi all, >>>> Hi Chris, >>>> >>>>> After some research I've found that this device should run with the

Hi list, on my previous (lenny or squeeze) machine, I had it up and running, but that machine and configs are gone - and on my new jessie machine (see device and config details below) I cannot start the driver: # /lib/nut/bestups -DDDDD -a Patriot_Pro_II_750 0.000000 debug level is '5' 0.000806 send_to_all: SETINFO device.type "ups" 0.000842 send_to_all:

Hello There, I tried your advice and i don't think it works either, See the logs, " /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x vendorid=... -x productid=... -x subdriver=... Network UPS Tools - Generic HID driver 0.52 (2.8.0-2557-g81fca30b2) USB communication driver (libusb 1.0) 0.46 ?? 0.000000??? [D3] main_arg: var='port' val='auto' ??

<facepalm ;)> the ellispis "something=..." were supposed to be replaced by your device ID numbers, etc. On Sat, Sep 23, 2023, 18:26 FatGear <fatgear1 at free.fr> wrote: > Hello There, > > I tried your advice and i don't think it works either, > > See the logs, > > " > > /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

No progress has been made: cable is UPS - PC 6 - 3 7 - 5 9 - 2 for ./blazer_ser -DDDDD -a infosec 0.000000 send_to_all: SETINFO driver.parameter.port "/dev/ttyS1" 0.000323 debug level is '5' 0.103068 send_to_all: SETINFO device.type "ups" 0.103104 send_to_all: SETINFO driver.version "2.7.3" 0.103118 send_to_all: SETINFO

Hi, I'm running the latest version of NUT and with the above UPS and I keep getting the following error: "tripplite_usb[3308]: Error reading B value: Device detached? (error 0: could not claim interface 0: Device or resource busy)" The device keeps disconnecting and re-connecting until fails. I've tried to see if others are getting this - but I could not locate a